GOST 2.311-68
Group T52
INTERSTATE STANDARD
Unified system of design documentation
IMAGE OF THREAD
Unified system for design documentation. Image of screw
ISS 01.100.20
Date of introduction 1971-01-01
INFORMATION DATA
1. DEVELOPED AND INTRODUCED by the Committee of Standards, Measures and Measuring Instruments under the Council of Ministers of the USSR
2. APPROVED AND ENTERED INTO EFFECT by Resolution of the Committee of Standards, Measures and Measuring Instruments under the Council of Ministers of the USSR dated May 28, 1968 N 755
3. The standard corresponds to ST SEV 284-76
4. INSTEAD GOST 3459-59
5. EDITION (August 2007) with Amendment No. 1, approved in April 1987 (IUS 7-87)
1. This standard establishes the rules for depicting and applying thread designations on drawings of all industries and construction.
The standard corresponds to ST SEV 284-76.
2. The carving is depicted:
a) on the rod - with solid main lines along the outer diameter of the thread and solid thin lines - along the inner diameter.
In images obtained by projection onto a plane parallel to the axis of the rod, a continuous thin line along the internal diameter of the thread is drawn along the entire length of the thread without a runoff, and in views obtained by projection onto a plane perpendicular to the axis of the rod, an arc is drawn along the internal diameter of the thread, approximately equal to a circle open anywhere (Fig. 1, 2);
Damn.1
Damn.2
b) in the hole - with solid main lines along the internal diameter of the thread and solid thin lines - along the outer diameter.
On sections parallel to the axis of the hole, a continuous thin line along the outer diameter of the thread is drawn along the entire length of the thread without running, and on images obtained by projection onto a plane perpendicular to the axis of the hole, an arc is drawn along the outer diameter of the thread, approximately equal to a circle, open at any place (Fig. 3, 4).
Damn.3
Damn.4
When depicting a thread, a solid thin line is applied at a distance of at least 0.8 mm from the main line and no more than the thread pitch.
3. The thread, shown as invisible, is depicted with dashed lines of the same thickness along the outer and inner diameters (Fig. 5).
Damn.5
4. The line defining the thread boundary is drawn on the rod and in the threaded hole at the end of the full thread profile (before the start of the run). The thread boundary is drawn to the line of the outer diameter of the thread and is depicted as a solid main or dashed line if the thread is depicted as invisible (Fig. 6-8).
Damn.7
Damn.8
5. Hatching in sections and sections is carried out to the line of the outer diameter of the thread on the rods and to the line of the inner diameter in the hole, i.e. in both cases to a solid main line (see drawings 3, 4, 7, 8).
6. The size of the thread length with a full profile (without run-out) on the rod and in the hole is indicated as shown in Figure 9 A and 10 A.
The size of the thread length (with run-out) is indicated as shown in Fig. 9 b and 10 b.
If it is necessary to indicate the amount of run-off on the rod, the dimensions are applied as shown in Fig. 9 V.
The thread run-out is depicted as a solid thin straight line, as shown in Fig. 9 b, V and 10 b.
Damn.9
Damn.10
An undercut of a thread made all the way is shown as shown in Fig. 11 A And V.
It is allowed to depict an undercut of the thread, as shown in Fig. 11 b And G.
7. The main plane of the conical thread on the rod, if necessary, is indicated by a thin solid line, as shown in Figure 12.
Damn.12
8. In drawings in which threads are not made, the end of a blind threaded hole may be depicted as shown in Figures 13 and 14, even if there is a difference between the depth of the thread hole and the length of the thread.
Damn.13
Damn.14
9. Chamfers on a threaded rod and in a threaded hole that do not have a special structural purpose are not shown in projection onto a plane perpendicular to the axis of the rod or hole (Fig. 15-17). A solid thin line depicting the thread on the rod should intersect the chamfer boundary line (see Fig. 15).
Damn.15
Damn.16
Damn.17
10. A thread with a non-standard profile is shown in one of the ways shown in Figure 18, with all the necessary dimensions and maximum deviations. In addition to the dimensions and maximum deviations of the thread, the drawing indicates additional data on the number of starts, the left direction of the thread, etc. with the addition of the word "Carving".
11. On the sections of a threaded connection in the image on a plane parallel to its axis, only the part of the thread that is not covered by the thread of the rod is shown in the hole (Fig. 19, 20).
Damn.19
Damn.20
12. Thread designations indicate, according to the relevant standards, the dimensions and maximum deviations of the threads and relate them for all threads, except conical and cylindrical pipe threads, to the outer diameter, as shown in Fig. 21, 22.
Damn.21
Damn.22
Designations for conical threads and cylindrical pipe threads are applied as shown in Fig. 23.
Damn.23
Note. The "*" sign marks the location where the thread designation is applied.
13. Special threads with a standard profile are abbreviated as Sp and a thread symbol.
(Changed edition, Amendment No. 1).
Electronic document text
prepared by Kodeks JSC and verified against:
official publication
Unified system of design documentation:
Sat. GOST. - M.: Standartinform, 2007
GOST 2.311-68
Group T52
INTERSTATE STANDARD
Unified system of design documentation
IMAGE OF THREAD
Unified system for design documentation. Image of screw
ISS 01.100.20
Date of introduction 1971-01-01
INFORMATION DATA
1. DEVELOPED AND INTRODUCED by the Committee of Standards, Measures and Measuring Instruments under the Council of Ministers of the USSR
2. APPROVED AND ENTERED INTO EFFECT by Resolution of the Committee of Standards, Measures and Measuring Instruments under the Council of Ministers of the USSR dated May 28, 1968 N 755
3. The standard corresponds to ST SEV 284-76
4. INSTEAD GOST 3459-59
5. EDITION (August 2007) with Amendment No. 1, approved in April 1987 (IUS 7-87)
1. This standard establishes the rules for depicting and applying thread designations on drawings of all industries and construction.
The standard corresponds to ST SEV 284-76.
2. The carving is depicted:
a) on the rod - with solid main lines along the outer diameter of the thread and solid thin lines - along the inner diameter.
In images obtained by projection onto a plane parallel to the axis of the rod, a continuous thin line along the internal diameter of the thread is drawn along the entire length of the thread without a runoff, and in views obtained by projection onto a plane perpendicular to the axis of the rod, an arc is drawn along the internal diameter of the thread, approximately equal to a circle open anywhere (Fig. 1, 2);
Damn.1
Damn.2
b) in the hole - with solid main lines along the internal diameter of the thread and solid thin lines - along the outer diameter.
On sections parallel to the axis of the hole, a continuous thin line along the outer diameter of the thread is drawn along the entire length of the thread without running, and on images obtained by projection onto a plane perpendicular to the axis of the hole, an arc is drawn along the outer diameter of the thread, approximately equal to a circle, open at any place (Fig. 3, 4).
Damn.3
Damn.4
When depicting a thread, a solid thin line is applied at a distance of at least 0.8 mm from the main line and no more than the thread pitch.
3. The thread, shown as invisible, is depicted with dashed lines of the same thickness along the outer and inner diameters (Fig. 5).
Damn.5
4. The line defining the thread boundary is drawn on the rod and in the threaded hole at the end of the full thread profile (before the start of the run). The thread boundary is drawn to the line of the outer diameter of the thread and is depicted as a solid main or dashed line if the thread is depicted as invisible (Fig. 6-8).
Damn.7
Damn.8
5. Hatching in sections and sections is carried out to the line of the outer diameter of the thread on the rods and to the line of the inner diameter in the hole, i.e. in both cases to a solid main line (see drawings 3, 4, 7, 8).
6. The size of the thread length with a full profile (without run-out) on the rod and in the hole is indicated as shown in Figure 9 A and 10 A.
The size of the thread length (with run-out) is indicated as shown in Fig. 9 b and 10 b.
If it is necessary to indicate the amount of run-off on the rod, the dimensions are applied as shown in Fig. 9 V.
The thread run-out is depicted as a solid thin straight line, as shown in Fig. 9 b, V and 10 b.
Damn.9
Damn.10
An undercut of a thread made all the way is shown as shown in Fig. 11 A And V.
It is allowed to depict an undercut of the thread, as shown in Fig. 11 b And G.
7. The main plane of the conical thread on the rod, if necessary, is indicated by a thin solid line, as shown in Figure 12.
Damn.12
8. In drawings in which threads are not made, the end of a blind threaded hole may be depicted as shown in Figures 13 and 14, even if there is a difference between the depth of the thread hole and the length of the thread.
Damn.13
Damn.14
9. Chamfers on a threaded rod and in a threaded hole that do not have a special structural purpose are not shown in projection onto a plane perpendicular to the axis of the rod or hole (Fig. 15-17). A solid thin line depicting the thread on the rod should intersect the chamfer boundary line (see Fig. 15).
Damn.15
Damn.16
Damn.17
10. A thread with a non-standard profile is shown in one of the ways shown in Figure 18, with all the necessary dimensions and maximum deviations. In addition to the dimensions and maximum deviations of the thread, the drawing indicates additional data on the number of starts, the left direction of the thread, etc. with the addition of the word "Carving".
11. On the sections of a threaded connection in the image on a plane parallel to its axis, only the part of the thread that is not covered by the thread of the rod is shown in the hole (Fig. 19, 20).
Damn.19
Damn.20
12. Thread designations indicate, according to the relevant standards, the dimensions and maximum deviations of the threads and relate them for all threads, except conical and cylindrical pipe threads, to the outer diameter, as shown in Fig. 21, 22.
Damn.21
Damn.22
Designations for conical threads and cylindrical pipe threads are applied as shown in Fig. 23.
Damn.23
Note. The "*" sign marks the location where the thread designation is applied.
13. Special threads with a standard profile are abbreviated as Sp and a thread symbol.
(Changed edition, Amendment No. 1).
Electronic document text
prepared by Kodeks JSC and verified against:
official publication
Unified system of design documentation:
Sat. GOST. - M.: Standartinform, 2007
This standard establishes the rules for depicting and applying thread symbols on drawings for all industries and construction.
| Designation: | GOST 2.311-68* |
| Russian name: | ESKD. Thread image |
| Status: | current Edition (April 2000) |
| Replaces: | GOST 3459-59 “Drawings in mechanical engineering. Image and designation of thread" |
| Date of text update: | 01.10.2008 |
| Date added to the database: | 01.02.2009 |
| Effective date: | 01.01.1971 |
| Designed by: | State Standard of the USSR |
| Approved: | State Standard of the USSR (01.12.1967) |
| Published: | IPC Standards Publishing House No. 2000 |
GOST 2.311-68
INTERSTATE STANDARD
UNIFIED SYSTEM OF DESIGN DOCUMENTATION
THREAD IMAGE
IPC PUBLISHING HOUSE OF STANDARDS
Moscow
INTERSTATE STANDARD
| Unified system of design documentation IMAGETHREADS Unified system for design documentation. | GOST |
Date of introduction 01.01.71
1. This standard establishes the rules for depicting and applying thread designations on drawings of all industries and construction.
The standard corresponds to STSEV 284-76.
2. The carving is depicted:
a) on the rod - with solid main lines along the outer diameter of the thread and solid thin lines - with the inner diameter.
In images obtained by projection onto a plane parallel to the axis of the rod, a continuous thin line along the internal diameter of the thread is drawn along the entire length of the thread without a runoff, and in views obtained by projection onto a plane perpendicular to the axis of the rod, an arc approximately equal to 3/4 of the circle is drawn along the internal diameter of the thread , open anywhere (Fig. , );
Crap. 1
Crap. 2
b) in the hole - with solid main lines along the internal diameter of the thread and solid thin lines along the outer diameter.
On sections parallel to the axis of the hole, a continuous thin line along the outer diameter of the thread is drawn along the entire length of the thread without a runoff, and on images obtained by projecting onto a plane perpendicular to the axis of the hole, an arc approximately equal to 3/4 of the circle, open at any place, is drawn along the outer diameter of the thread (crap. ,).
Crap. 3
Crap. 4
A solid thin line when depicting a thread is applied at a distance of at least 0.8 mm from the main line and no more than the thread pitch.
3. The thread, shown as invisible, is depicted with dashed lines of the same thickness along the outer and inner diameters (drawing).
Crap. 5
4. The line defining the thread boundary is drawn on the rod and in the threaded hole at the end of the full thread profile (before the start of the run). The thread boundary is drawn to the line of the outer diameter of the thread and is depicted as a solid main or dashed line if the thread is depicted as invisible (Fig. -).
Crap. 6
Crap. 7
Crap. 8
5. Hatching in sections and sections is carried out to the line of the outer diameter of the thread on the rods and to the line of the internal diameter in the hole, i.e. in both cases to the solid main line (see drawing ,, , ).
6. The size of the length of the thread with a full profile (without run-off) on the rod and in the hole is indicated as shown in the drawing. A and damn. A.
The size of the thread length (alongside) is indicated as shown in Fig. b and damn. b.
If it is necessary to indicate the amount of run-off on the rod, the dimensions are applied, as shown in Fig. V.
The thread run-out is depicted as a solid thin straight line, as shown in the diagram. b, V and damn. b.
Crap. 9
Crap. 10
An undercut of a thread made all the way is depicted as shown in Fig. A And V.
It is allowed to depict an undercut of the thread, as shown in Fig. b And G.
Crap. eleven
(Changed edition, Amendment No. 1).
7. The main plane of the conical thread on the rod, if necessary, is indicated by a thin solid line, as shown in Fig. .
Crap. 12
8. In the drawings, according to which the thread is not performed, the end of a blind threaded hole is allowed to be depicted as shown in Fig. and , even if there is a difference between the depth of the thread hole and the length of the thread.
Crap. 13
Crap. 14
9. Chamfers on a threaded rod and in a threaded hole that do not have a special structural purpose are not shown in projection onto a plane perpendicular to the axis of the rod or hole (Fig. -). A solid thin line depicting the thread on the rod should intersect the chamfer boundary line (see drawing).
Crap. 15
Crap. 16
Crap. 17
10. A thread with a non-standard profile is shown in one of the ways shown in Fig. , absolutely necessary dimensions and maximum deviations. In addition to the dimensions and maximum deviations of the thread, the drawing indicates additional data on the number of starts, the left direction of the thread, etc. with the addition of the word "Carving".
GOST 2.311-68* “ESKD. Image of carving"
GOST 2.311-68
INTERSTATE STANDARD
UNIFIED SYSTEM OF DESIGN DOCUMENTATION
THREAD IMAGE
IPC PUBLISHING HOUSE OF STANDARDS
Moscow
INTERSTATE STANDARD
|
Unified system of design documentation IMAGETHREADS Unified system for design documentation. |
GOST |
Date of introduction 01.01.71
1. This standard establishes the rules for depicting and applying thread designations on drawings of all industries and construction.
The standard corresponds to ST SEV 284-76.
2. The carving is depicted:
a) on the rod - with solid main lines along the outer diameter of the thread and solid thin lines - along the inner diameter.
In images obtained by projection onto a plane parallel to the axis of the rod, a continuous thin line along the internal diameter of the thread is drawn along the entire length of the thread without a runoff, and in views obtained by projection onto a plane perpendicular to the axis of the rod, an arc is drawn along the internal diameter of the thread, approximately equal to 3/4 of a circle, open anywhere (Fig. , );
Crap. 1
Crap. 2
b) in the hole - with solid main lines along the inner diameter of the thread and solid thin lines - along the outer diameter.
On cuts parallel to the axis of the hole, a solid thin line along the outer diameter of the thread is drawn for the entire length of the thread without run-off, and on images obtained by projecting onto a plane perpendicular to the axis of the hole, an arc approximately equal to 3/4 of the circle is drawn along the outer diameter of the thread, open anywhere (damn. , ).
Crap. 3
Crap. 4
A solid thin line when depicting a thread is applied at a distance of at least 0.8 mm from the main line and not more than the thread pitch.
3. The thread, shown as invisible, is depicted by dashed lines of the same thickness along the outer and inner diameters (Fig.).
Crap. 5
4. The line defining the thread boundary is applied on the rod and in the threaded hole at the end of the full thread profile (before the start of the run). The thread boundary is drawn to the line of the outer diameter of the thread and is depicted as a solid main or dashed line if the thread is shown as invisible (Fig. -).
Crap. 6
Crap. 7
Crap. 8
5. Hatching in sections and sections is carried out to the line of the outer diameter of the thread on the rods and to the line of the internal diameter in the hole, i.e. in both cases to the solid main line (see drawing , , , ).
6. The length of the thread with a full profile (without run-out) on the rod and in the hole is indicated as shown in Fig. A and damn. A.
The thread length (with run-out) is indicated as shown in Fig. b and damn. b.
If it is necessary to indicate the amount of run-off on the rod, the dimensions are applied as shown in Fig. V.
The run of the thread is depicted as a solid thin straight line, as shown in Fig. b, V and damn. b.
Crap. 9
Crap. 10
An undercut of a thread made all the way is depicted as shown in Fig. A And V.
It is allowed to depict an undercut of the thread, as shown in Fig. b And G.
Crap. eleven
(Changed edition, Amendment No. 1).
7. The main plane of the conical thread on the rod, if necessary, is indicated by a thin solid line, as shown in Fig. .
Crap. 12
8. In drawings in which threads are not made, the end of a blind threaded hole may be depicted as shown in Fig. and, even if there is a difference between the depth of the thread hole and the length of the thread.
Crap. 13
Crap. 14
9. Chamfers on a threaded rod and in a threaded hole that do not have a special structural purpose are not shown in projection onto a plane perpendicular to the axis of the rod or hole (Fig. -). A solid thin line depicting the thread on the rod should intersect the chamfer boundary line (see drawing).
Crap. 15
Crap. 16
Crap. 17
10. A thread with a non-standard profile is shown in one of the ways shown in Fig. , with all necessary dimensions and maximum deviations. In addition to the dimensions and maximum deviations of the thread, the drawing indicates additional data on the number of starts, the left direction of the thread, etc. with the addition of the word "Carving".
Crap. 18
11. On the sections of a threaded connection in the image on a plane parallel to its axis, only the part of the thread that is not covered by the thread of the rod is shown in the hole (Fig.
GOST 2.311-68
Group T52
INTERSTATE STANDARD
Unified system of design documentation IMAGE OF THREAD
Unified system for design documentation. Image of screw
ISS 01.100.20
Date of introduction 1971-01-01
INFORMATION DATA
1. DEVELOPED AND INTRODUCED by the Committee of Standards, Measures and Measuring Instruments under the Council of Ministers of the USSR
2. APPROVED AND ENTERED INTO EFFECT by Resolution of the Committee of Standards, Measures and Measuring Instruments under the Council of Ministers of the USSR dated May 28, 1968 N 755
3. The standard complies with ST SEV 284-76
4. INSTEAD GOST 3459-59
5. EDITION (August 2007) with Amendment No. 1, approved in April 1987 (ICS 7-87)
1. This standard establishes the rules for the image and application of the thread designation in the drawings of all industries and construction.
The standard corresponds to ST SEV 284-76.
2. The carving is depicted:
a) on the rod - with solid main lines along the outer diameter of the thread and solid thin lines - along the inner diameter.
On images obtained by projecting onto a plane parallel to the axis of the rod, a solid thin line along the inner diameter of the thread is drawn for the entire length of the thread without run-off, and on views obtained by projecting onto a plane perpendicular to the axis of the rod, along
an arc approximately equal to a circle is drawn to the inner diameter of the thread, open anywhere (Fig. 1, 2);
b) in the hole - with solid main lines along the internal diameter of the thread and solid thin lines - along the outer diameter.
On sections parallel to the axis of the hole, a continuous thin line along the outer diameter of the thread is drawn along the entire length of the thread without running, and on images obtained by projection onto a plane perpendicular to the axis of the hole, an arc is drawn along the outer diameter of the thread,
approximately equal to a circle, open anywhere (Fig. 3, 4).
When depicting a thread, a solid thin line is applied at a distance of at least 0.8 mm from the main line and no more than the thread pitch.
3. The thread, shown as invisible, is depicted with dashed lines of the same thickness along the outer and inner diameters (Fig. 5).
4. The line defining the thread boundary is drawn on the rod and in the threaded hole at the end of the full thread profile (before the start of the run). The thread boundary is drawn to the line of the outer diameter of the thread and is depicted as a solid main or dashed line if the thread is depicted as invisible (Fig. 6-8).
5. Hatching in sections and sections is carried out to the line of the outer diameter of the thread on the rods
And to the line of the internal diameter in the hole, i.e. in both cases up to the solid main line
(see drawings 3, 4, 7, 8).
6. The size of the thread length with a full profile (without run-out) on the rod and in the hole is indicated as shown in Figures 9a and 10a.
The size of the thread length (with run-off) is indicated as shown in Figures 9b and 10b.
If it is necessary to indicate the amount of run-off on the rod, the dimensions are applied as shown in Fig. 9c.
The thread run-out is depicted as a solid thin straight line, as shown in Fig. 9b, c and 10b.
An undercut of a thread made all the way is shown as shown in Fig. 11a and c.
It is allowed to depict an undercut of the thread, as shown in Fig. 11b and d.
7. The main plane of the conical thread on the rod, if necessary, is indicated by a thin solid line, as shown in Figure 12.
8. In drawings in which threads are not made, the end of a blind threaded hole may be depicted as shown in Figures 13 and 14, even if there is a difference between the depth of the thread hole and the length of the thread.
9. Chamfers on a threaded rod and in a threaded hole that do not have a special structural purpose are not shown in projection onto a plane perpendicular to the axis of the rod or hole (Fig. 15-17). A solid thin line depicting the thread on the rod should intersect the chamfer boundary line (see Fig. 15).
10. A thread with a non-standard profile is shown in one of the ways shown in Figure 18, with all the necessary dimensions and maximum deviations. In addition to the dimensions and maximum deviations of the thread, the drawing indicates additional data on the number of starts, the left direction of the thread, etc. with the addition of the word "Carving".
11. On the sections of a threaded connection in the image on a plane parallel to its axis, only the part of the thread that is not covered by the thread of the rod is shown in the hole (Fig. 19, 20).
12. Thread designations indicate, according to the relevant standards, the dimensions and maximum deviations of the threads and relate them for all threads, except conical and cylindrical pipe threads, to the outer diameter, as shown in Fig. 21, 22.
Designations for conical threads and cylindrical pipe threads are applied as shown in Fig. 23.
Note. The "*" sign marks the location where the thread designation is applied.
13. Special threads with a standard profile are abbreviated as Sp and a thread symbol.
(Changed edition, Amendment No. 1).
The electronic text of the document was prepared by CJSC "Kodeks" and verified by: official publication
Unified system of design documentation: Sat. GOST. - M.: Standartinform, 2007