Everyone, who has a telephone, modem and the Internet, has come across at least once with such a problem as a broken connector, namely, broken "tongue". The one that presses the connector in the port so that it provides a reliable connection. In fact, it is not so difficult to solve this trouble-problem. Moreover, after the repair, such a connector will become even better than was in the original.
What we need
The broken connector will be repaired using two conventional plastic screeds that are used when working with all the same cables. Immediately it should be noted that although the resulting design and will be sufficiently strong, it should be considered exclusively as a temporary measure. It is best to cut the cable as soon as possible by using a special tool and a new connector.
For repair, it will also be necessary knife, plumbings, passatias or (if suddenly there is in the house) a pistol for tightening cable ties. At the same time, the screeds must be the right size - the head is up to 4.3 mm. Such a screed will be good to enter the socket and securely fix the connector. To remove the head, it will have to make a small effort to it.
The working process
There is nothing complicated in the process of repair. To begin with, we take one tie and cut her head with an indent of 4.5 mm. After that, use the knife and cut the head so that it turns out a flat ending. Now, to ensure the efficiency of the whole design, the resulting part of the head (our workpiece) with the tail should be bend.
After that, it remains quite a bit - fix the "tongue". To do this, we take the second screed and tighten it around the network cable using a gun or a pistol. At the final stage of the repair work, we set up the length of the "tongue" of the design. Ideally, he must get to the broken head of the connector.
Good day Dear blog readers Website. If your Internet cable (twisted pair) overwhelmed a dog or a cat, it is transmitted to furniture or was damaged by another mechanical manner, it can be restored without losing aesthetic type and functional characteristics. Many, remembering the grandfather way, in the old manner resort to a twist lived and further winding the tape. However, thus maintaining the repair of the Internet cable is not permissible.
This method is well suited when cutting the power and devices power cable. Any twist lived twisted pair is an additional interference, loss of data packages that you can then feel when working (reduction of speed, communication breaks, etc.). By resorting to a twist, you pay an order of magnitude the data rate.
This article will describe the method of repairing the Internet cable when cutting on the site from the entrance to the apartment and before connecting the device. If you damaged or broke the connector, then you can read about its repair in a separate one.
This situation may occur with an antenna cable. Therefore, I recommend to get acquainted with the article dedicated.
Required tool
To repair a damaged twisted pair, we will need several tools:
Tool for stripping and trimming cable (stripper)
Stripper is needed to remove a certain piece of external insulation, as well as cut off the extension live. To remove the insulation can come and the knife. However, be extremely neat so as not to damage the integrity of the live.
Wiring Connector (Scale)
Scotch plots need as much as it should be combined.
Connectors crimping tools
If there is no such tool, you can do with simple pliers. However, as with a knife, you must be careful, otherwise you can damage or crush the connector.
Internet cable repair (phased actions)
To begin with, with the help of a stripper, we remove excess insulation to free the veins from it (about 2 centimeters). We break the pig pairs, for the further simplicity of their installation in the connector.
Now, alternately take the veins of the same colors from different pieces of the cable and insert until it stops into the connector openings. After that, we latch the t-shirt by pressing two fingers. Using a tool for crimping connectors, please adjust the flacks finally and then the veins are not accurate. This operation must be carried out in turn with all the veins.
As a result of the repair of the Internet wire, it turns out a small beam (as it looks, it seems in the figure below).
This place is recommended to wrap the tape for additional protection. But before completing I advise you to check your work and make sure that the Internet works. To do this, you need to insert a swirling twisted pair into the device connector through which the network is organized (stationary computer, laptop or router). If everything works without failures, you can safely protect the place of repair of the Internet cable.
I advise you to get acquainted with the article about. Such a need may occur if you are going to make a redevelopment in the room and the equipment will be transferred to another place.
If you like this article, then subscribe to the new and use, please connect buttons.
Plastic connector for connecting the Internet cable is a very fragile thing. Especially often, with a regular cable connection, a locking tongue of the connector breaks up to various devices. Such a breakdown leads to the fact that the detachable connection is not fixed, so the connector pops out from the slot at the slightest progress of the cable. Today I will tell you how to quickly correct the situation with two ordinary cable ties.
Important! This method should be considered as a temporary solution and is suitable exclusively for home use.
Required tool
In addition to two small cable screeds, the following tool will be required:- A sharp knife.
- Lubes.
- Pasal or special gun for tightening cable tie.
Connector Latch Repair Order
The device of the new tongue on the connector is performed in this order:
Now it remains to adjust the length of the tongue so that it takes it to the broken head of the connector and skipped at the expense of the free (lower) end.
Ready! Now you can use the connector by inserting it into the connector until it clicks.