How to replace broken glass in a door. How to insert glass into interior doors of various models. How to insert glass into the door yourself

Most often, the repair of interior doors is reduced to replacing broken glass. There are cases when you can change it yourself, but sometimes you have to contact a specialist. In this article, we will talk about when you can replace damaged glass yourself and how to do it correctly and quickly.

What are the types of glass for interior doors

lamination. During production, glass is poured into several layers, between which a special film is placed. The result is a durable material that does not crumble upon impact.
liquid filling. In this case, a special liquid resin is poured onto the glass, which hardens under the influence of UV rays. It is strong enough, but it costs less than the one obtained by lamination.

What to do if the glass is broken

Such an unpleasant situation can happen to anyone and, unfortunately, can lead to injury. First, you need to remove the debris from the floor so as not to damage your legs. And then you can take out the rest of the glass in the following way:

We put on thick rubber gloves so as not to injure our hands.
Using a screwdriver, we loosen the glazing beads (part that holds the glass).
We take out the fragments and wrap them in paper. We start with the large parts and then move on to the small ones.
We check the sealing tape for damage, if necessary, replace it with a new one.

Advice! It is best to wear shoes with solid soles so as not to injure your feet with small fragments. And after removing the glass remnants, vacuum the floor again.

After the remnants of the glass are removed, we take measurements to purchase a new one. You can call a glazier or measure it yourself with a tape measure. If the opening has a complex geometric shape, transfer the dimensions to tracing paper.

Attention! The glass must fit freely into the door. To do this, you need to reduce its size by 1-2 mm on each side.

How to replace the glass yourself

Usually the glass is fixed in the door stock using glazing beads (quarters). Then the replacement of the coating will be carried out as follows:

Using a chisel or a screwdriver, we pull the nails that hold the quarters out. Then we grab it with pliers and pull it out.

Attention! First, pull out the side felts, then the lower ones, and then the upper ones.

We remove the old gasket (if it is dry or torn), as well as traces of glue and old sealant.
We coat the bed for the glass sheet with window silicone or sealant.
We insert the purchased glass into the canvas.

Advice! The glass should not fit tightly into the gasket; it is better to cut it.

We install felts, adjust them to size, and then fix them with decorative nails.

Advice! If you bought ordinary glass and want to get a decorative texture, you can stick a special film. First you need to moisten the glass with soapy water and carefully stick the film, carefully removing all the air so that there are no bubbles.

How to change glass in monolithic doors

There are door models on which glass is attached without the use of spatulas. In this case, you will have to disassemble the door, according to the following scheme:

Remove the door from its hinges and place it on a flat surface.
We remove the plugs and unscrew the fasteners
Now you can carefully remove the side of the door and remove the damaged glass.
We install a new glass sheet and close it back with a sidewall. If there is a problem with the seal that prevents the glass from rattling, moisten the edge of the glass with soapy water.

In conclusion, I would like to say that there are situations when replacing broken glass in an interior door on your own is impossible. For example, laminated glass must be replaced at the factory, just as broken material on PVC doors cannot be replaced.

Replacing broken glass: video

Do-it-yourself glass replacement in the door: photo

Replacing broken glass when renovating interior doors is a daunting task. There are many special nuances in it that must be carefully adhered to. If you make a mistake, then it will be possible to correct it only with the purchase of a new glass.

To prevent this from happening, you need to know about all the small details when repairing glass doors. The design and material of the door leaves are also important. Of course, repair specialists do not advise everyone to take on such work. There are only two reasons for this:

The complexity of the door design. Modern design developments offer very complex options. Not everyone will be able to deal with them. But the first step is to understand how the glass is fixed.
New technologies. Even the repair technicians are not familiar with all the new products. Each model can have unique qualities. In this case, you should only contact the master for reconstruction.

In principle, the main problems in replacing glass in interior doors are associated precisely with the complexity and unusualness of modern design solutions. When it comes to a simple apartment with no frills, then there are no particular difficulties in replacing a transparent element.

To carry out the process of reconstruction and replacement of glass in the door, it is worthwhile to carry out detailed preparation. The first step is to find out about the required materials. It is important to remember that glass is nothing special and there are many ways to replace it.

Currently, a large number of options are presented that are offered for interior decoration. Among them, some methods of glazing interior doors can be distinguished:

Use of decorative glass. This option is the most expensive of all. Few manufacturers use this insert in their products. Decorative glass can be safely considered ideal. However, the best examples also have minuses. In this case, we can highlight the uniqueness and rarity. If the glass is broken on one sash, it will be very difficult to find an identical option.
Plain glass. The most common and frequently encountered option. However, due to its excessive simplicity and low price, it requires additional work. So, there is a need for pasting glass with various films. On average, the cost is 2 times less than the decorative analogue.
Organic glass. No matter how beautiful and aesthetic glass inserts are, they have their main drawback - fragility. The use of plexiglass completely neutralizes this problem. In essence, such a material can be called transparent plastic. Its only problem is its susceptibility to scratches.
Fiberboard or plywood. A budget option for replacing glass in the door can be the use of laminated fiberboard. It is also possible to paste over it with a special film. However, this option will become very unaesthetic and unattractive.

Read how to repair an interior door yourself. How to repair an entrance door? Useful information in this article.

The standard way to install glass in the door

In most cases, the repair of interior doors with glass using quarters is very simple. A common mistake is to confuse them with glazing beads, but in some cases they can really be called that. However, this is not as important as the fact that fixing a door with this design is quick and easy.

And the process itself involves the following stages:

In the beginning, you will need, using tools like a chisel, to slightly undermine the quarters. The main purpose of this is to push the holding studs outward.
The next step involves extracting the nails with pliers. In this case, the sequence of removing the quarters must not be violated. If this is done, the glass can fall out at any time and break. Initially, you need to remove the side glazing beads, then the lower one, and at the end, the remaining upper one. It is during the last step that you need to be especially vigilant.
Dimensions. It is worth making measurements that will allow you to choose the right glass.
Installation. The process involves only inserting into the door and fixing glazing beads. That is, no peculiarities - just repeating the withdrawal in the reverse order.
Installation of glass. When it comes to opting for regular glass, extra effort is required. For the process to be successful, you need to moisten the glass surface with soapy water. When gluing, it is important not to forget to smooth the film. After that, you can install the element in the door and fasten it in quarters.

It is important to be especially careful when removing nails. In the absence of concentration, it is possible to damage the door surface, which will entail the need for additional repairs.

Replacing glass in an interior door is not considered a particularly difficult task, but it must be done accurately and accurately. A fragile insert requires skills in handling the material and the appropriate tools, so it is better to order cutting from a specialist. Trade construction organizations provide such services directly with the purchase of glass decor.

Glass inserts are most often changed for the following reasons:

The broken glass must be removed, even if it has not fallen out. A sudden movement when closing the web will lead to possible injury to people.
The aging of decorative inserts affects their appearance and also often leads to replacement.
Installing glass doors in your living room is an easy way to freshen up your interior. The repair option only includes replacing the glass in the canvas or resizing the frame.
The glass insert can be accidentally stained or scratched. You can replace the glass if it's easier than tidying it up.

Preliminary stage

To repair a damaged glass panel door, it is necessary to carry out preparatory work. Before installing a new insert:

remove protruding fragments from the frame (most often they are easy to remove with a little effort);
remove the canvas from the hinges and lay it on a flat surface;
inspect the door and try to determine how the insert is mounted;
if the glass is not broken, then dismantle it.

In old apartments, glass was inserted into the door frame using putty. To repair interior doors and replace broken glass, you need to pry off the glazing bead holding the insert with a knife or screwdriver. After that, pull out the nails with pliers, remove the glass part and clean the opening from the remnants of paint and putty.

To work, you need to prepare tools:

glass cutter;
hammer;
small nails;
silicone sealant.

Glazing beads often need to be replaced. You can buy them in a hardware store, in the lumber department.

Views

Doors are glazed using different types of material:

transparent - often supplemented by pasting with decorative films with drawings imitating a stained glass window;
matte - rarely requires additional finishing;
with a pattern, corrugated and stained glass - are decorative types of glass, it is better to entrust cutting them to specialists;
tinted or mirrored.

Selection of material

Frosted or corrugated glass is used where it is undesirable to view the room from the outside: in the bathroom, bathroom, bedroom. These types of material are thicker than transparent glass: it reaches 4-6 mm. The home craftsman will not always be able to cope with cutting on his own. Therefore, after dismantling the old glass, it is recommended to remove the dimensions of the opening for the insert and order a replacement in the workshop of the construction company.

For the living room, decorative glass for doors is more often selected: with an engraved pattern made using complex technology and surface treatment with a sandblasting unit, stained glass, consisting of colored pieces connected together. If desired, you can use both corrugated and frosted glass, if the interior design is not particularly luxurious or is made in a minimalist style.

Transparent and any other can be installed in the kitchen. A budget option is a simple window glass covered with a film, or decorative curtains on a glazed structure.

Options what can be replaced

If it is not possible to quickly insert decorative glass into the door instead of the broken one, there is an option to replace it with other materials. For temporary insertion, you can use:

plywood or fiberboard, covered with a film that fits the veneer surface of the canvas;
plexiglass (monolithic polycarbonate);
window glass covered with a film for stained glass.

These materials are not the best decor for the door, therefore, in the future, you will again have to make repairs and insert new glass into the opening.

How to replace glass in an interior door

In economy-class doors, the insert is removed and installed from above, through a special groove. Silicone sealant serves as a sealant: do not forget to clean the frame well from its residues. Before replacing the glass part, you need to find out its dimensions.

Glass in inexpensive models has a rectangular shape, so it is enough to determine the dimensions of the glass opening in width and length. When taking measurements, it is important not to forget about the allowances that are needed to fix the insert in the grooves. Measuring the allowance is simple: slide the ruler into the groove. Add the resulting value to the length and width of the opening.

It is advisable to cut the glass as accurately as possible so that it easily fits into the mounting gaps. Before installing the glass in the interior door, fill the grooves with sealant.

Doors of a more complex design will have to be disassembled to replace the glass. To do this, you need to find bolts on the sides, covered with special decorative plugs. By unscrewing the bolts, you can remove part of the blade and remove the insert. Measurements should be made taking into account allowances.

When inserting glass into a kitchen door with a panel, the master must find the dowels in the upper and lower parts of the canvas. They need to be removed and 1 side of the frame removed. Pull the glass panel out of the groove, measure and cut out the replacement part. Assemble the structure in reverse order. Place the dowels on glue.

How to insert rectangular glass

Rectangular inserts can be found in the interior or kitchen doors of old apartments, and in expensive products in new buildings. It is not difficult to insert glass into an old-style door:

after dismantling the glazing bead and cleaning the grooves, measure the opening taking into account the groove;
cut a rectangle to size and insert it into the opening, applying a little sealant there;
install the glazing bead in place and secure with nails.

Inexpensive plastic, laminated and veneered products are available with inserts on fasteners with glazing beads. In this case, the repair is carried out as indicated for the old-style doors, removing the strips along the perimeter of the opening on only one side of the door. It is advisable to save the nails with which the glazing beads are attached and use when installing the strips in place. To exclude the rattling of the newly inserted glass, before the procedure, apply silicone sealant to the recess between the canvas and the strips.

Variants of complex doors sometimes include non-removable fasteners: a groove with countersunk wedges. Such a product will have to be taken to the workshop for a branded replacement: it is impossible to do this with your own hands. According to user reviews, repairing a complex structure with hidden fixation is more expensive than buying another door, so it makes sense to ask a sales assistant for details in advance.

Installation of non-standard forms yourself

Manufacturers produce unusual models of doors with complex glass shapes. They are beautiful, but repairing them will not be complete without the help of a specialist. Do-it-yourself glass replacement in an interior door should be started by inspecting the fastening of the insert: if it is too complicated, then you should immediately call the master at home. But in the presence of removable elements, as a rule, you can replace the insert yourself:

Remove the door from its hinges and place it on a piece of cardboard. Its size must be sufficient to completely close the opening.
Delineate the contour of the opening as precisely as possible, do not forget to take into account the allowances for installation.
The template must be cut and tried on in the opening. It must fit exactly the size of the frame.
The template for glass with complex shapes must be taken to a cutting workshop.
It remains to put the finished parts into the grooves, coated with sealant, and secure with decorative overlays.

In sliding structures

A sliding door can consist of a large glass sheet and a thin frame around the perimeter, or look like a swing door: with inserts in a wooden or plastic panel. In any case, the canvas must be removed from the awnings and laid on the floor. To remove a heavy object from the grooves of the profile for sliding the sash, you will need an assistant.

If the door consists of a frame and glass, then you will need to disassemble it completely. Bolts can be found at the edge of the framing structure and removed. The edge of the glass is protected by a silicone seal, which must be removed and preserved if not damaged. If the integrity of the material is violated, it is ordered together with a glass door.

Measure the length and width of the web. It does not shatter into fragments, but only becomes covered with cracks, so it is easy to cope with the task. When ordering glass in a workshop, it is necessary to clarify that a material with a protective film (or triplex, as for car windows) is required. After receiving the ordered product, it remains to insert it into the frame, first putting the seal on the edges. When installing, cut the silicone tape so that it is 5 mm less than the glass on each side.

When installing a glass element between MDF panels, the fabric is collected on a horizontal surface. To install glass, overlays are most often used, which are attached to nails. When installing the insert and driving small fasteners into a wooden door, you must be careful not to break the glass: one wrong movement will lead to repeated repairs. Lift the assembled door leaf and place it in the sliding door profile runners.

When replacing glass in an interior door, you should follow basic safety rules Interior doors are often decorated with various glass inserts. It looks very nice and stylish. But it so happens that the glass is broken or damaged in some other way, which leads to the need to replace it. It is quite possible to insert new material with your own hands, without resorting to the services of specialists. To do this, you need to have the necessary tools and observe safety measures.

Options: how can you replace the glass in the interior door

When replacing broken glass, the question arises: what other materials can you use? Modern technology now offers many options that you can take advantage of.

Before you buy a new glass for an interior door, you should take measurements using a tape measure

So, what can be used to replace a broken glass surface:

Organic glass - its main advantage is that it is very difficult to break it. True, you can scratch. Even so, the material simply becomes cloudy. If desired, you can paste over the plexiglass with a decorative film, which will perform not only an aesthetic function, but also protect the material from scratches.
Decorative glass is one of the most expensive and stylish options. Its disadvantage can only be in the problem of finding the material with the desired pattern, otherwise all the glasses will have to be changed.
Simple glass - everything is simple here. The required dimensions are removed, the order is made to the glazier, and then the installation takes place.
Plywood or fiberboard is a temporary, budget option. The hole can be closed with a double-folded sheet of fiberboard, which is then pasted over with decorative foil. But all the same, there is no need to expect special aesthetics and durability from such a replacement.

Using any of these options, you can safely change the broken glass surface in the interior door.

Moreover, if desired, you can additionally darken the glass or glue any decorative inserts on its surface.

Replacing glass in the door: preliminary stage

After you decide what material will be used to replace the glass, you can proceed directly to the process itself. There is nothing complicated here.

To make it easier to change the glass in the door, it can be removed from the hinges

However, before starting the repair, some steps should be taken:

Remove the door and place it on any flat surface. As a rule, for this it is enough to lift and twist it a little, freeing it from the loops.
Remove the shards if there are still any. This should be done very carefully and preferably with rubber gloves so as not to get hurt.
Remove the gasket in which the previous glass was located, and also clean the door from putty or sealant.
Clean the stock with sandpaper.
Take measurements. If the glass is of the correct or simple enough shape, then it will not be difficult to do this.
Order new glass from a glazier or cut it yourself.

Be aware that new glass should not fit snugly into the grooves. This means that when calculating the dimensions, it should be 15-20 mm smaller on all sides than the bed itself.

How to insert glass into the door yourself

After all the necessary measurements have been made, the glass is purchased or made to order, you can proceed directly to the installation itself.

You can cut an opening for glass in an interior door using an electric jigsaw

Installation of a glass surface in an interior door looks like this:

Silicone sealant is applied around the entire perimeter of the hole;
The new glass is inserted into the gasket and put in place;
The sealant is applied again, only on the other side;
The glazing beads are twisted, which should then be fixed with special decorative carnations;
Then you need to wait one to two hours until the sealant dries, after which you can hang the door in its place.

If the glass goes very tight, you do not need to put too much force to put it down, otherwise you can damage it. It is better in this case to slightly cut the gasket.

When inserting new glass, various sealants can only be used if approved by the manufacturer. In other situations, it is better to do without them.

Sometimes it happens that the type of door structures is a solid sheet made of glass and wood (for example, MDF) without the use of glazing beads or any other improvised means. What, then, to do? In this situation, the doors can be completely disassembled in order to replace the glass that is broken or damaged in some other way.

To disassemble the interior door, it is worth using a screwdriver and other necessary tools.

This is how the process looks like:

First, the door leaf is examined for the presence of special plugs. It is they who often hide various fasteners under them (as a rule, these are self-tapping screws).
Further, the structure can be removed from the door hinges and placed on the floor or other solid and level surface.
Then all the plugs found must be carefully pulled out and unscrewed. Moreover, it is not necessary to do this from both sides.
After the fasteners and plugs have been removed, one of the door sidewalls is removed, followed by the glass surface.
Next, a new glass is inserted, and then the process of assembling the structure in the reverse order.

In case of any problems with the seals, a small amount of soap solution can be applied to the edges of the glass and thus facilitate its entry.

How to properly change the glass in the interior door (video)

Replacing glass in an interior door is not as difficult as you might think. This whole process is quite feasible on our own with the availability of time and tools. The main thing is to accurately remove the required dimensions, not forgetting to be careful when working. When choosing a new glass surface, you need to take into account its properties and the general design of the room, so that everything looks beautiful and harmonious.

An interior door that does not perform a protective function, unlike an entrance door, belongs to the functional part of the room, it is considered a rather significant element of the attribute. Models with glass inserts add light to the room, give harmony to any interior. It happens that the glass breaks, and the owner is faced with the question of whether the damaged door element needs to be replaced and how to do it. This article has detailed answers to these questions.

Professionals do not recommend doing glass replacement with your own hands, if there are no certain skills in working with similar materials. In the absence of knowledge of the technology of modern repair, the door deteriorates even more. This especially applies to stained glass, triplex and printed glass, which are fragile and costly.

However, armed with the necessary tools, having familiarized yourself with the safety precautions, it is possible to eliminate the trouble, but with a small nuance - it is unlikely that it will be possible to find the same, since the manufacturer does not provide for the distribution of components to door models.

But do not be upset, broken glass is replaced with other elements from alternative materials. The main thing is to find out the design features of the interior door and get acquainted with the specifics of its production, since a fragile part requires careful handling.

If you still manage to find a similar one, cutting is best done at trade construction organizations, providing such services after purchasing glass decor.

In general, replacing broken glass decor is not difficult.

Causes of damage to glass inserts

In fact, the interior modern door is quite strong, but there are several factors that contribute to damage to the glass inserts:

Poor quality material. Usually, the manufacturer uses rather durable glass, which additionally serves as decorated inserts. But it happens that a material made not in accordance with the technological process becomes fragile and vulnerable, and becomes unusable at the slightest impact.
Careless handling. Sometimes the door is subjected to a sharp bang, as a result of which the glass breaks. This happens most often in families with small children. They can also deteriorate after contact with animals that like to close the door with their paws, which is why it slams hard.

Required tools

Before putting new glass in the door structure, tools are prepared in advance, which will be needed in the process. These include:

Hammer. It will be needed for driving the nails and adjusting the position of the glazing bead. A special furniture or rubberized hammer is suitable for work, which does not damage the material.
Screws 3 cm and screwdriver.
Ruler or tape measure.
Fine-grained sandpaper.
Pliers.
Construction knife.
Glass cutter.
Chisel. May be needed when replacing glass.
Gloves. Help protect your hands from cuts.
Scoop and broom. In order to collect the broken old glass and remove the debris left after the installation of the new one.

What to use?

Of course, interior doors with glass inserts look spectacular and stylish, but due to the fragility of the material, situations often happen when a decorative element needs to be replaced. Owners prefer to replace the part with a similar one, waste a lot of time looking for a suitable element, but this is not always possible.

If the search for a similar part is not successful, ordinary glass, frosted or any other, is replaced with one of the alternative materials produced according to modern technologies.

Fiberboard sheet

As a temporary and budget option, laminated fiberboard folded in half is suitable so that the smooth side is outside. Or an ordinary, non-laminated type of fiberboard, on the front surface of which an opaque decorative film is then applied. This method is considered the least aesthetically pleasing and short-lived, therefore it most often serves as a temporary way to hide the missing glass element in the overall door structure.

Decorative film

If the glass is cracked, but not crumbled, as well as with small chips, all parts of the structure are pasted over with a decorative film. Thus, not only defects are hidden, but also integrity, harmony of the appearance of the door structure is achieved.

Stained glass insert

Refers to the most expensive materials used by manufacturers in the manufacture of interior doors. Such glass adds style and originality to the door, it is quite durable and does not require additional work material. The only drawback is the difficulty in finding a part with a similar decor, so you will have to change all parts, which translates into a significant amount.

The usual

Transparent material without additional decoration for an affordable price is considered one of the most suitable for replacing a burst element. After taking measurements, the glass is ordered from the glazier, inserted in place of the damaged element. If you have the necessary tools, glass cutter, for example, cutting and cutting are performed independently. Then the surface is decorated with a special film or any other suitable material.

Organic

In other words, it is a transparent plastic that resembles glass in appearance. It is also called monolithic polycarbonate, a durable, unbreakable material, the only drawback of which is the clouding of the structure. This is due to the appearance of scratches on the surface of the material. To protect plexiglass or to hide flaws that have already appeared, applying a decorative film will help, which will additionally serve as a decoration for the door.

Hardened

Ordinary glass, made using a special technology, which has undergone heat treatment, which gives the material not only increased strength, but also fire safety, noise insulation.

How to disassemble the structure?

Before replacing your cracked or broken decor, you need to know how to disassemble the door. To do this, perform a number of actions:

Remove the door from the hinges so that the process of replacing the insert takes place as safely as possible. To do this, they lift it up and shake it in different directions.
Lay it on any level surface on a dais, such as a table or chairs pushed together.
It is better to cover the floor under the structure with an old cloth to avoid damage in case of unforeseen situations.
Inspect the method of attaching the glass to the door leaf, as well as the design principle of the door itself.

If the decor is fixed with glazing beads, during repair they are pushed aside with a chisel, knife or screwdriver, the broken insert is pulled out through the top, starting with large fragments, then small parts are removed. Next, measurements are taken, a new element is selected, inserted and fixed in the same way, but in reverse order.

To replace a damaged insert in interior door models where the glass is connected to the leaf without the use of glazing beads, disassemble the door in the following order:

Remove the door from its hinges and place it on a horizontal, solid surface.
Check the door structure for all kinds of plugs, behind which fasteners, such as self-tapping screws, are usually hidden.
Unscrew the plugs and unscrew the self-tapping screws on one side of the door.
Pull out one of the door sides, free the cavity of the door structure from debris. If the glass is cracked but intact, remove it.
Measure the damaged material, given that the size of the new glass is 1.5-2 cm less than the stock.
Get rid of the old gasket, glue residues, sealant. Sand the canvas with fine sandpaper.

How to use: materials needed

Prepare materials in advance that will be useful in the process of replacing decorative glass, having previously found out in what way the element is attached to the door:

Glue. To securely attach the insert to the sheet, glue is often used by applying it to the edges of the glass sheet.
Rubber compressor. Useful for filling too wide gaps between glass and door.
Sealant. The elastic substance is useful for covering crevices, depressions and joints. Also, the tool is used when installing new glass for applying to the surface of the installed canvas and glazing beads.
Small nails. They are used to fix the glazing bead to the door leaf. It is considered the most reliable and common option.
Glazing beads and other fastening materials.
Sealing paper. Useful to adjust the dimensions to the design of the canvas.

Attention

The list of tools and materials that will be needed for repair work may differ depending on the type of material, as well as the design features of the interior door.

How to install?

After the door is prepared, the old damaged glass is removed, they proceed to further replacement steps. Depending on the shape and door structure, there are several options for replacing the insert.

Replacing the rectangular decor in a standard veneer door is easy. It is not necessary to disassemble the door for this, usually the glass sheet in such models is inserted through the upper end. The prepared, sized material is lubricated around the perimeter with silicone gel for secure fixation, lowered into the door leaf through the upper part.
If the insert was attached with glazing beads, a chisel or a flat screwdriver, the quarters are removed, observing the sequence: first, the side parts are dismantled, then the lower one. Next, measurements are taken from the broken part, a one-to-one analogue is prepared, put in place, fixed in quarters in reverse order. If the glass has not crumbled, a decorative film is applied. Further, the glazing beads are fixed with carnations.
A non-standard type of canvas, in which the sashes are glued together, and not fastened with self-tapping screws hidden behind plugs on the side, as in the standard design, requires a slightly different approach. To replace the damaged element, the door is disassembled. How to do this is described above. When the damaged glass is removed, measurements are taken, an analog is made and inserted into place.
In premium models, it is better to entrust the replacement of the insert to professionals, since the canvas has a collapsible design. To remove the broken glass, you will have to completely disassemble the structure, after replacing the insert, reassemble it. The process is quite laborious, requiring increased attention and caution. However, having understood the principle of assembling a particular model, the replacement is performed independently.
If the insert is made in a unique design style, has an oval shape or resembles a wave, the fragments are removed from the door cavity, the canvas is laid on cardboard spread on the floor, and is outlined with a marker. According to the measurements obtained, the workpiece is ordered in the workshop, then a replacement is performed.
Doors, in which glass is inserted instead of a panel, are easy to disassemble. The vertical and transverse beams are connected according to the “tongue-and-groove” principle, in order to get to the glass it is enough to open the lock and remove the insert. Then replace the damaged part, reassemble the door in reverse order.
The broken glass in the sliding door is changed after the door leaf is dismantled, the metal frame is removed. The method of inserting the glass element may differ, after understanding it, they are replaced according to the design features.
In addition to the standard interior door, today there are often side-by-side models in which the glass insert is also susceptible to damage. The door leaf in such models contains reinforcing bars, with the help of which the structure itself is securely fixed in the opening, which adds rigidity and strength to it. To change the insert, remove it, unscrew the plugs, unscrew the bolts from the inside of the hinges, and put it on the floor or on a long table.
Next, proceed to remove the remaining plugs along the edges of the canvas. Starting from the location of the fasteners, the drawer side is separated from the canvas by moving from the bottom up with the help of a wooden block and a hammer. Having disconnected the beam, remove the broken glass from the groove together with the rubber seal, measurements are taken, a new one is purchased, and a replacement is performed. The actions are carried out in the reverse order, observing caution and accuracy.

We offer you to watch a video on how to replace glass in an interior door:

Replacing a broken insert is a responsible and time-consuming business that requires adherence to a sequence of actions that take into account the features of the selected materials, as well as the door structure itself. Experts share their advice with those owners who decided to get rid of the unpresentable appearance of the interior door on their own.

To remove the broken glass, it is not necessary to completely remove the glazing beads holding it. It is enough to loosen the quarters with a screwdriver or a construction knife, bend to the side, remove the fragments, and only then remove the fasteners.
Before replacement, the complexity of the work is assessed, some designs are unique, have non-standard dimensions, so they are assembled in production. These include, for example, triplexes.
If, after replacement, large gaps have formed between the blade and the insert, pieces of cork are placed in the gap, filled with sealant or liquid glue.
A small crack that appears does not always require a complete replacement of the insert. It is enough to glue the area with special glue or "epoxy", apply molding or decorative film.
Matches, which are installed in the corners of the grooves and also "sit" on silicone glue, will help to fix the loose insert.
When removing the glass, you should use rubberized gloves so as not to injure your hands.
If it is not possible to remove the door, it is completely opened, the lower part is securely fixed. But this method is more suitable for standard veneer models, in which the inserts are fixed in quarters.
The renewed door leaf is left in a stationary position for several hours to allow the adhesives to harden and to fix the internal structure.
To safely remove the broken material, the top beads are removed first.
Regardless of how strong, at first glance, the adhesion between the insert and the canvas seems to be, the fixation is completed by installing glazing beads. They are nailed down with finishing decorative carnations using a special carpenter's hammer.
Do not use too much force when inserting new glass if it fits tightly into the groove. It is better to undercut the gasket a little, otherwise you may damage the material.
Before cutting, the glass is heated to room temperature, then washed with soapy water, wiped with a cotton cloth. Thus, the material becomes less brittle and does not crumble during cutting.

Replacing the insert with your own hands is a laborious process, but quite feasible. The main thing is to understand the design of the interior door, the features of the fastening of individual elements. An important condition is the correctly selected alternative material, as well as compliance with the above rules.