Ceramic tiles on drywall in the bathroom. How to sheathe the walls in the bathroom with plasterboard, which will be finished with tiles: the thickness of the gypsum board, the progress of work in stages. An alternative option for attaching drywall

Installing tiles in the bathroom on drywall with your own hands. is one of the most popular materials for sheathing walls in any room. It has many advantages, and one of them is low cost and ease of use. True, the choice of what material will be used to decorate the gypsum plasterboard is not easy, since the material is made of pressed gypsum and crushed waste paper, which is "afraid" of excessive moisture.

This is especially true when it comes to finishing the sanitary unit, since tiles are often chosen for it, which have certain styling features. Below you will learn how to lay tiles on drywall in the bathroom and what to consider during the work.

General information

How to choose drywall for tile installation

Modern manufacturers offer not one, but several varieties of drywall boards that can be used to level the walls in a room.

GKL.It is used for redevelopment and renovation work in rooms where the humidity level is low.
GKLV. The material is made using a special impregnation that helps protect against moisture.

In order to lay the tiles in the bathroom, it is better to choose the second option, since it is resistant to moisture and will not deform from interaction with water. The use of a standard material sometimes leads to the fact that the finish becomes unusable. Sometimes the gypsum board is used for the base of the tiles, but before starting all the work, you should make sure that the ventilation in the room is in order and works as required.

Important!A material that is resistant to moisture can also be distinguished by its appearance, as manufacturers mark it in green.

How to choose a tile adhesive

The second important point that should be considered for laying tiles on drywall sheets is the selection of an adhesive composition. From the assortment that is presented in stores, it is recommended to use mixtures made on the basis of cement, elastic glue, and also liquid nails.

Adhesive mixtures for laying are produced by the following manufacturing companies:

When you decide on the glue, you can start choosing the finishing material directly.

How to choose a tile that is suitable for drywall

Any tile is suitable for laying tiles on drywall in the bathroom, but you should still take into account some features that will help affect the final result.

Appearance.The surface of the material that will lie on the plasterboard surface should not be chipped, as well as fuzzy or smeared with ornaments, stains or abstract objects. The best option would be a tile of a monochromatic type or clear patterns.
The evenness of the material. It is recommended to glue tiles on drywall, which have a perfectly flat surface. This factor can be checked by folding all the tiles face-down and evaluating the tightness, as well as the width of the gaps. The corners of the products should be perfectly even.
The hardness of the material. So that the tile is not deformed due to temperature extremes, only solid specimens should be selected. It is impossible to visually check such a characteristic, but you can slightly hit the surface of the tile - if the material is of high quality, then the sound will be dull.
The size. The best option for laying will be tiles of standard sizes, the side length should not be more than 33 cm. In this case, the load on the plates will be evenly distributed, and the elements will be held very securely.

Please note that it is better to buy tiles with a margin, while the number of tiles should be about 20% more than required by calculations.

Note,that both ceramic and plastic tiles are suitable for laying on drywall, but it should be borne in mind that although plastic products will be cheaper, they will also last much less.

Step-by-step instructions for cladding

Tiling is a fairly simple but time-consuming process that requires compliance with a number of conditions.

As mentioned above, first of all, before tiling with tiles on drywall in the bathroom, you will need to sheathe the bathroom walls with gypsum plasterboard. This is done according to the standard, but there is a nuance that should be taken into account - a large load will fall on the surface, so the frame must be strong, and it should be reinforced with horizontal elements (racks). This is extremely important in spacious rooms, since the tiles will begin to deform or even peel off from constant vibration.

There are several types of profile that should be used to strengthen the drywall frame:

Regardless of the width of the profile, it is better to use one that will be made of metal sheets, the width of which is not less than 0.06 cm. The frame elements should be at least 0.4 meters behind each other, and the sheets should be laid in two layers. So your frame will not bend under the weight of the tiles, and the seams between them will not diverge due to the influence of negative factors.

Important!If it is not possible to sheathe the walls in two layers (for small bathrooms this will "steal" a large amount of usable space), you can use another method. To do this, glue the walls between the intervals of the profile elements using a plaster mesh, which will be fixed with brackets. After such work is completed, you can lay the tiles on sheets of drywall and not worry about the fact that everything will come off or deform as a result. Some of the specialists use a metal profile and a reinforcing mesh for reinforcement.

Preparation of materials and tools

To lay tiles on a drywall surface, you will need the following tools:

Spatulas.
Building level.
Tile cutter.
Paint roller or brush.
A drill with a nozzle that helps to mix the adhesive.
Special crosses for aligning seams.
Fine grit sandpaper.

It is better to use a primer and putty as an additional material for the work. For work with drywall, a cement-based or polymer-type putty is ideal. Cement putties, although cheaper, have one drawback - they give little shrinkage after drying. Polymer-based compositions are distinguished by their high cost, but at the same time they have excellent performance characteristics - strength, high resistance to moisture, no shrinkage.

Primeris another equally important material, which is difficult to do without when laying ceramic tiles on sheets. the best option would be to use water-repellent compounds for bathrooms that will protect the cladding from moisture.

Certain products contain antiseptics that help prevent mold and mildew on the walls. It is equally important to pay attention to the fact that there are no toxic substances in the primer - for interior work on laying tiles in the bathroom on drywall with your own hands, it is better to use acrylic mixtures that are 100% safe for human health. Almost all other compounds, such as aclide and phenolic, contain toxic substances, so they can only be used for outdoor work.

Note,that when choosing a primer and putty, attention should be paid to ensure that they are compatible with each other, therefore it is better to focus on products from one manufacturer.

Surface preparation

So, in order to prepare the surface for laying the tiles, you will need to apply putty on the drywall, and then a primer. You cannot do without this, since otherwise the tile will begin to peel off under the influence of negative factors.

Remove the chamfer, clean the drywall well from dust.
Thoroughly process all joints with putty so that you get an excellent monolithic construction as a result.
Next, we apply a reinforcing tape to the treated seams, and on top of it a layer of putty should also be applied. The excess must be removed with a spatula.
Wait for the mixture to dry and sand the seams with fine-grained sandpaper.
Apply the last layer of the composition, wait until everything is completely dry, and then sand it again.
After the putty is completely dry, you can proceed to applying the primer. It should be applied with a brush or paint roller and in 2 layers, each of them should dry (at least 45 minutes).

After the primer has dried, the walls must be flat and have a solid surface on which the tiles will be laid.

Important!All technological holes that are required for communications are required for processing along the contour with silicone sealant so that moisture does not accumulate in these places.

Performing preliminary marking

Drawing up a scheme for laying tiles and marking is required so that the final appearance of the cladding is aesthetic, and the amount of waste and scrap is minimal.

In order for the horizontal rows of tiles to be placed correctly, the zero level must be determined. To do this, put a point in one corner, and it should be transferred to the other corners, while the distance and evenness of the lines must be checked using a building level. On the resulting line, you can draw a marking, which will be an excellent guideline for laying a horizontal row. The rows that will go vertically should be marked from above - in this case, the tile that needs to be cut will be below and will not be so noticeable.

To determine which part of the wall is best to start working on, measure the length of the surface and divide by the width of the tile. If the number in the remainder is more than half the width of the tile, then we recommend starting the cladding from the part of the surface that is most noticeable - due to this, the cut off part will be almost invisible. If the remainder is less, then it is better to lay the tiles from the center of the wall so that the elements of the row cut off at both ends are the same, and the laying is symmetrical.

After all measurements have been made, mark the line on which the bottom row of solid slabs will be located. After the preparatory stage, it will be necessary to fix a wooden strip along it, which will become a support for the tile until the glue mixture begins to harden (otherwise, the tiles from the lower row will be able to slide under the weight of the upper ones).

Laying tiles

So, we have come to the most important stage - gluing the tiles in the bathroom to the drywall walls. Such a process will practically not differ from laying tiles on other surfaces - the most important thing in this case is the careful implementation of all the nuances and accuracy. Particular care must be taken when cutting the elements, and in order to separate the desired part of the tile, you will need to run a tile cutter over it, and then gently hit the hard part with it. As a result, the tile will split into pieces and have smooth edges.

Attach a metal or wood strip at the height where the first row of solid tiles will be located.
If dry adhesive will be used for laying tiles, if it should be diluted in the way described in the instructions. It is better not to make a lot of glue at once, as the mixture is able to quickly "set" and after a while will become unsuitable for work - it is better to focus on the amount of glue that will be required to lay 1 m 2 of tiles.

Important!To get an excellent result, you must choose the right consistency of the adhesive mixture. Too liquid composition will flow down the wall, and a thick one will not work out evenly over the surface. The optimal consistency will be one that resembles thick sour cream.

The photo shows how to glue the mirror along with the tiles. Then repeat everything until the entire surface is covered. The composition will dry for at least a day, but proceed to the last stage - grouting, it is better not less than 3 days later.

Grouting

After the glue has completely hardened, the plastic crosses should be removed, the seams should be slightly cleaned with sandpaper and rubbed with a special mixture. The grout should be matched to the color of the tile, or by contrast, in order to obtain an original appearance of the surface. The grout mixture should be applied with a rubber spatula, and after half an hour, when it is well absorbed into the seams, you can mix the residues from the surface. Note that the grout will perform not only decorative functions, but will also protect the seams from the accumulation of dirt and moisture.

Cladding repair

If the tile on drywall in the bathroom is cracked during use, it can be easily replaced. To do this, you need to cut out the area with the cracked tiles so that you get a small hole. Then take a new profile, fix it on the wall with a hanger, cut the desired piece, close the hole and glue a new tile.

How to avoid mistakes when laying tiles on drywall sheets

In order for tiling from a tile on a drywall surface to be durable and reliable, you should avoid many of the mistakes that beginners often make.

Insufficiently good frame reinforcement. If you ignore this stage of work and do not use a reinforcing mesh or a metal profile, then the tile will quickly collapse and crumble.
Incorrectly selected adhesive, putty or primer, as well as mixing errors. If the materials do not combine with each other, or you made the mortar in the wrong proportion, the lining will begin to peel off even with little physical impact.
Incorrect application of the solution. The glue should be applied so that there are no voids between the tile and the wall, since otherwise the tiles may crack in those places (this is extremely important if the lining is on the floor). Moreover, make sure that the layer of mortar is as even as possible, otherwise the cladding will turn out to be wavy and the tiles, which will be higher than the rest on the surface, will begin to peel off in the future.
Any mechanical impact on the tile before the glue is completely dry is prohibited. It is best not to even touch the surface until the glue has set. If you do not do this, then at first imperceptible destruction will appear on the coating, and then they will begin to intensify, and because of this, you will have to redo the finish.
Poor seam work. Poor seam treatment with sandpaper and improper grouting will not only lead to a worse appearance, but also to the fact that moisture and dirt will begin to accumulate between the tiles.

Cladding with plastic or tile is the best option for any bathroom with plasterboard walls. If you follow all the rules and stages of finishing, then the coating will delight the eye for a long time and you will not need special care or constant repairs.

The use of drywall in construction makes it possible greatly simplify the solution of most problems in the field of repair... This also applies to laying tiles on drywall in the bathroom. Tiles on such material are placed without additional manipulation, in the form of alignment. Its surface has excellent adhesion, which allows tiles to be firmly and securely attached to it.

Pros and cons of tiles

Laying tiles on this material has a huge number of positive aspects, as it is the most versatile finishing material. The main ones are:

No need to align walls, due to the initially flat surface;
Possibility to put an additional layer of insulation under the surface of the drywall;
Easy to obtain material of the correct size and shape, for installation in corners or at joints;
Highly simple tiling process, which can be carried out even by a person who does not have construction experience;
Minimal waste of time to carry out all events.

The main and, probably, the only disadvantage of laying tiles on drywall is reduction in area premises due to the lathing.

Finishing features

The drywall itself in the bathroom must be mounted exclusively for metal profiles... The fact is that if wooden planks are installed, they will rot over time, a fungus will form on them, and as a result, a complete re-laying of the entire surface will be required. So that the material itself is protected from moisture, the edges of the gypsum board need to be smeared with mastic... Also, you can make a membrane from a thin layer of waterproofing.

For use in the bathroom, try to choose slabs that have a special hydrophobic impregnation. Otherwise, you can get the material swelling from moisture getting on it and falling off the tiles that will be on it.

Of course, any type of finish can be applied to the surface of drywall, but it is tile is the best option for rooms with high humidity... But due to the porous structure of the material, the surface must be treated with a primer before installing the plates. It should have a function to penetrate deep into the pore opening and have antifungal properties. It can be applied either with a regular brush or with a universal roller.

Adhesive selection

Apart from its basic properties, glue must be extremely elastic... This is necessary so that during the deformation of drywall and boards, it can withstand the resulting stress. Otherwise, the materials will crack and peel off. In total, when laying tiles in the bathroom, several types of glue are used, such as:

Drywall surface preparation

Before laying the tiles, using ordinary PVA glue, put on drywall sheets plaster meshmade of polypropylene. Despite the brand or manufacturer, the gypsum board must be treated with a primer. This will increase the strength of the tile to the surface. The mixture is applied using a notched trowel. Need to apply multiple layers, each of which is allowed to dry for at least an hour.

Gluing tiles on the surface of the gypsum board

To carry out this type of work, you need the following tools:

several spatulas, one should be with a flat surface, and the second with a ribbed;
building mixer or a drill with a suitable attachment;
tile cutter;
the container in which the glue solution will be located;
building level;
plastic crosses that will be placed on the seams.

The entire technology of laying tiles on drywall is divided into several stages:

Initially held counting the number of resulting rows of tiles horizontally... To do this, taking into account the gaps, roughly divide the wall by the width of the tiles to be installed. In the case when, when dividing, the remainder of the space is less than half of the length of one tile, installation must be carried out starting from the center... If it is more than 1/2 of the tile, then it is worth starting to fix the tile from the more visible side. This will make sure that the divided tile is in the least accessible place for the eyes;

Further stir the glue solution in a small container. This procedure must be carried out following the instructions from the manufacturer. It is not necessary to cook large quantities at once so that it does not freeze. For one preparation you need prepare the composition for about 1 square meter... Using a drill or a construction mixer, we prepare the glue so that its consistency is similar to sour cream. Before laying the tiles, below you need attach the railwhich will be the same width as the tile. Fastening must be done with dowels, I control the level, the correctness of its position;

Tile installation will start from the second row or from the center, or from one of the sides. The mortar is applied to the tile from the back side, no more than 1 cm thick. This can be done using a prepared notched trowel with the height of the teeth of the appropriate size. After fixing the first tile, first a vertical, then a horizontal row is made. Each seam formed between the tiles is sealed with mortar and special plastic crosses are inserted between them, which allow you to maintain the desired thickness;

When the glue hardens and the tile gains stability, it is necessary to clean its surface from the remnants of the glue mass and remove the crosses. After the surface is completely paved, return of seams with a special moisture-resistant compound... Having completed all the connections, we remove the resulting excess.

Drywall is a demanded building material used to perform a variety of finishing works. One of the areas of application of gypsum board is wall cladding in rooms for various purposes and humidity levels. The best option for further finishing drywall in the bathroom is tiling. This method has its advantages as well as technological nuances.

Of the advantages of laying tiles on drywall in the bathroom, the following aspects are distinguished:

Saving time and materials for wall preparation: the leveling function is performed by the gypsum board sheathing.
· Possibility of additional thermal insulation of the room due to the laying of insulation between the frame posts.
High speed of finishing works.
Minimum dust and debris during work.

The disadvantages of this technology for finishing bathrooms include the fact of reducing the usable area of \u200b\u200bthe room by creating a frame from a metal profile, which is necessary for fixing the gypsum board.

Choice of materials

To finish the bathroom with plasterboard tiles to be durable, you need to use high-quality materials and follow the technology. To complete the work, you will need the following materials.

Profile

The frame for fixing the gypsum board in the bathroom is best assembled from metal profiles, since a wooden bar, even treated with an antiseptic, begins to rot over time. The profile for plasterboard structures is made of galvanized steel. The frames assembled from a metal profile have a high bearing capacity, rigidity, they are reliable, durable and do not corrode.

When choosing a profile, you should pay attention to the following parameters.

The size

The rack profile, which is the main element of the frame structure, is produced in the following sizes: 50 × 50; 75 × 50; 100 × 50 mm. For the construction of the frame, a profile of any width is suitable, but at the joints of the sheets it is more convenient to use wide products to fix the edges of both sheets.

Metal thickness

Profiles are made with a wall thickness of 0.3; 0.4; 0.5 and 0.6 mm. The greater the thickness of the metal, the more rigid the structure is obtained and the higher its bearing capacity. But at the same time, the mass of the frame also increases. A profile with a thickness of 0.5 or 0.6 mm is considered optimal for the frame for tiling.

Manufacturer

While everything is clear with the profile thickness, the choice of manufacturer is a little more complicated. On the one hand, well-known brands adhere to SP 163.1325800.2014 regarding the requirements for profiles for gypsum plasterboard structures, undergo certification and guarantee the quality of their products, but they are most often counterfeited by unscrupulous manufacturers. Products of little-known manufacturers are cheaper, but there is a risk that the requirements of GOST 14918-80 in terms of thickness and quality of galvanized coating are not met, which will shorten the service life of the profiles in high humidity conditions.

Below is a list of some of the most well-known manufacturers of profiles for plasterboard systems:

Drywall or gypsum fiber

You can often hear that gypsum fiber (GVL) sheets are better for wet rooms instead of drywall. Let's take a quick look at the differences between these two materials.

Drywall

It is made of gypsum enclosed in a cardboard sheath (GOST 6266-97). For sheets intended for dry rooms, the cardboard is gray, for wet ones (moisture-resistant drywall) - green.

Moisture resistant plasterboard: white gypsum core and green cardboard sheath.

It is convenient to work with gypsum board: the material is easily cut, does not crumble during the cutting process, with careful work the sheets do not break.

Gypsum fiber

GVL is a board made of a compressed mixture of cellulose fibers with gypsum (GOST R 51829-2001). In addition to ordinary gypsum fiber sheets, moisture resistant (GVLV) are produced. Several manufacturers offer fiberglass-reinforced sheets that have improved strength and load-bearing characteristics.

It is more difficult to work with gypsum fiber board, the plates crumble during cutting, break quite often (corners are especially broken off), but the broken pieces can be mounted with sealing of the joints.

What to choose?

If you do not have the skills to work with gypsum fiber, then to perform wall cladding in the bathroom with your own hands, it is better to use moisture resistant drywall (GKLV). This material is easy to work with, and when sealed with a moisture-resistant grout, it can serve for a very long time.

Glue

There are 3 types of adhesives suitable for gluing tiles to drywall.

Mixes based on cement and sand

An outdated technology that is practically not used now. The reason for this is the strong shrinkage of the mortar during setting and drying, which leads to rapid peeling of the tiles. Plasticizers are added to the ready-made dry mixtures, due to which the plasticity and workability of the solution increases, and the shrinkage decreases. Such mixtures are used for gluing tiles if the budget is limited, since the price for them is lower than for other types of glue.

Glue in tubes can also be used for tile mounting. But if you need to glue a lot of tiles, then the cost of such finishing will be very high. Therefore, this option is acceptable if you need to make minor repairs, for example, glue the damaged tiles that have fallen off the base.

Liquid nails are ideal for spot repairs.

Tile adhesive mixtures

The best option is to use special adhesive mixtures for ceramic tiles. Such compositions have high adhesion to various substrates, elastic, plastic, easy to use. Ceresit tile adhesive is considered the leader in use. You can use CM 9 for interior use, CM 11 Plus (standard glue) or CM 14 Extra with reinforced adhesive properties, which is suitable for self-adhering porcelain stoneware tiles.

In addition to CM Ceresit, masters on specialized forums praise IVSIL FIX glue, an inexpensive, economical composition for interior work, as well as Knauf-Fliesen, designed specifically for gluing tiles to bases made of gypsum plasterboard, gypsum fiber board and other sheet materials.

Tile

Any type of ceramic wall tile is suitable for laying on gypsum board. The main criterion for choosing a tile is its appearance. Here you should be guided by personal preferences, as well as take into account the peculiarities of the bathroom interior and the general style of the house or apartment.

Tile size

The smaller the tile size, the more difficult it is to install, especially if there is not enough experience in such work. The standard size of wall tiles is 200 × 200 or 200 × 300 mm.

Note! According to GOST 6141-91, the permissible deviation of the dimensions of the tiles in length and width is ± 0.8%. In this case, the difference between the largest and smallest tiles from one batch should not exceed 1.5 mm.

Installation

Now we will consider in stages how to independently glue the tiles to drywall, taking into account that the wall cladding of the gypsum board has already been completed.

Tools

To work, you need the following tools:

Building level, tape measure and marker.
Tile cutter or grinder.
Spatulas with smooth and serrated edges.
Construction mixer or drill attachment for mixing dry mix.
Distance crosses for setting equal space between tiles.
Self-adhesive mesh (serpyanka).
Container for making glue.
Rubber spatula.
Moisture resistant joint grout.

You will also need a wide brush or roller and a primer.

Surface preparation

Preparation of plasterboard sheathing before gluing the tiles includes the following steps.

Sealing of seams

After finishing the wall cladding of the gypsum board, the seams between the sheets must be repaired with gypsum putty. This is done in the following order:

Padding

The next step is to apply a primer. A deeply penetrating primer with an antiseptic is used, which is applied in two layers with a wide brush or roller with an interval of 40 minutes.

Priming the drywall helps reduce the absorbency of the material and improves the adhesion of the adhesive.

The need for waterproofing

It is not necessary to waterproof drywall, since the tiles are waterproof and the seams are sealed with water-repellent grout. To increase the adhesion and reduce the absorbency of the gypsum board, a thin layer of ordinary tile glue, brought to a liquid state, is applied with a cloth. This re-priming will also act as a waterproofing seal. Good waterproofing is required only in showers and swimming pools.

The application of a liquid adhesive improves the adhesion of the tile to the substrate.

Note! When priming the walls with tile glue, the composition is also treated with 10-15 cm of the floor surface. At the junction of the drywall sheets, a waterproofing tape is glued to the floor, which is then covered with the same thinned adhesive.

Markup

To make the laid tile look attractive, several nuances must be taken into account when calculating the laying scheme:

It is best to cut the tiles in height at the bottom, near the floor: this way it will be less noticeable.
If the tile also needs to be trimmed in width (the whole tile in one of the corners is not included), then the installation starts from the freest corner, and it is best to trim in the corner cluttered with furniture. You can also calculate that the tiles will be trimmed on both sides of the wall, as well as above and below, by the same distance.

Two options for the tile laying scheme.

Horizontal lines are marked on the wall, indicating the rows of tiles: it will be easy to control the horizontal along them during installation.

On the lower edge of the bottom row of whole tiles, a wooden block or metal profile is fixed, which will act as a support so that the tile does not slip during installation until the glue sets.

Profile as support for the bottom row.

Glue preparation

To prepare tile glue from a dry mix, you will need a clean container and a construction mixer or a drill attachment. A measured amount of water is poured into the container, into which the dry mixture is gradually added (while mixing with a mixer should be continuous). Stirring is carried out until a homogeneous mass is obtained, but not less than 3 minutes. Then a technological break is made (about 5 minutes), after which the mixture is kneaded again for 1.5–2 minutes.

Important! Each manufacturer on the packaging indicates the proportions of the mixing, which must be strictly observed in order to obtain the glue with the optimal consistency and the required characteristics. For example, for mixing 25 kg of dry mixture Ceresit CM 11 Plus, the manufacturer recommends using about 6 liters of water, and 5 kg - about 1.2 liters.

Styling

The technology for gluing tiles to drywall is no different from laying it on other surfaces. But the advantage of pre-leveling the walls of the gypsum board is that the tiles are laid on a flat surface, which greatly simplifies the work and reduces the consumption of the adhesive mixture. Let's consider the main stages:

Advice! After laying several tiles, check them with a rule or level so that they lie in the same plane.

Grouting

The adhesive composition sets for at least a day. After this time, you can start grouting, but it is better to wait three days for the glue to dry completely. To fill the joints, a waterproof grout is used, which is matched to the color of the tile, and, if desired, to highlight the seams, a contrast grout is used.

The joints are filled with a rubber trowel. After 15–20 minutes, when the grout has dried, its remnants are removed from the tile with a dry cloth.

You can lay the tiles on drywall with your own hands, since the tile falls on the leveled surface easily, and there are no problems with maintaining the level and plane.

Drywall is actively used for leveling walls and arranging various partitions, which can then be finished with various materials, including tiles. Plasterboard sheets are attached to the metal frame with self-tapping screws, the caps of which are recessed inside the canvas, and the resulting holes are sealed with putty and covered with nitro enamel or alcohol varnish. This avoids corrosion of the fasteners. The seams between the sheets of drywall are glued with a special tape-serpyanka and are also coated with putty. When laying tiles on drywall, you can use tile glue and mastic as a binding solution. Although experts recommend giving preference to elastic tile adhesive, which has better adhesion to the drywall base.

This video clearly shows the process of performing most of the construction work:

What kind of drywall can the tiles be laid on?

Manufacturers produce several types of drywall, which differ from each other in sheet thickness, as well as resistance to moisture and open fire. It is easy for buyers to distinguish different types of drywall from each other, since manufacturers, along with the abbreviation of names (GVL, GKLV, etc.), use color coding.

In bathrooms and toilets, the rooms in which tiles are most often used for finishing, with the help of drywall they not only level the walls, but also erect various decorative cabinets, niches and boxes from it that cover engineering communications and elements of plumbing equipment. For example, a rigid metal frame of a wall-hung toilet is hidden behind a plasterboard wall, which is finished with tiles and merges with the general interior of the room. Therefore, for people who do not see the power of the hidden frame, hanging toilet bowls raise concerns about the safety of their operation.

What is the reliability of laying tiles on drywall? Experiment: is it easy to remove tiles from drywall

Is it worth laying tiles on drywall at all? From this experiment, you will learn what the reliability is ...

How to glue tiles on drywall?

The main problem when tiling drywall walls is the possibility of warping. To prevent this surface defect, tilers use special guide strips, maintaining a distance of 40 cm between them. Depending on the thickness of the drywall sheet, this distance can be reduced. In addition to the strips, for the same purposes, you can also use a plaster polypropylene mesh, which is glued to drywall with PVA glue or fixed with staples.

Also, the installation of two layers of drywall allows you to increase the strength of the base. Let the consumption of material increase, but the strength of such a wall will no longer cause concern.

Important! Drywall must be treated with a primer, which is applied to the surface of the building material in two layers. At the same time, in accordance with the technology, each layer of the primer is given a drying time, which ranges from 40 minutes to an hour.

Elastic moisture resistant tile adhesive is diluted in accordance with the instructions immediately before laying the tiles. For uniform mixing, use a drill and a special nozzle. Applying the tile according to the previously made markings using a level, the master slightly presses on it, and the glue mixture is distributed over the entire seamy surface of the tile.

We will help you choose the layout of the bathroom tiles in a special material: website.html. Layout options and design solutions.

Important! Uneven distribution of the tile adhesive under the cladding, resulting in voids, must not be allowed. The presence of such voids impairs the quality of the adhesion of the tile to the base and may damage the tile in these places as a result of mechanical stress.

When laying tiles, the following work algorithm is followed:

They draw up a tile laying scheme, taking into account the number of solid and cut rows, the placement of the pattern, the way of arrangement of the facing elements, the presence and width of the tile joints.
They beat off the zero level and carry out the markings using a water level, which later allows not to think about the evenness of the masonry.
Apply glue to the wall and start laying the tiles by inserting cross-shaped plastic spacers between adjacent tiles.
The glue is removed from the joints before it has set to facilitate the grouting process later.
After laying out five rows of tiles, it is necessary to take a technological break, which should last at least an hour. This time is enough for the glue to set.
Next, the next four to five rows are laid out and again an hour break.
Grouting is carried out after the tile adhesive has completely dried. In this case, the spacers are removed, and the grout is applied with a thin spatula and the excess that has fallen on the tile is washed off with a damp cloth.

Do you find it difficult to calculate the required number of tiles? .Html.

Important! After laying the decorative border, it is also advised to interrupt the facing work for an hour. This will prevent possible squeezing of tiles from the masonry.

Features of cutting tiles

To cut the tile into pieces of the required size, use a special tool - a tile cutter, which allows you to get an even cut edge. There are various models of this tool, which differ in principle of operation and price. However, even the cheapest models allow you to achieve the desired result, so for household use you don't need to spend money on an expensive professional tool. In addition to the tile cutter, you may need special drill bits to cut round holes in the tiles.

This material will undoubtedly be useful to those who do not know how to glue tiles on drywall. After reading the tips and watching the video, you can get an idea of \u200b\u200bthe complexity of facing work. And nevertheless, it is better to trust the laying of tiles to specialists, otherwise you can spoil the expensive and beautiful material, violating the technology of work.

What kind of glue to glue tiles on drywall

A lot of modern materials wander day after day in different sectors of construction. Among these, drywall sheets can be noted. The material has successfully conquered the construction market, taking pride of place among the finishing materials. In particular, it is used for both indoor and outdoor work, which is its undoubted advantage. And the latest modifications and coating with moisture-resistant compounds, which allows it to be used in humid rooms, allows use in the bathroom and kitchen. Accordingly, it becomes possible to lay tiles on it, hence the question on which glue the tiles on drywall are best placed.

It is to this question that we will try to answer fully. But first you need to figure out what kind of drywall the tiles can be glued to, and whether it can be done at all.

Is it possible to lay tiles on drywall

Let's first figure out which surface you can put tiles on and on which not. And we note that laying on drywall is a rather controversial issue, since it is necessary to glue on paper in fact. But at the same time, the answer is YES. And this is due to a number of factors:

Another questionable point in the search for answers on what surface to lay tiles on when it comes to drywall in the bathroom is laying on decorative elements. In particular, quite often such material is used to create decorative items, for example, a cabinet under the bathroom. And here we note that tiling is possible, and besides, it is the best solution.

Choice of materials

First of all, it becomes important to choose on what surface and with what means to glue the tiles, taking into account the characteristics of the room.

Drywall

To begin with, we note that the material itself is made from a combination of gypsum and cellulose paper. In the end, a unique material is obtained, which is an excellent tool for all kinds of operation in various conditions:

Environmentally friendly, which does not emit harmful substances into the environment
Fireproof.
High strength is noted.
Fairly good thermal insulation properties.
To this it should be added that it is easy to process, which makes it possible to carry out and implement any ideas with ease and little time (compared to other materials).
It is important to note that even a person who does not have special qualifications and work experience can deal with finishing with drywall.

This is a kind of ordinary drywall sheet. For tiles, it is better to use a moisture resistant, greenish color

Speaking about the basis on which the tiles are laid, it is worth first deciding what kind of drywall actually happens. In total, the production of material offers only two types for consideration:

Standard drywall sheets for normal conditions. Particularly for use at a stable temperature with normal humidity levels. Mostly used for decorative walls and ceilings, as well as creating partitions in rooms.
GKLV - moisture resistant drywall. It is intended for use, decoration of rooms with high levels of humidity, for example, a kitchen or bathroom. Moisture resistance is determined by the presence of a hydrophobic impregnation, which, in fact, allows you to lay tiles on it.

Type of moisture resistant plasterboard

There is another type - this is fire-resistant drywall, but in this case it is not necessary to consider it.

Also note that the first option is used for tiling, and besides, it is not recommended for bathroom decoration. That is why it will not work. Accordingly, the only type that can be used is moisture-resistant plasterboard sheets.

And it's time to consider what kind of glue is best for gluing tiles on drywall. To begin with, in total, you need to familiarize yourself with the types of compositions and then decide which one to choose, and only after that go to the store for a new purchase.

In total, the following types of mixtures are presented to our attention in the construction market:

Cement composition. This is the standard tile mix. Consists of cement, sand and additional plasticizers, as well as modifying components.
A good option would be “Liquid nails”, which are based on a water-dispersed substance.

Typically, liquid nails are used for tile repair work.

It is also worth giving a little advice on the glue itself here. It is worth mixing it only in such an amount that you can use in a short period of time, since such glue quickly sets and after the slightest drying it will no longer be possible to use it. In addition, you should only breed according to the instructions.

And we come to the end, and finally, let's decide on what kind of glue you can glue ceramic tiles on drywall. And here it is worth noting several choices:

Let's note a few of the highest quality and most popular types of glue:

Ceresit CM

Excellent and flexible tile composition

Another similar glue mixture - Elastic tile adhesive Moment... Also suitable for all types of tiles, at the same time it is most often used for clay. Possesses a high level of adhesion, is resistant to material slipping, and besides, it is moisture resistant.

Gaining popularity

Next, it is worth noting the glue from the manufacturer of drywall products Knauf Flizin... This material becomes practically the best choice for a small budget, since it has the ideal combination of low cost and good quality. The glue mixture has a low consumption, some elastic characteristics (insignificant, but for use in a residential building with an average intensity of use in rooms with high humidity, it is perfect). In addition, the adhesive mixture is excellent for laying tiles with a high moisture consumption, without the need for pre-soaking. This tile adhesive is recommended by the manufacturer Knauf for gluing tiles to drywall.

Perhaps this is the most proven high-quality tile adhesive for GL in the ratio of price and quality.

Having considered several examples of the highest quality adhesive mixtures, the choice is yours. A more elastic blend such as Ceresit CM 17, but such glue is quite expensive. The cost of adhesives in different regions of Russia starts from 350-700 rubles per package of 25 kg. At the same time, quite high-quality, and the optimal solution would be to use a standard cement mixture with a small proportion of additives, for example, the glue above Knauf, the cost of which is 2-3 times less. Here it all depends on your personal choice and financial capabilities.

When preparing tile adhesive, it is important to follow the instructions and monitor the mortar life. This is the guarantee of quality.

In conclusion, we suggest that you familiarize yourself with several videos that will tell you in more detail about laying tiles on drywall, preparatory work, including the selection of an adhesive mixture in different operating conditions of the coating.

After the grout layer has dried, it is covered with a protective varnish, liquid glass or silicone sealant. This will protect the material from moisture and mold and mildew. After the grout applied to the joints has completely dried, they are treated with a water-repellent varnish. This is important for wet rooms, as it allows you to strengthen the waterproofing of the walls. The wall is ready for finishing. If everything is done correctly, the surface will be flat, solid, capable of withstanding a certain load.

If the wall is painted, water should be avoided. Otherwise, wipe off immediately. Do not use acid and alkali detergents. The use of drywall in construction makes it possible greatly simplify the solution of most problems in the field of repair... This also applies to laying tiles on drywall in the bathroom.

Tiles on such material are placed without additional manipulation, in the form of alignment. Its surface has excellent adhesion, which allows tiles to be firmly and securely attached to it.

No need to align walls, due to the initially flat surface;
Possibility to put an additional layer of insulation under the surface of the drywall;
Easy to obtain material of the correct size and shape, for installation in corners or at joints;
Highly simple tiling process, which can be carried out even by a person who does not have construction experience;
Minimal waste of time to carry out all events.

Waterproofing with tape

Mix the mastic and apply it with a brush or spatula to critical areas - water pipes. You should work very carefully here. If the mastic gets inside the pipe, it should be immediately removed with a rag, napkin.

All surfaces subject to contact with water - walls near sinks, bathtubs and shower rooms, floors and the lower part of the walls should be protected by a waterproofing system applied under the tiles to the drywall in the bathroom. The fact that walls and partitions made of gypsum plasterboard can be successfully painted and pasted over with wallpaper is confirmed by all specialists. But there are some disagreements about the cladding of plasterboard surfaces with tiles.

Moreover, some craftsmen categorically refuse to glue the tiles on the gypsum board, believing that it can quickly fall off. Most often, drywall is used in construction for the construction of light partitions, false walls, equipment of niches for various purposes, when installing arches and other openings of complex shapes. The choice of the type of drywall sheets depends on where exactly these structures are located, and in what conditions they will be used.

How to glue tiles to drywall in the bathroom

Regardless of the width of the profile, it is best to use one made of metal sheets with a width of at least 0.6 mm. The elements of the frame should be at least 40 cm apart from each other, and the sheets should be laid in two layers. Thus, the frame will not bend under the weight of the tile, and the seams between the tiles will not disperse under the influence of negative factors. If the tile laid on drywall cracked during operation, it can be easily replaced.

To do this, cut out an area with damaged tiles so that you get a small hole. After that, take a new profile, fix it on the wall with hangers, cut out a suitable piece of drywall, close the hole and stick a new tile on this place. Step 3. Apply the glue to a small area of \u200b\u200bthe surface using a notched trowel 2 mm thick (the layer of the mixture is not more than 5 mm), press the tiles well onto it.

Too liquid glue will drain from the wall, and too thick mixture is unevenly distributed over the surface. The optimum consistency of the mixture should resemble thick sour cream. Preparation of the drywall surface for laying the tiles consists in applying a putty and a primer.

You will not be able to do without these stages, otherwise the tile will come off under the influence of negative factors.

Plasterboard tiles in the bathroom: installation technology

After completing the preparation, you should wait at least a day for all materials to dry and set. After that, you can proceed to the main part of the work. Moisture resistance. Sheets with such properties can be installed in rooms where there is a humid microclimate. Such plates are used in the repair of the attic, kitchen, bathroom and toilet; Use good epoxy grout (Litochrome, Atlas). They are quite expensive, for that they serve for a long time and exclude moisture from entering the sub-tile space, which affects the finish catastrophically.

Epoxy compounds are not afraid of household chemicals and aggressive environments.

First of all, we beat off the line of the beginning of the second row with a laser level. The maximum distance from this line to the floor should not exceed the tile size plus the gap. Along this line, we fix the SD profile along the perimeter of the walls;

Then we measure the height, subtract 3 mm and divide by the height of the slab plus 3 mm. We round up. We multiply the number of tiles obtained for each row by the number of rows, and we get the required amount of material.

Drywall in the bathroom

With the correct arrangement and subsequent finishing, the walls in the plasterboard bathroom will last for more than a dozen years. However, this is ensured not only by strict adherence to the technology of repair work, but also by the relatively high technical and operational properties of the GKLV itself. The main advantage of this method is the absence of the need to create a metal frame, which reduces not only the labor intensity of the work, but also the final cost of finishing.

Also, moisture-resistant drywall is recommended to be used for finishing window slopes, which are also exposed to high humidity. The main advantage of this method is the absence of the need to create a metal frame, which reduces not only the labor intensity of the work, but also the final cost of finishing. GKLV ceiling is produced with a thickness of 9.5 mm. As the name implies, it is intended for rough finishing of ceilings, the device of decorative multi-level ceiling structures.

Smaller thickness minimizes floor and fastener loads and thus reduces material costs.

Drywall is one of the most popular materials for wall cladding in any room. It has a number of advantages, including low cost and ease of use. True, choosing a solution for decorative finishing of gypsum plasterboards is not an easy task, because the material consists of pressed gypsum and crushed waste paper, which are "afraid" of moisture. This is especially true when it comes to finishing a bathroom - for this, tiles are often chosen, which have their own characteristics in installation. Below you can read about how to glue tiles to drywall in the bathroom and what to consider when doing the work.

Modern manufacturers offer several types of gypsum plasterboards that are used to level the walls in rooms:

For laying tiles, it is best to take sheets of gypsum plasterboard, which are resistant to moisture and do not deform when interacting with water. The use of conventional drywall (gypsum plasterboard) can lead to the fact that the finish will eventually become unusable. Sometimes gypsum plasterboard is used as a basis for tiles, but before starting work, you should make sure that the ventilation in the room is absolutely correct and works as it should.

Important: the moisture-resistant material can also be distinguished by its appearance - the manufacturers mark it in green.

How to choose a tile adhesive?

The second important point that must be considered when laying tiles on a drywall base is the choice of an adhesive mixture. From the entire assortment presented in stores, it is recommended to use cement-based mixtures, elastic glue, and liquid nails.

Composition	Benefits	disadvantages
The composition includes sand, cement, as well as plasticizers and other additives. Suitable for laying tiles on small, flat surfaces	Versatility (suitable for almost all types of tiles), high environmental friendliness, reasonable cost	Under certain conditions (in particular at low temperatures) it quickly hardens
One- or two-component mixtures with plasticizers	High elasticity, due to which the finish is not afraid of temperature extremes, strength, good adhesion	Relatively high cost
Based on water emulsion	Resistance to moisture and other negative factors (fungus, mold, etc.), ease of use	Fast drying, high cost, some formulations are toxic

Adhesive mixtures for laying tiles on drywall are produced by the following companies:

Ceresit (Ceresit CM11 glue is especially popular);
"Vetonit";
KNAUF;
Knauf tile adhesive "Flizen"
"Plitonite";
"Kreps";
"Atlas".

ceresite tile adhesive

How to choose a tile for drywall?

Any type of tile is suitable for laying on drywall, but a number of features should be taken into account that may affect the final result.

Appearance. The surface of the tile that is laid on the plasterboard surface should not have chips, as well as smeared or fuzzy ornaments, stains or abstract ornaments. The best option is plain tiles or tiles with clear patterns.
Evenness of tiles... It is recommended to glue tiles with an absolutely flat surface on drywall - you can check the evenness by folding the tiles with the front side, and assessing their tightness, as well as the width of the gaps. The corners of the products must be absolutely even.
Material hardness... So that the tile does not deform when the temperature drops, you need to choose solid specimens. It is impossible to check this characteristic visually, but you can lightly hit the surface of the tile - a high-quality material will have a dull sound.
The size... The best option for drywall is a standard size tile with a side length of no more than 33 cm. In this case, the load on the slabs will be evenly distributed, and the elements will hold as securely as possible.

It is better to buy tiles with a margin, and the number of tiles should be about 15-20% higher than required.

Important: both plastic and ceramic tiles are suitable for laying on drywall, but it is important to take into account that plastic products will cost less, but will last much longer.

Step-by-step instructions for tiling drywall tiles

Facing drywall with tiles is a fairly simple, but laborious process that requires compliance with a number of conditions.

Stage one. Installation of plasterboard sheets

As mentioned above, first of all, you should sheathe the walls of the bathroom with plasterboard sheets. This is done in the usual way, but there is one important nuance that should be taken into account: there will be a considerable load on the surface, so the frame must be strong enough - it should be reinforced with horizontal elements (racks). This is especially important in cases with spacious rooms - tiles can deform or even come off from constant vibration. There are several types of profiles that are used to strengthen the drywall frame:

universal standard (50 mm);
reinforced profile (75 mm);
the most durable profile (100 mm).

Regardless of the width of the profile, it is best to use one made of metal sheets with a width of at least 0.6 mm. The frame elements should lag behind each other by at least 40 cm, and the sheets should be laid in two layers. Thus, the frame will not bend under the weight of the tile, and the seams between the tiles will not disperse under the influence of negative factors.

Important: if it is impossible to sheathe the walls with plasterboard in two layers (in small rooms, this method of sheathing "steals" a large amount of usable area), you can do another way. In the intervals between the elements of the profile, the walls should be pasted over with plaster mesh, which is fixed with brackets. After performing such work, the tiles can be laid on the surface without fear that as a result it will deform or come off. Some experts use both a metal profile and a reinforcing mesh to strengthen the frame.

Stage two. Preparation of tools and materials

To lay tiles on a plasterboard surface, you will need the following tools:

building level;
spatulas;
brush or paint roller;
tile cutter;
Tile cutter with "ballerina"
a drill with a nozzle for mixing the glue mixture;
special crosses for aligning seams;
fine sandpaper.

As additional materials for the work, a primer and putty will be required. A cement-based putty or polymer mixtures are best suited for working with drywall. Cement putties are cheaper, but they have one drawback - they give a little shrinkage after drying. Polymer-based compositions are distinguished by their high cost, but at the same time they have excellent performance characteristics: high moisture resistance, strength and no shrinkage.

Primer is another important material that cannot be dispensed with when laying ceramic tiles on drywall. The optimal solution for bathrooms is water-repellent compounds that will protect the cladding from moisture. Some of them contain antiseptics that prevent mold and mildew from growing on the walls. It is also important to pay attention to the fact that the primer does not contain toxic substances - for internal work it is recommended to choose acrylic mixtures that are absolutely safe for human health. Almost all other compounds (for example, alkyd or phenolic) contain toxic substances, therefore they are used exclusively for outdoor work.

Important: when choosing a primer and putty, you need to pay attention to the fact that they are compatible with each other, so it is better to dwell on the products of one company.

Stage three. Surface preparation

Preparing the drywall surface for tile laying consists in applying a putty and a primer. You will not be able to do without these stages, otherwise the tile will come off under the influence of negative factors.

Step 1... Remove the chamfer. It is good to clean the surface from dust.

Step 2... Thoroughly process all joints with putty, so that the result is a monolithic structure.

Leveling the layer with a spatula, example

Step 3. Apply reinforcing tape to the treated seams, on top of which also apply a layer of putty.

Step 4. Wait for the mixture to dry and sand the seams with fine sandpaper.

Step 5. Apply the last layer, wait until dry and sand it again with sandpaper.

Step 6. After complete drying, the putties proceed to the application of the primer. It is applied with a brush, a paint roller in two layers, and each of them should be allowed to dry (at least 45 minutes).

After the primer has dried, the walls should be a flat, solid surface on which the tiles are laid.

Important: all technological holes for communications must be treated along the contour with silicone sealant in order to avoid the accumulation of moisture in these places.

Video - How to putty drywall

Stage four. Preliminary markup

Drawing up a tile laying scheme and marking is necessary to ensure that the appearance of the cladding is aesthetic, and the amount of scrap and waste is minimal. To mark the horizontal rows of tiles, you must define the zero level. To do this, a point is put in one of the corners, which is transferred to other corners, and the distance and evenness of the line must be controlled by the level. A markup is drawn along the resulting line, which will serve as a guide for the horizontal rows. It is better to mark vertical rows from above - in this case, the tile that needs to be cut will be at the bottom and will not be so noticeable.

To determine which part of the wall is best to start with, measure the length of the surface and divide it by the width of one tile. If the number obtained in the remainder is more than ½ the width of the tile, it is recommended to start the cladding from the part of the surface that is most visible - this will make the cut off part the least noticeable. In the case when the remainder is smaller, then it is better to lay the tiles from the center of the wall so that the cut elements at both ends of the row are the same, and the laying looks symmetrical.

After all measurements, a line should be marked on which the bottom row of whole tiles will be located. After preparing the surface, it will be necessary to fix a wooden strip along it, which will serve as a support for the tile until the glue mixture hardens (otherwise the tiles of the lower row may slide under the weight of the upper ones).

Stage five. Laying tiles

Laying tiles on drywall practically does not differ from laying tiles on other surfaces - the most important thing in this case is accuracy and careful observance of all conditions. Particular care should be taken when cutting elements - in order to separate the necessary part of the tile, you should run a tile cutter over it, and then gently hit it on a hard surface. As a result, the tile should split into pieces with even edges.

Step 1. Attach a wooden or metal batten to a batten at the height where the first bottom row of tiles will be laid.

Step 2. If a dry glue mixture will be used for laying the tiles, it must be diluted as indicated in the instructions. It is better not to prepare a large portion of glue, as the mixture “grasps” rather quickly, and after a while it will become unusable: it is better to focus on the amount of glue that is required to lay a square meter of tiles.

Important: in order to get a good end result, you need to choose the right consistency of the adhesive mixture. Too liquid glue will drain from the wall, and too thick mixture is unevenly distributed over the surface. The optimal consistency of the mixture should resemble thick sour cream.

Step 3. Apply glue to a small area of \u200b\u200bthe surface using a notched trowel 2 mm thick (mixture layer - no more than 5 mm), press the tiles well against it.

You can also apply a thin layer of glue to the back of the tile to avoid voids between the cladding and the wall. If the tile is small, it can be glued by hand. For large tiles, it is better to use a wooden or plastic hammer with special attachments.

Step 4. Plastic crosses are inserted between the tiles so that the seams are the same size. Remnants of the glue are removed immediately, before it hardens - this will facilitate the grouting process in the future.

Step 5. In a similar way, lay out 4-5 horizontal rows of tiles, then take a break for about an hour. This is necessary so that the mixture has time to grab, and the weight of the upper rows does not move the entire masonry.

Then the last step should be repeated until the entire surface is faced. The adhesive dries for at least a day, but it is better to start the next stage - grouting - at least three days later.

Video - Laying tiles on drywall

Stage six. Grouting

After the glue has completely hardened, you need to remove the plastic crosses, lightly sand the seams with emery and rub them with a special mixture. The grout is matched to the color of the tile or, conversely, by contrast, so that the surface has an original look.

The grouting mixture is applied with a rubber spatula, and after 20-30 minutes, when it is well absorbed into the seams, its remnants should be washed off the surface. It should be noted that grout performs not only a decorative function, but also protects the seams from moisture and dirt accumulation.

Leveling grout with a rubber trowel

Cladding repair

If tiles laid on drywall cracked during use, they can be easily replaced. To do this, cut out an area with damaged tiles so that you get a small hole. After that, take a new profile, fix it on the wall with hangers, cut out a suitable piece of drywall, close the hole and stick a new tile on this place.

How to avoid mistakes when laying tiles on drywall?

In order for a plasterboard surface to be tiled with tiles to be reliable and durable, you should avoid a number of mistakes that beginners often make.

Insufficient reinforcement of the frame. If you ignore the stage of reinforcing the drywall sheets with a metal profile or reinforcing mesh, the tile will quickly collapse and crumble.
When mixing glue, it is important to observe the proportions indicated on the package.
Incorrect application of the solution to the surface. It is necessary to apply glue on the surface in such a way that there are no voids left between the wall and the tile, otherwise the tiles may crack in these places (this is especially true in cases where the floor surface is tiled with tiles). In addition, it is necessary to ensure that the mortar layer is as even as possible, otherwise the cladding will be wavy, and those tiles that are above the surface will come off in the future.
Any mechanical impact on the tile before the glue is completely dry is prohibited. It is better not to touch the lined surface, and even more so not to start walking on it before the mixture is completely set. At first, imperceptible destruction will appear on it, but in the future they will intensify, and as a result, the decoration will have to be redone.
Poor work of seams. Poor seam treatment with emery and inaccurate grouting leads not only to a deterioration in the appearance of the surface, but also to the fact that dirt and moisture will begin to accumulate between the tiles.

Facing with tiles or plastic tiles is the best option for any bathroom with plasterboard walls. Subject to all the rules and stages, the finish will delight the eye for a long time and will not require special care or constant repair.

Constantly check the evenness of the tiles with a level so that the finish is of high quality