A visit to the Russian bath has become a family tradition for many. Many owners of private houses want to install a bath building on their personal plot, but often they are faced with the problem of arranging heating. There are several ways how you can heat a modern steam room and other rooms located in the bath.
The choice of the type of heating structure depends on the financial capabilities and wishes of the owners. Since the steam room is used from time to time, therefore, before heating the bath, it is necessary to decide how this building will be used.
If it is planned not only to take a steam bath, but also to wash and take a bath, then using a regular oven for heating will not be very convenient.
Modern methods for providing heating in the bath all year round are varied, among them the most popular are:
- electric floors;
- installation of water heating;
- installation of a "warm floor" system and others.
Using the stove-heater
When the room is small in area and it is used only for its intended purpose, then the heating of the bath in winter and at other times of the year can be provided by an ordinary heater. Usually, in this case, a ready-made unit is purchased, having previously determined its capacity. In this case, you can use the stove for a bath and heating at the same time, which is very convenient.
The stove shown in the photo mainly runs on wood - a traditional and inexpensive form of fuel. There are other heating options, among which, for example, the use of electricity, gas, diesel fuel, etc.
Electric heating
When deciding how to make heating in a bath, it must be borne in mind that the cleanest option for creating a heating system is the use of electricity. The use of modern equipment makes it possible to provide heat supply to the building in an autonomous mode in the required thermal mode.
In order for the electric heating of the bath to work, you need to install a boiler that operates on electricity. In this case, there is no need to equip ventilation and build a chimney (read also: ""). This option will be the best solution if an uninterrupted power supply is ensured in the region. Otherwise, you should stop at another heating method.
Modern electrical units are distinguished by a high degree of safety, their complete set includes:
- expansion tank;
- coolant pressure sensors;
- filters for water purification;
- valves.
Gas heating of a bath
The advantage of gas heating:
- environmental Safety;
- use of equipment that is easy to operate and maintain;
- cheap way of heating.
Gas boilers for heating a bath, even in winter, in case of prolonged non-use, are able to heat the room to the desired temperature for several hours, depending on the area of the room.
The function of a gas oven is similar to that of an electrical structure. The gas is burned in a special chamber located under the stones. As a result, not only they are heated, but also the room and the water in the container are warmed up.
Water heating structure
Installation of water heating is considered to be a convenient and quite effective way of providing heat to the bathhouse. With this heating method, firewood, gas, electricity can be used as fuel, since this depends on the modification of the fuel boiler that will be installed.
The best choice of a heating unit would be a cast iron boiler for a heat transfer fluid. Water is heated in it, through pipes it enters the radiators installed in the sauna building, and after the heat is released, it returns to the boiler. The water system allows you to evenly and efficiently heat any room. In the same way, you can organize the heating of the bath from home.
Underfloor heating system
This option for heating a bath belongs to modern methods, which have been used often in recent years. It is rather difficult to install special equipment without relevant experience.
It is much easier to install an electric floor system and you can do this work yourself:
- First of all, a waterproofing material is laid, on which a layer of solution is placed.
- This is followed by the arrangement of thermal insulation.
- An electric cable is mounted on top of the thermal protection layer and the screed is re-poured.
The technology for creating a floor with water heating is similar, but in this case, not a cable is used, but pipes are laid to circulate a hot coolant.
Heating from the central heating main
When the household is connected to the heating main, then it is possible to connect a bath building to it. This method of heat supply is the most efficient and economical.
Before heating the sauna from home, you will need to lay an additional circuit in this room. Best of all, a professional with special equipment and relevant knowledge will cope with such work. Before connecting to a centralized heating main, it is necessary to develop project documentation and obtain a permit, which is issued by the relevant authorities.
Self-arrangement of a warm floor
The base of the floor is preliminarily prepared, then the screed is poured using cement mortar. Next, the rough base is waterproofed using a special mastic. Then a thin layer of mortar is laid and carefully leveled.
When the mixture is completely dry, the heat-insulating material is mounted. Take a heating cable or mat and spread it over the floor surface, connect it to the power supply and test the functioning of the system.
In the event that the structure works, a thin layer of mortar is placed on top of the cable. After it dries, they proceed to the finishing of the floor surface.
- To ensure optimal and efficient heating of the room, the heating of the bath from the stove in the steam room is done as follows: the firebox is placed in the dressing room, the heater is in the steam room, and the tank with warm water is in the washing compartment.
- A non-combustible material is placed between the stove and the wall, and when using firewood as fuel, a metal sheet of the required size is placed in front of the door.
- When a steel stove is purchased, then the room will warm up quickly, but to maintain the required temperature, you need to constantly put firewood in the firebox, since it does not store thermal energy well.
- Stone stoves, despite the fact that they warm up for a long time, remain hot for a long time and gradually release heat into the room. Such a heating structure made of bricks should be laid out by a master. If a metal stove heats up a room in about 2 hours, then a stone one - in 5 hours.
- When a residential building has a small area and is located near a bathhouse, then a bath stove can be used to heat a house, for example, a summer cottage.
The choice of fuel often depends on the individual wishes of the owner of the building. Some of them prefer firewood, because there is a pleasant aroma during their combustion in the steam room, but one must not forget that the heating of the stove with their help is a laborious process. It may be easier to install an electric or gas heating unit.
Warm floors in the bath are a good option for those who use it all year round, who have it at home, and to whom it serves not only for its intended purpose, but also at the same time is the only bathroom in the house, especially during cold weather. It is then that warm floors will make your stay even more pleasant in the bath, especially if you decide to place them also under the main room. Then the warm floors of the steam room will be an excellent additional source of heating.
Benefits of underfloor heating for a bath:
- The heating system is inside the floor
- Even distribution of heat over the entire area of the room
- At low cost - the possibility of heating a large area
- Significant savings over electrical
Warm floors in the bath convenient to use, non-toxic and cheap in cost, but with all this, it is necessary to have additional heating sources in the room, such as radiators, since underfloor heating cannot provide absolute heating of the entire room, especially when severe frosts come.
What do warm floors look like?? Between the concrete base and the coating itself, there is a system of pipes through which water or other heating fluid flows. And in order for all the heat to go up, they are immediately put on, thus ensuring good heating of the bath.
Now we will consider several very important points that you should consider when choosing a stove used to heat a bath. It is advisable to decide in advance what kind of fuel the bath will be heated with, it is good if it will be inexpensive, in recent years are increasingly used. What are the ovens for the bath:
- Permanent action... During the entire use of the steam room, the combustion of the fuel must be constantly maintained.
- Periodic action... It is enough to heat them in advance.
Read also: Features of bath brick stoves
Regardless of the size of the bath, always should be warm enough, and this function is most often performed by the oven, it is she who heats air throughout the room... First, it is worth deciding on the material for the furnace, and only then carefully read the installation technology and the rules for the operation of the sauna stove.
Continuous oven
The main distinguishing feature of the oven permanent action- This is a relatively small layer of masonry and a small amount of stones used for masonry. With an oven like this, you have the ability to regulate the temperature, which can reach 360 degrees... To heat such a stove, you only need to ensure its connection to the mains. But you can also use gas as fuel.
Batch oven
The main feature of the oven periodic action- this is a thick layer of masonry and a large number of bricks that you will need to lay it out. The large wall thickness will protect the furnace surface from possible overheating and, due to its high heat capacity, will ensure the supply of heat for a long time.
This type of heating will allow you to bring the temperature of the lower part of the oven. up to 1000 degrees... Even when reaching such a high temperature, there is no soot settling, as it will all burn out.
The Most Suitable Fuel You Can Use in a bath of this type Is firewood. The use of coal for heating is discouraged. Do not try to drastically lower the oven temperature, as this is dangerous and can cause destruction of the oven's inner surface due to sudden changes.
Material selection
Think in advance about all the materials that you will use during construction, they should in no case be flammable. Also arrange for the necessary room ventilation... There are many materials recommended for the device of the furnace, but the most popular are brick and steel.
Read also: Stoves for a Russian bath with a closed heater
To heat the entire bath, one stove of the heater is enough for you. Therefore, it can be made small to save space. Usually, brick ovens are used for heating, although there are some that are adapted to constant combustion.
The main advantage of the heater stove is that long after heating it will give off heat due to its high heat capacity, despite the fact that the heating time is minimal, it will be able to keep the temperature high in room. To install such a stove, you will need the services of an experienced stove-maker, and this will be quite expensive.
For the most part, metal ovens work on the principle of continuous action... This material is very thin, and therefore cools down rather quickly. That is why the combustion process is constantly maintained in such furnaces, but it will also warm up much faster than a stone one, all for the same reason. For small baths with a light foundation, this is perfect option.
Fuel
The next very important point that you should pay attention to - this is fuel... For heating a bath, you can use not only firewood, as many think. Of course, burning wood guarantees unique aroma of wood and the special warmth of the bath, but making a supply of firewood for the whole winter is not an easy task. Modern technology can provide us with more convenient energy sources.
Today there are stone ovens, electricity, the same wood, and, of course, liquid fuel. There are also models that combine the use of several types of fuel at once. You can of course make a similar oven and do it yourself, but this will require special skills and the necessary experience.
In the case of using electric heating for a bath, you can adjust the current strength in the heating elements yourself. It is also very important not to forget during installation about the installation of an automatic protection system, which will stop the further supply of electricity if the temperature in the oven rises above the permissible norm.
When choosing a fuel, you should pay attention to the price and availability, in that firewood is significantly inferior to, because they are very difficult to get, electricity is available to everyone, but it will come out more expensive. Liquid fuels are not only flammable, but they will also cost you a lot. Gas is cheap, easy to use, but not always available.
The key to a good sauna is a properly folded stove. This is perhaps the most important attribute of the bath. It is this kind of heating in the bath that will allow you to heat the room, heat the bathing water and create steam in the steam room. To heat a large sauna, you can install a heating stove. If you do not know how to make heating in a bath, but have decided to build a steam room, the best option would be a heater stove.
Peculiarities
In summer cottages, family-type baths are built for themselves, in which one heater is enough. This type of heating in a bath will take over all the basic functions. It is with this that the fact that it is important to observe all the subtleties during the construction of the furnace is connected. It is better to make a small stove-heater. This will save space. At the same time, the time of its heating will be minimal, and it will give off heat as long as possible. But the most important thing is what kind of fuel it will be heated with. It is best to keep the fuel cheap. Popular - water heating of a bath.
Steam room - the main room of the bath
The high heat capacity will allow you to get good steam for a long time. In addition, dry heat will be used to heat the room and water for washing. So that everything suits you when making heating in a bath with your own hands, take into account the ratio of the size of the stove, the room and the purpose of the bath. Make sure that your stay in the bath is as safe as possible for you and your family.
Think over to the smallest detail what materials you will use in the construction of a bathhouse and stove so that they are not flammable. Responsibly approach the issue of ventilation. Whether it is gas heating in a bath or electric - this will allow you not to burn out from combustion products.
The principle of operation of the oven
Let's talk a little about how the heating system of the bath will give off heat to the outside. If the heat radiation is at its maximum, you risk overheating or getting burned. Also, excess heat negatively affects the condition of the skin. In order for the conditions of stay in the bath to be comfortable, the stove must give off heat according to the principle of convection. Hot air comes from the oven, and cooled air is supplied.
To achieve this result, the temperature of the oven walls will be lower. But fold the walls of the bath from materials that will reflect infrared rays as much as possible. Heat accumulates well in the wall and in the stone backfill. In order for the stove to give off heat as long as possible, build its walls thicker.
Furnace types
Stoves-heaters, which are used by heating a bath in winter, can be divided according to the type of work into two categories: continuous and intermittent.
The continuous kiln is characterized by a small wall thickness and a small volume of stones. This type of stove has the ability to regulate the temperature both independently and automatically. In this case, the maximum temperature value reaches 350 degrees. To heat a stove of this type, it is enough to connect it to electricity. Gas is also suitable as fuel.
If you decide to use electric heating in the bath, you can adjust the current in the heating elements yourself. Do not forget that when installing the oven, you are obliged to install a protective automatic system. If the temperature of the walls exceeds the permissible values, the heating of the bath with electricity will independently stop the supply of electricity.
Also, continuous heaters can be heated with coal or wood. Whatever you heat the stove-heaters, whether it is water heating in a bath, remember, it is important to separate the combustion chamber and smoke channels from the backfill.
To do this, you can use steel sheet or lay cast iron tiles. Thus, you will prevent the penetration of combustion products into the sauna room. It is also an excellent stone protection against soot deposits. The latter, in excess, pollutes the air in the bath.
Stoves-heaters of periodic work are represented by thick masonry and a large volume of bricks. Thick walls will protect the stove surfaces from overheating, and the stove will give off heat for a long time.
Such heating in the bath allows you to heat the lower part of the stove to 1100 degrees. Working at such a high temperature, there is no soot settling as it burns out. In order to save fuel, they use the "black" combustion principle. In this case, the smoke gases pass through the bath. This heating option is very dangerous. The surface of the stove and walls is covered with soot. As for the “white” version of the firebox, the firebox compartment is covered with a flap. It is allowed to open it after complete combustion of the fuel.
The most ideal fuel for making heating in a bath can be wood. It is not advisable to use coal for heating. It is quite difficult to drastically reduce the temperature, which leads to destruction of the internal surfaces in the furnace. And this already violates safety regulations.
To get an economical use of the fuel, it is important that it burns completely.
The shutter is closed during combustion, special attention is paid to the air supply. When it enters, water vapor and carbon dioxide are formed. If there is no air supply, soot build-up will form, resulting in low heat output. The risk of poisoning by combustion products increases. It is also possible to increase the heat transfer coefficient by heating a larger surface. It is necessary to heat the stove until the walls are heated to the maximum temperature and dry steam begins to emit.
What kind of stoves are there? Here are some of their designs. There are solid fuel stoves that are fired with coal and wood. Liquid fuel, for them kerosene or fuel oil is suitable as fuel. There are models of gaseous fuel stoves. For their work, you need to have liquefied or natural gas - heating the bath with gas. As well as electric ovens.
Heating in the bath is a private matter for everyone. But in order for bathing procedures to be a joy in winter, it should be comfortable inside the room. Thanks to heating in the bathhouse in winter, you can quickly heat up the rooms, while using the minimum amount of firewood, run water supply and have a hot shower with an equipped bathroom.
Heating a bath in winter
The classic sauna heater is a metal or brick heater. Additional equipment is required to maintain the air temperature in the steam room and in other rooms.
Some people prefer hot water heating. With this type of heating, water floors or radiators are connected to the heating system of the house or to a heating plant.
Many people prioritize electric heating because of its ease of use. You can always quickly heat a small room with a few electrical appliances.
Heating with a stove
If the bath is small, then the heater is the best option. It will easily heat the room without additional heat sources and costs. Its popularity is due to a number of advantages:
- ease of installation and maintenance;
- ease of operation;
- fuel availability.
There are also disadvantages:
- high fire hazard;
- emission of combustion products;
- there is no way to automate the heating of the room;
- large weight and dimensions of the oven.
Today, heaters run on a variety of fuels. These are firewood, gas, electricity, liquid fuel. The choice depends on the material wealth and technical capabilities of the equipment itself.
Heating by furnaces with heat exchangers
Such heating heats the room, provides it with hot water and generates steam. Heat exchangers are used in steam rooms, washing rooms, rest rooms, shower rooms, swimming pools, dressing rooms.
When designing a bath in this way of heating, the following are taken into account:
- the size and area of the room;
- stove features;
- the weight of the heating equipment;
- coolant volume;
- chimney length and diameter.
Heating can be connected to an expansion tank, to radiators, to hot water supply.
Many ovens with a heat exchanger are filled with antifreeze or water. The principle of operation is based on the natural circulation of liquid due to temperature differences. Some are equipped with an electric pump.
A warning! The heat exchanger must not be heated if the tank is not filled with water. In winter, drain the water from the system.
Electric heating system
This type of heating requires special attention to the electrical network of the room, since there will be a large load due to thermal electrical appliances. The wiring must be in perfect order.
It is necessary to take into account the wiring diagram, wire cross-section and the total load on the power grid.
With this type of heating, you can use an electric boiler, an electric stove, an electric convector, an infrared film. Infrared heaters are fully used.
Modern electric boilers are equipped with automation that maintains the temperature in the bath.
This heating can be used throughout the year.
Gas heating system
Gas-heated baths are fast, efficient and economical. There are no unpleasant odors, no soot and soot. Gas equipment is compact, lightweight and does not take up much space. There is no need to think about heating water, it is heated with gas.
Advantages of a gas-heated bath:
- Cheap and environmentally friendly fuel.
- Simple maintenance and use of the device.
- Safety in use.
Important! When using a gas heating system, safety rules must be observed. The bathhouse must be equipped with an automatic device that stops the gas supply in an emergency.
Water heating system
A water heating system is a practical, convenient and affordable way to heat a sauna in winter.
It heats the room quickly and evenly and automatically maintains the temperature. Water acts as a heat carrier. Fuel can be electricity, gas, solid or liquid fuels. Heating equipment - a boiler or stove.
Heating system with warm floors
As an additional source of heat, it has become very fashionable to carry warm floors in baths. They are made in a relaxation room, steam room or washroom.
The heating medium can be heated with wood. In this case, the power consumption will be approximately 45 watts for the two circulation pumps.
It is not difficult to make such floors. The main thing is to choose the right pipe diameter, calculate the pump power and the resistance of the circuits.
It is imperative that two circuits be drawn separately: to the relaxation room and to the steam room with a washing room. We need to put taps to regulate the temperature.
To increase the speed of water circulation in the system, you need to connect the hot water tank to the boiler with copper pipes 22 mm in diameter.
Advantages of a water-heated floor:
- the heating system is located inside the floor;
- not only small but also large areas are evenly heated;
- energy saving.
Warm floors can be water or electric.
Heating system from the heating main
Today, modern technologies allow heating from home to the bathhouse. This takes time and money. It is necessary to agree with the relevant authorities.
With such work, it is necessary to take into account the passage of groundwater so that the pipes do not end up in the water. The pipeline must be insulated without fail. Put on a corrugation or a pipe of a larger diameter from above.
The closer the objects are to each other, the cheaper it will cost to heat the bath in winter.
Alternative and mixed heating options
Such methods of heating a room are popular and practical. The best solution for mixed heating is when the bath is used infrequently. You can make heating in the sauna from the stove and carry out electric heating.
Advice! If the bathhouse is not constantly operated in winter, then it is imperative to drain the water from the boiler, water heater, pipes, toilet tank (if any). This will save you from unnecessary problems.
Alternative sources of heating can be conditionally divided into main and additional groups. The main ones completely heat the entire room. And the additional ones support the work of the main heat source.
A diesel boiler can be considered an alternative heating option. It must be installed in a separate room because of the specific smell of fuel. It is also important to think about where the diesel fuel is stored.
Pyrolysis heating boilers can be used. In them, the fuel burns out for a long time and almost completely. But the disadvantage of such a boiler is the high cost and complexity of operation.
If the stove is brick, then the heating of the bath from the bath stove can be carried out in the steam room. This option is effective if the bath is rarely used and is small in area.
Alternative heating options can be heat pumps, electric convectors, solar collectors, water heating.
All systems can be divided into two types of heating:
- forced circulation equipment;
- equipment with natural circulation.
With forced circulation, the coolant moves thanks to the pump. It maintains the required temperature and pressure in the system. It needs electricity to work.
Natural circulation includes the boiler, batteries, expansion tank and pipes. We need a competent routing of pipes, the correct calculation of their slope. The disadvantage is that the expansion tank must be at its highest point.
How to make heating in a bath
Heating in the bath is necessary to ensure amenities.
One of the types of heating is automatic. Separate heating can be provided by electric convectors or electric boilers, as well as gas boilers. All of them can work offline. It can be adjusted so that there is a slight positive temperature in the room. This will allow you not to drain the water from the toilet bowl, pipes, electric boiler.
There is a minus in this system. Since it is autonomous, you may not notice that a failure has occurred and the temperature may drop below zero. Therefore, it is necessary to install a temperature sensor with a signal.
How to heat the sauna from home
You can install both gas or electric boilers, as well as stone or metal stoves. But these are all rather complex constructions.
To heat the bathhouse from home, you can lay a heating main there. Install radiators in the house. Such a system will operate on heating in the house.
Heating a bath from a bath stove
The easiest heating method to manufacture, operate and maintain is heating a bath from a bath stove. The stove is installed directly in the steam room, and the firebox is in the dressing room.
Brick ovens keep the temperature for a very long time, but they need to be warmed up for at least 5 hours. And it takes even more time to heat a bath in winter.
High cost is another drawback. It is very difficult to fold such a stove on your own. The help of an experienced stove-maker is needed.
Heating the dressing room from the sauna stove
In most cases, a classic bath is heated by a single heat source. The stove is installed in a steam room so that all rooms can be heated. The water tank is placed near the washing room.
It is very important that every furnace element is made of refractory material. Therefore, it must be built from bricks. Such an oven will take up a lot of space and be large.
The ideal option would be a stove with a tank and an open heater. The firebox is equipped with a register, the lower edge of which is located 50 cm above the register. It will prevent premature boiling of water.
Is it possible to make heating from the tank
To install a heating system from a tank, you need to know its specifics of operation and operating rules. It is necessary to take into account the volume of the room and the power consumption.
There are wall-mounted and built-in tanks. There are also manual tanks - a container of water is placed on top of a heated stove.
Comment! You can use the already created heat: a tank is hung on the chimney, the water heats up, and the temperature there can reach 500 degrees.
These methods do not supply hot water to the shower. This can be done by remote water tanks. The heat exchanger is placed in the oven, a tank is hung next to it or in the attic. The system is connected by pipes through which water will flow. Thanks to the heat exchanger, it heats up and flows through the tank into the shower. Such a heating system is simple and efficient.
Hinged tanks are sealed containers with a lid and a tap for draining water. Attached to the wall with metal hooks. Made of stainless steel.
Attached water tank - an inclined pipe welded at the end is welded into the furnace. The other end is at the bottom of the tank. Cold water rises up an inclined pipe, where it is heated to a boil. Hot air bubbles transfer heat.
How to make heating in a log sauna
Three types of heating are installed in wooden houses: water, electric and air. Each has pros and cons.
The most popular type of log house heating is water heating.
- Profitability.
- High heat capacity.
- Difficulty in installation.
- The need to constantly monitor the heat generator.
- In winter, be sure to drain the heating system.
Such heating systems are:
- with bottom or top wiring;
- passing or dead-end;
- one-pipe or two-pipe;
- vertical and horizontal;
- with a pump or natural movement of water.
Two-pipe systems are less aesthetic than single-pipe systems.
Electric heating has several advantages:
- The level of heat supply is easily adjusted.
- Small dimensions of heating devices.
- Heating is environmentally friendly and quiet.
Air heating has only one plus - high penetrating power.
But there are much more disadvantages:
- large stoves and fireplaces;
- very low heat dissipation;
- uneven distribution of air in the room;
- expensive heating systems.
Before installing systems, it is necessary to weigh the advantages and disadvantages and possibly consult with an expert from the industry.
Conclusion
Heating in a bath is the most important thing that needs to be paid attention to during construction. The bathhouse is one of the best recreation places where you can spend time with your family or friends. If it is warm and cozy there, then the rest will be soul and body.
If you equip a bathhouse in your courtyard and decide how to make heating in the bathhouse, you must remember that the stove can perform several functions. It is intended not only for generating steam in the steam room and heating water, but also for heating all rooms. If this is not enough, then other heating options can be provided.
Heating types
The main types of heating are:
- oven;
- electric;
- gas;
- liquid fuel;
- mixed.
In areas where people live permanently, they often carry out heating from home to the bath in such a way that it is warm all the time, does not freeze in cold weather. This is very convenient if gas is supplied to the house.
When choosing one or another heating model, you must proceed from its availability for you and the cost of the fuel that is used in each option.
The main points can be noted:
- heating with wood is quite troublesome, but it is in keeping with tradition. The crackling of firewood in the stove creates a wonderful mood for a person, adjusts to rest;
- the use of electricity for heating a bath is very convenient, you can heat the floors, you can heat the water, you can think of a lot of things, but all this is quite expensive;
- the use of liquid fuel stoves, for example, with diesel fuel, is very dangerous and is not recommended for the private sector;
- natural gas is an ideal solution to the problem, but not always possible, since it is not supplied everywhere, and the use of the balloon version is not always effective.
Gas
Gas systems are economical, efficient and create a comfortable, permanent environment in the room. There is no need to think about hot water for washing, as it is also heated with gas.
For the device of gas heating in a bath, separately or in conjunction with house heating, a competent project is required. The initial costs for the design and installation of the system will be offset by the ease of use.
When using such a system, you must follow the safety rules. Instructions for using the equipment should always be at hand. And it is advisable to study it thoroughly.
Important. The bath, which is heated with gas, must be necessarily equipped with an automatic device that stops the gas supply if the flame suddenly goes out.
Stove
The most common option for generating heat is. From the sauna stove, while it is heated, all the rooms of the sauna are also heated.
The wood-burning stove for the sauna and the heating of the changing rooms are classics of the sauna tradition. If the bathhouse is located far outside the city, and there are no other sources of heating in it, then firewood is the most versatile and affordable fuel.
Wood-burning stoves provide uniform heating of the air, as well as quick heating of the required amount of water. They are very compact, which makes it possible to use them in a small space in the steam room.
In the video presented in this article, you will find additional information on this topic.