All are familiar with the screwdriver. This is a manual power tool designed to twist and spinning a variety of fasteners. This is the main direction of its application, but not the only one. With the help of a screwdriver, you can create a great many useful and necessary things.
Screwdriver as a generator
Screwdriver can be used as a generator. Make it very simple. You need to remove the battery, connect the wires on the terminals using crocodiles and connect them to the consumer. Be sure to predetermine the multimeter to check the polarity. In the cartridge you need to insert and clamp the hex key for the furniture assembly. Through the spindle rotation will be produced current, which will receive the consumer. True, it is worth noting that the voltages of the produced by this electric machine is enough except for charging a mobile phone or a small LED lamp.
Using wind energy using a screwdriver
Under this principle, wind generators from the screwdriver are built, but the current produced is so small that the game is not worth the candle. Its installation is more effective in the districts of a large wind load, although it does not justify the result there.
Equipment for carpentry workshop
Some more interesting offers, how to make equipment for home joinery based on a conventional screwdriver.
Turning machine
In the manufacture of products from wood it is difficult to do without a lathe. It can be built with your own hands. A smooth wooden workbench is perfect for the bed. A screwdriver can be used as anterior grandmother and drive rotation. In a wooden bed made of a bar in the form of a screwdriver, you need to put the tool and fix the clamp. The bar can be fixed with a clamp, and with constant use of the machine to fasten with self-draws. In the cartridge you need to insert a dental mandrel. The rear grandmother is performed from two bars with an adjusting screw that is sharpened under the cone. It is installed opposite the fixed screwdriver so that the axis of the tool coincides with the axis of the rear grandmother's adjusting screw. The design of the rear stop is fixed by the clamp. If you plan to handle large parts, the mount should be more reliable. The girlfriend can also be made from the bar, securing it to the workbench of the clamp. Primitive lathe for a home workshop is ready.
Desktop drilling machine
Another equally important equipment is a drilling. It can also be made of screwdriver. This will require a used screwdriver. It is necessary to take the engine with the gearbox and the cartridge. Now you need to make two clamps from the textolite, which will perform the function of fixing the drilling head of the machine. To achieve the maximum coaxiality of all holes on the clamps, it is better to process together, for one set. Then it will be possible to avoid distortion.
As restrictive racks use sleeves with internal threads. They must be the same size corresponding to the distance between the clamps. After that, another clamp of the textolite and two bits from Caprolon are made. They are not drilled in the center, receiving two eccentric bushings. The clamp is installed on the rod and with the help of eccentrics choose the backlash. After that, the lever from the tree on the spring is installed so that the drilling head is returned to its original position. To power, you must use a transformer with a power of more than 150 watts and output voltage, like a screwdriver used. After that, you need to put the diode bridge and the condenser, install the drilling head on the bed.
Manual Mill from the screwdriver: Step by step instructions
It can be converted into a manual milling mill. For this you do not need to acquire expensive materials. Everything you need is found in the workshop or garage almost under your feet. For the arranging of the manual milling from the screwdriver, the slices of thick plywood or chipboard will be needed, clamp for fastening the tool, fasteners in the form of bolts and screws, a plumbing tool and a feather drill for wood. In the latter case, you can use the drilling crown.
Collect the homemade milling mill is quite easy. For this you need: 
- From pieces of selected material, cut the base, a vertical rack, on which the screwdriver, emphasis and shelter will be enshrined to give stiffness of the structure using the clamp. The dimensions of the parts are selected arbitrarily, in the ratio to the dimensions of the power tool.
- Based using the feathery drill to drill a hole Ø 40 mm for free access of the cutting tool into the processing zone.
- Make a clamp on the diameter of the hand tool.
- At the vertical rack with the help of a clamp, fasten the screwdriver so that its cartridge is at a distance of several millimeters from the base.
- Install the ribbiness.
- At the vertical rack, fix the screwdriver by the focus.
- In the cartridge tool to install a milling mill.
Mill from the screwdriver is ready to use. Such a machine will not be able to become a full-fledged replacement for manual milling due to low power and low spindle speed, but will solve the issue of milling small parts in a home workshop.
Circular Saw
In addition, for its carpentry workshop from the screwdriver you can make a circular. To do this, make a working surface, applying a DSP sheet or a thick phanener. In the countertop you need to perform propyl to the outlet of the disk saw. The screwdriver must be securely secured from the bottomside of the working surface, using metal or wooden clamps. In the same way, the shaft is fixed. It is important that the saw blade goes over the working surface of the table is no more than a third of its diameter.
Modernization of children's vehicles
And of course, all the best to children. On the basis of a screwdriver, it is possible to modernize many children's vehicles. For example, a children's pedal machine to remake in an electric vehicle.
Electric vehicle
For the manufacture of a car with an electric drive, you will need:
- Frame made of steel profile pipe. It can be made with your own hands.
- Wheels can be applied from a garden trolley on a rubber move.
- Body can be taken from the old pedal car or come up with some creative solution. For example, soldering out plastic pipes.
- As an electric drive, it is necessary to use two engines from the screwdrivers and gearbox from the same power tool. Separate enclosures are made for them, in which the output shaft is set to 201 bearing.
- Battery. You can use the usual car 6st60.
After all components are cooked, it remains to collect an electric vehicle. This process is simple and under the power of every man who even has a superficial view of the plot.
Electrosocat and electric bike
Another use of a screwdriver in the creation of vehicles can be called electrical sink or electric bicycle. The principle of such modernization is based on the installation of a chain transmission between the wheel of the wheel and an electromotor asterisk with a screwdriver gearbox. Power of this device is carried out from the battery of the hand tool. This solution does not require high costs. As a result of improvements, a vehicle is obtained at a speed of movement from 5 to 15 km / h.
Electric snowmobile
With the help of a screwdriver, not only vehicles on wheels can be made, but also the real snowmobile. It is necessary to use an electric vehicle for this by conducting a number of relevant upgrades. It is necessary to improve the electric vehicle frame to install the drive wheel on it. Instead of driven wheels, you need to install skis, the plastic harness of the car is replaced with a metal bicycle wheel. The drive of the drive wheel is carried out through the chain transmission from the screwdriver.
Assembly such a miracle technology will not take much time, and most importantly, funds. All costs will pay off the joy of the child, for which the electric drive vehicle will become a real gift.
Cool ideas and weights of the use of a screwdriver in the household
In addition to the listed mechanisms, the screwdriver can be applied to the embodiment of other ideas in the economy. This manual power tool will help automate the opening of the entrance gate, make a winch for a car or scissors for cutting metal. If you attach the nozzle for cutting the tin, you can turn the usual rubber boat into the engine, to upgrade the process of drilling the wells when treated fishing. In addition, everyone knows that the screwdriver is used as a drive to the mixer, meat grinder or juicer.
After reviewing the article, the reader received knowledge of the unconventional use of the screwdriver. Now he can apply this hand tool to create a carpentry workshop equipment, improving children's vehicles and other useful things in home everyday.
To create homemade bormers, I used the 775 size engine, which I ordered from the Chinese.
Such engines can be found in the screwdrivers and, it seems, in compressors for pumping tires cars. Not in every screwdriver stands such an impressive engine. The engine has a diameter of 5 mm. It took another nozzle-cartridge, which you can buy.
By the way, a very convenient cartridge, clamping up to 4 mm, does not hit at all. You can clamp any hooks for engraver or drill. It is desirable to have an engine speed regulator such
The total budget of this device turned out about 1,100 rubles (without a power supply for a computer). The power supply can be used by any 12 V (depending on the engine voltage), but its power must be comparable to the power supply of PC. This engine consumes 1,5-2a at idle. Under load current increases. The power supply for 250-350W will cope without problems. Even when the emergency shutdown nozzle is encircled.
The revolve controller from this engine is very weak, because the load is inconstant. Adjustment is very useful when working with plexiglass and melting plastic. And with the case, you can polish or polish the heels.
The engine has a ball bearing in the front, behind the sleeve. In general, the motor inspires confidence, very heavy and good. Surplus of power and reliability does not happen.
Let's see what we did in the end.
The enclosure for the engine is made of segment of the sewer tube, from the ends, dried by plexiglass. Cutouts in the enclosure for ventilation. There are no special holes in front, only the gap between the shaft and the housing (4-5 mm). I was afraid to make ventilation in front, because the engine will pump dust and dare. Almost everything is assembled on a thermocher from a pistol (compacing). Heating is no strong and the strength is sufficient. To keep the thermocons better, you need to preheat the bonded surfaces. I use soldering hairdryer for this. Glue black Stayer.
The homemade is largely superior to the finished Chinese bormer (engraver). I can compare because I have this. The homemade is heated less, with comparable power. Minus homemade in the insufficient speed of rotation, 10-15 thousand / minutes for some nozzles are not enough. But this question can be solved by purchasing the engine with a greater speed of rotation. On Aliexpress the choice of sufficient.
In general, the device satisfies me completely. Of course, it is not a Bulgarian and metal cutting it problematic, even thin. It takes not so fast, but copes. Engine heating is, but not critical. There is some inconvenience when engraving, keep inconvenient. When used, you need to remember that the engine shaft, albeit thick, you can break it or bend it. Therefore, do not forget that you have a tool for thin work in your hands. With plastic, wood and other not very solid materials copes wonderful. Therefore, it is possible to recommend radio amateurs in the manufacture of enclosures for crafts, cutting circuit boards. You can cut, drill, clean, expand holes of various shapes, milling.
Good luck!
Hello!
Some small and delicate projects are impossible to boron cars, but not everyone can buy it for amateur affairs.
In this article, I will tell you how to make a born-shock on a screwdriver from the girlfriend and I will be pleased if my idea is useful to you.
Materials and tools:
2 bearing from rapid coils
- valve from the chamber of the cargo car
- screws for nuts on 10
- Cap nut on 10
- Bike brake cable
- Plastic hot water pipe for 20
- Screwdriver
- Handsman for metal
- Filty
- soldering iron
And so, let's start with the most complex mechanism of this device, namely from the tip.
For him, we will need two bearing from the random coils. Similar bearings I saw on sale bearings in a radio store of details. I did not buy them, since I had in stock broken coils.
And as a shaft for bearings, I used the brass valve from the chamber of the cargo car wheel.
Cut off excess
clear the future shaft in the cartridge of the screwdriver and rotating it, the nappill melts the necks for bearings.
After that, you need to make a crimp mechanism for nozzles or collet. To do this, I decided to drill the screw suitable for the nut on 10. Fixing the screw itself in the cartridge of the screwdriver, and installing the 2.5 mm drill in the other, or in the vice rotating screw drills it along the axis.
Cut off the screw cap and gently, in the center we make four axial slots in a depth of 4-5 mm, thereby dividing the end of the part into four parts. If you allow the slightest displacement making a slot or a hole, then the clamping cams are different, in the future the nozzles will vibrate and the use of such a bormer will be difficult.
By setting the workpiece by the shank in the cartridge of the screwdriver, the proper is screwed up the head under the cone.
Then we deploy the workpiece by fixing 12 mM rod with a conical part in the cartridge of the screwdriver, stepping the thread of the shank, thereby reducing the diameter of the part to 5 mm. And on the very shaft, we increase the inner diameter of the drill of 5 mm, deepening it about 2 centimeters.
We insert the item into the shaft and drill a 2.5 mm drill, a pin with a nail with a nail diameter binding them between themselves.
For the second part of the crimping mechanism, I decided to use a steel cap or a deaf nut on 10. I could not find such a nut and I had to unscrew it from the door handle from the metal-profile.
That in the nut exactly to make a hole in the center, I drilled another screw and wrapping the screw tightly in the nut, the same drill drilled the hole in it.
Then, measuring the end of the crimping mechanism, the 4 mm drill increased the hole in the nut and the drill of 5 mm from the inside removed the chamfer.
As a flexible Sleeve Bor Machine, I used the brake cable of the bicycle. Rounding in a shirt, the cable will transfer the kinetic energy of the screwdriver on the tip.
By the way, the nut from the brake system is not suitable for the head of the collet. Cap walls are too thin for this.
Now you need to connect the cable with the shaft. For this purpose, I drilled another screw, only this time, a smaller diameter and long.
Measuring the thickness of the cable, the drill is 1.5 mm drill the screw and cutting off the hat with reducing the rod diameter in the same way.
Then we depress the cable into the rod about half of its depth. For soldering, I used soldering acid and tin solder. Heat the rod of the burner or on the gas stove and spend the cable.
We note the point of drilling and make holes on the shaft, and then in the rod installing it into the shaft. After, pin, bonding parts with each other.
For the housing, the reinforced plastic pipe was perfect for 20. The length of the pipe is the distance from one to the second edge of the bearing
After removing the chamfer from the plastic tube we will press the rear bearing. And then skipping the cable through it and installing the shaft into it. We will compare and the front until the backlash is disappeared between the shaft and bearings.
Now you need to fix the cable shirt to the tip body. To do this, cut a plastic tube with a length of 2 centimeters and make a core from a wooden bar for it. Having made a wooden blank with a diameter slightly more than the inner diameter of the tube and a length of about 1.5 centimeters, we will press it into the tube.
In the center of the core drills a hole slightly smaller cable shirt diameter and fix it in it.
After laying both parts of the case, we note the place under their mounts. By 1.5, drilling drills, approximately 5mm, and from a suitable nail diameter, we make the mounting pin with a length of about 1 cm.
By inserting the pin into one of the holes, connect both parts, mark on the reverse side of the case and we are doing the same operation for the second fastening.
Greased bearings and cable finally fasten both parts of the case.
The screwdriver from the network is the dream of many home masters. In principle, it happens that the home workshop does not have the need for a battery tool. You can have access to the outlet at any time. Of course, having a battery screw in your hands is convenient. But when working, you hold in your hands, except the tool itself, also the battery. And it will be harder.
Also, batteries are often fighting, breaking. And since on sale you are unlikely to buy the battery separately from the screwdriver, then you have to break your head over how you can provide your screwdriver with the necessary power from the outlet, bypassing the battery devices.
Advantages of rechargeable screwdrivers
Rechargeable screws are very convenient at the construction site - they are very simple to work on the roof, in difficult conditions where the reputable wires will only interfere and create an excessive danger. But precisely there most often and battery breakdown occurs - the screwdriver fell, the battery crashed, and you will have to look for a new one.
Let's figure out how to make a screwdriver from the network.
Replacing the screwdriver with a regular drill
The easiest option is to use a regular small drill as a screwdriver. Just take the bat, and pushing it into the cartridge instead of drill. Working with a drill as a screwdriver will require some skill the fact that the drill does not have a "ratchet" - the scrupted ratchet will work as a fuse when the fastener is tightened. Therefore, you need to clearly feel this moment and let go of the button. Otherwise, torn screws of the screws, damaged bits and mood you are guaranteed. Another difference drove from the screwdriver is the speed of rotation.
If the torque of the torque is small, and the speed of rotation is high, then the screwdriver - on the contrary. Some even have the ability to adjust the speed of rotation. Without a high torque, tighten the big tapping screw is unlikely to succeed - you have to resort to the help of dumping. Therefore, the drill is usually twisted with a small self-sized self-sized.
It is not recommended to use the perforator as a screwdriver, although its operating parameters of torque and rotation and more acceptable. The perforator has a large radial beating, it is difficult to twist the screws with it.
Just a network screwdriver
The second option is to purchase a network screwdriver in the store. They are several types. The first, the cheapest is the same electric drill on which a crack is installed. They are not positioned as a professional tool, and with their help you can only spin the small fasteners. However, the presence of a rattling will save the screws of the screws, your bits and nerves.
More expensive screwdriver - specialized network. This tool has a built-in gearbox, most often planetary type.
They are positioned as a professional tool, and are much more expensive.
Often such screwdrivers have the ability to twist the large nuts, bolts, and a store for small screws. This option is the best, albeit the most expensive.
Alteration of rechargeable screwdriver in the network with their own hands
The third option is to re-equip the battery screwdriver to work from the network. You will need knowledge of electronics and circuitry, so it is not for everyone. In addition, you will need to know the operating parameters of your battery.
If the battery is divided, then you can ask people on homemade forums to measure the current parameters and battery voltage. This will help you make a power supply source. In principle, if you have good knowledge of electronics, you can simply disassemble the battery. Its designs will be chemical batteries connected in a certain way. Knowing their type, from the battery name, as well as a connection scheme, you can quickly estimate the battery parameters. And then collect rectifier with the necessary work parameters. Or even replace the elements in the battery failed. And then collect rectifier does not have to.
Video on the repair and alteration of batteries
This is a repair: This is about the battery type alteration:
This is about the alteration on the network model:
hochu-stroitsya.ru.
How to make a grinder with your own hands from a drill, screwdriver, chainsaws
Sometimes, when performing repair or construction work, a situation arises when equipment fails, and it is not possible to buy new or repaired. In this case, the master needs to know how from existing tools with low costs to make the necessary tool. In this article we will look at what you can make a grinder with your own hands.
Bulgarian from drill
In case of failure of the corner car (ESM or Bulgarian), it can be made of a drill. It should be borne in mind that there are several ways to transform one tool to another. The least costly and not so time-consuming will be the use of a special adapter adapter.
The adapter is an adapter that is made in the form of a rod. On the one hand, it can be clamped into the cartridge drill, and the cutting disk is fixed to the second side with the puil.
If there is no possibility to buy an adapter, you can disassemble the faulty ush and dismantle the spindle.
You can also buy it in the repair workshop or pull the adapter on the machine at the familiar turner. Climbing the adapter in the cartridge drill, we get a workable corner machine.
The disadvantages of the structure include the fact that such a "grinder" can be used only with strict safety compliance. She can cut the metal is not thicker than 5 mm. In addition, since the drill frequency of the shaft rotation is significantly less than that of the ESM (3,000 against 11,000 revolutions per minute), the effectiveness of metal processing in this case is much lower.
The advantages of such modernization include:
- fast conversion of one device to another;
- use the tool in places inaccessible to the ISM factory manufacture.
When using a drill as a cutting device, it is necessary to keep in mind that the tree drill has rotation in both directions. Therefore, when cutting metal or other works, it is necessary to follow the direction of rotation. The cutting disk should rotate only clockwise.
There are another way to alteration. But he is more costly, for its implementation, they acquire a special nozzle, which has a gearbox. The drill is dismantled by a native gearbox, and the nozzle is installed in its place. As a result, it turns out good Bulgarian from a drill - almost a complete analogue of a defective tool.
However, the cost of such a nozzle is quite high, and modernization takes a lot of time. Therefore, it is better to immediately buy an inexpensive ushm.
All presented options are intended only for an emergency solution to the problem. If you need to subsequently use a destination drill, you will have to spend much time on its recovery.
Alteration of chainsaws in a corner
Sometimes it becomes necessary to cut off the pipe or professionalist in a place where there is no electricity. For this, the Bulgarian from chainsaws is used, which is easily converted using the purchased console.
It consists of:
- leading pulley or drum;
- protective casing;
- belt transmission and set of keys and spills.
To install this device on chainsaw it is necessary:
- dismantle the tire with a chain;
- freeing the tank from the oil and remove the clutch drum;
- on the drive shaft of the leading sprocket to mount the pulley of the device;
- consolidate the protective device and set the belt transmission;
- put the cutting disc - and the mechanism is ready for work.
The main advantage of the design is that it can be used in places where electricity is missing. When working with such a machine, it is necessary to observe maximum caution, since the benzopyl torque is higher than that of a standard corner. In this case, the risk of destruction of the cutting disk increases.
Modernization of the screwdriver
If there is no drill or chainsaws at hand, and it is necessary to cut the materials, you can make a grinder from the screwdriver. The algorithm for its modernization is almost the same as in the manufacture of the ears of the drill. The main element of the design will be the acquired nozzle - adapter or spindle faulty USM.
The advantages of such power tools include the quick transformation of the mechanism and the possibility of using away from the electrical network. Homemade can be used in cramped conditions, where the standard EMS is not suitable due to large sizes.
The main disadvantages of the homemade device can be called:
- a small battery life (when using a battery screwdriver);
- low speed of rotation of the cutting disk - about 700 revolutions per minute;
- insufficient power of electrical system.
Such a mechanism can only be used as a low-power AVM. With it, you can cut off the metal with a thickness of no more than 1.5 mm or a corner 20 * 20. They can cut the armature with a diameter of less than 8 mm. Use a screwdriver as a full-fledged cutting tool.
Mini Bulgarian from Program
Such an adaptation is suitable for those engaged in modeling - they often have to cut parts from solid materials. Use standard corner devices In this case, it is impossible: it is necessary to cut very small items. For such work it is necessary to make a mini-grinder. It is made from a small electric motor. It can be from a faulty video recorder, printer or children's toys. Power of such a device is carried out from the cell phone charger, the input of a USB, battery or several batteries.
The most difficult thing is the manufacture of the cutting element with your own hands. The disk is made of the finest cutting circle. The diameter is chosen independently, according to the conditions of application.
Sometimes the cutting circle is made from the ordinary traffic jam from drinks.
The manufacture of the device starts from handle processing - enshrine the engine on it. A collet clamp is mounted on the axis. Take the prepared circle, secure it with the washers on the screw M6. It turns out a peculiar nozzle, which fasten the collet clamp.
The tool is ready to work. The mechanism from the motor can be used without a handle if it is required to trim parts inside the model.
How to make a device, you can see in this video:
All wishing to make the device should be aware that homemade Bulgarian does not meet the safety requirements. If there is no sharp necessity, it is better not to risk your health, and sometimes life.
tehnika.expert.
Self-made drill assembly instructions
Compact homemade mini drill can be used to drill printed circuit boards if you suddenly decided to collect any electric appliance with your own hands. In addition, the hand tool can be used for normal domestic purposes, if there is a need to drill a small hole in a wooden board or plastic. Next, we will tell you how to make a mini drill from a motor with your own hands, providing photo instructions and visual video examples!Method number 1 - Second life with old tape recorder
As you understand, the first version of the self-made mini drill will be made of a tape recorder CD forgotten. All you need from the former sale of sales is a motor who will rotate the drill. Since the device is powered from 6 volts, you will additionally have to find the appropriate power supply or the battery. In addition, you need to buy a collet yourself (sold in any radio car market, the price is small) and find the right body for homemade. 
So, in order to independently make a mini drill from a motor at home, you must perform the following steps:
That's all the device assembling the device with their own hands. As you can see, making a microdel from the motor is not at all difficult, even a new board. The only drawback of such a device is the small strength of the thin drill. If you drill holes not at right angles, it will immediately break.
A very important point you should know about - so that the drill spins in the other direction, simply change the wires in some places! Interesting video instructions on how to make a simple drill provided Roman Ursa on his video blog page:
Simple borrower of girlfriend
Method number 2 - coil into move!
Another original way to make a mini drill at home - using the coil from the fishing rod. In this case, the assembly technology is quite simple, but the principle of operation itself will be founded not on the electrical work of the motor, but on mechanical rotation, by type of a small bormer.
For the manufacture of the device with your own hands you will need:
- non-indication coil;
- the cartridge from the old drill either chung;
- thermocles either cold welding;
- kolyshko.
The assembly process is quite simple and consists of only two stages. First of all, you need to dismantle spanking with a fishing line and cut off the remaining axis. 
After that, the cartridge passes on the remaining rod. You can do without a cartridge and set the collet with your own hands. 
When glue freezes, you can check the finished mini bormashin. You can see all the details of the assembly on this video example:
How to make a microdel from the coil?
Method number 3 - an idea with antiperspirant
Well, the last version of the self-made mini drill, which we would like to provide the readers by the electrician itself - using a cassette motor and a container from the antiperspirant. The advantage of this model is that it will be controlled separately with the on / off button and at the same time charge from a conventional power supply. 
So, you first need to prepare the following materials:
- motor from the tape recorder;
- suitable collet with a drill;
- used antiperspirant;
- rCA socket for power supply;
- switch from old carrying.
First of all, you need to make a mini drill according to the instructions provided at the very beginning: to plant the collet on the shaft and secure bolts. Next, the motor body is installed in the antiperspirant. As can be seen in the photo, the sizes perfectly approached the installation of the part. 
After that, in the upper lid, you need to drill a hole for the yield of the collet either the drill itself. At the same time, in the bottom you need to make a hole on the output of the power cord from the motor. With the help of a stationery knife, it is also necessary to cut the window under the circuit breaker, followed by all the elements of the chain. 
The advantage of this version of the self-made mini drill is convenient control, small size and at the same time stylish appearance. We recommend to make this particular option at home, especially from the girlfriend means at home you can find everything!
Overview of various ideas for creating
Examples for inspiration
Above, we provided the 3 most popular options for self-made microdes to drill printed circuit boards. On the forums, we found some more original ideas that may inspire you to make your own unique homemade.
So, to your attention a photo of the ideas of spare parts for creating a mini drill do it yourself at home:
That's all that I wanted to tell you how to make a mini drill from a motor with your own hands. As you can see, there is nothing complicated, and there is a limitless ideas for the assembly. We hope that our photo examples and video instructions were useful for you and interesting. In addition, you can assemble a microdel with your own using the old drive from DVD, a screwdriver, an electric shaver and even a motorcycle from a washing machine!
Similar materials:
samelectrik.ru.
How to make a mill from a drill with your own hands: components, stages of manufacture, video
The relevance of the question of how to make a mill from a drill with your own hands is explained by the fact that you can buy expensive serial models can afford not all homemade masters. Meanwhile, the usefulness of such a device and the need for its use in many situations (the implementation of construction and repair work, the manufacture of all sorts of wood structures, decorative design of products from various materials) is indisputable.
A simple milling of wooden parts can be performed on a homemade drilling rack.
Using a milling machine, equipped with a relevant working tool, one can successfully perform milling products from wood, form the edges of various configurations on them, prepare the seating for door locks and loops, create a groove on wooden parts, as well as solve many other technological tasks.
Accessories and assembly algorithm
Making a milling machine from a drill, which is practically every home master, it is possible, but it should be borne in mind that such a device will not be able to fully replace the serial model. This is explained by the fact that the cartridge of the ordinary hand drill is able to rotate at a speed of 3000 rpm, while the serial milling mill is able to provide the rotation of the tool used at a speed of up to 30,000 rpm. In addition, the household electric drill gearbox is not designed for intensive loads that will quickly lead it into a faulty state.
Vertical Milling Flower
Scheme of the simplest vertical rack for a drill
Meanwhile, the simplest milling mill made of minimal financial costs is able to successfully cope with many technological tasks. To make your milling machine from an electric drill, you must find the following materials and tools:
- several pieces of chipboard or fat plywood;
- clamp, with which the drill will be fixed on the basis of the device;
- bolts, screws and other fasteners;
- feather drill or boring crown with a diameter of 40 mm;
- standard plumbing tools.
Trimming Rosek, Plywood Slices, Metal Corners - All this can be used for the manufacture of a simple milling rack.
The process of assembling the homemade milling mill itself passes through the following algorithm.
- A chipboard or plywood sheets are assembled by the basis of a future milling ager, which includes a horizontal base and a vertical part on which an electric drill will be recorded. The dimensions of sheets of chipboard or plywood, of which such a design will be manufactured, are calculated depending on the dimensions of the electric drill used as the basis of the homemade machine.
- In the horizontal base of the device, the hole is drilled with a diameter of 40 mm, which is necessary in order to provide access to the tool to the processing zone.
- At the vertical stand of the device, the clamp is fastened with a bolt, in which the electric drill is fixed. The drill should be located in such a way that the lower end of its cartridge is a few millimeters from the horizontal base of the mill.
- To make the position of the drill on a vertical rack more stable, in its upper part you can fix a small wooden bar, which will act as a role.
Stand with height adjustment by lever
How to make the milling machine above described construction more convenient and functional? To do this, it can be equipped with the simplest microlift, which will be responsible for moving the electric drill in the vertical direction. For the manufacture of such an elevator, you will need the following consumables and components:
- two metal rods that will act as guide elements;
- playground (carriage) for fixing the electric drills made from chipboard or thick plywood;
- the threaded axis and nut, which will be responsible for moving the electric drill in the vertical direction;
- elements providing fixation of the electric drill in the desired position.
Stand with height adjustment with threaded stud
The principle for which such a homemade milling mill works is quite simple and is as follows.
- When rotating the threaded axis, the carriage with the drill fixed on it moves in the vertical direction.
- After the electric drill and fixed in its cartridge, the tool will be exhibited in the desired position, the carriage is fixed with the help of fastening elements.
Machine from the old electric motor
The homemade milling machine, with which many technological operations are sufficiently performed quite successfully, can be made and without the use of electric drills. In order to make such a device, you will need the following consumables and components:
- drive electric motor, which can be used by an electric motor from the old washing machine and other household appliances;
- a cartridge in which the used cutting tool will be recorded;
- adapter, with which the drive of the drive motor will be connected to the cartridge;
- sheets of chipboard or thick plywood for the manufacture of the base and the vertical guide of the self-made milling mill.
Homemade machine based on the Soviet three-phase engine
Selecting an electric motor for the homemade milling machine, keep in mind that the power of the latter should be in the range of 500-1100 W. The higher the power of the drive electric motor, the milling depth can be performed by the processing of the mill.
A very important requirement in the manufacture of a self-made milling machine is the absence of backlash in contacting elements of the device. If you neglect this requirement, you can encounter the fact that the processing performed using such a mill will not be highly accurate and quality. In addition, the quality and accuracy of processing performed even on a homemade milling machine, the characteristics of the cutting tool used have a serious impact.
The screwdriver is widely used in various fields of activity to work with fasteners of different types: self-draws, screws, bolts with nuts, furniture configmatics, screws and other. Also, with the help of this power tool, the holes are drilled in different materials, for example, in various metals, in lumber, in concrete. In this case, the functionality of the operated model is determined by its power and torque, the presence of a shock function.
From the screwdriver can be made at home a variety of equipment and tool for domestic use. In addition to the power tool itself for alterations, in many cases will require additional details and materials. But homemade devices will still be cheaper than the factory analogues, allowing you to automate and make more efficient manual labor.
The whole range of screwdrivers is divided into network and rechargeable models. Both varieties of products work due to electrical energy, which leads to rotation the electric motor. Only the electromotor itself in network devices is calculated on an alternating voltage of 220 V, and in the battery equipment for a constant different value, for example, 12 V, 14.4 V. These structural features together with technical characteristics are largely determined by which self-timers from the screwdriver will be collected .
Electricity is one of the main types of energy used by humanity. Due to the electricity, household appliances, industrial equipment, machine tools, power tools are functioning. The work is performed with the electric motors of different designs and power, which is powered by variable or permanent current views. For this reason, on the basis of a screwdriver or from its individual parts, the following technical devices can be collected:
- garden chopper grass and branches;
- trimmer (electrocoso);
- matching manual generator;
- engraver (mini drill, dremel, borders);
- wind generator;
- lawn mower;
- bulgarian;
- mini-machines: drilling, grinding, flight, turning, sawing, cut;
- tool for mating fittings;
- drive opening drive;
- methods for children: quad, bike, scooter;
- small ice free, Yamobur, construction or kitchen mixer.
A powerful shock type model can also be converted to a tank for concrete using a special nozzle.
The implementation of each option occupies different times and requires additional (minor) costs, or costs without them.
Assembling a manual hiking electric generator and homemade wind generator
Of the battery models of the tool, it will not be much difficult to make a self-made generator, which will produce electricity when rotating the hand of the attached handle. Such an adaptation is useful in hiking conditions. To make a dynamo machine, it will not be necessary to radically modify the product. Everything you need to create a hiking generator in the design of the device already exists, only minor improvements will be needed.
With the help of the equipment created, you can charge batteries 6 or 12 V.
For alterations fit power tools with an operating voltage from 18V and above. Modification is carried out in the following way:
- disassemble the electrorewater;
- gently falling out e-board;
- put instead of batteries suitable in parameters (dimensions, technical characteristics) diode bridge inside the battery case;
- make a comfortable handle with a handle;
- the end without handle is fixed in the cartridge.
The final design after the manipulations done will be viewed approximately as in the photo below.
The diode bridge is necessary that the electric generator handle can be twisted in any direction. Instead of the handle, you can insert a nozzle with blades. Then it turns out a simple wind generator.
The electric generator operating from the strength of the windAlso manufactured in another way, in the form of a fluger. At the same time with the battery device do this:
- disassemble the screwing and tear;
- get an electric motor, disconnecting its contacts;
- remove the cartridge with the gearbox (rotor part);
- in the cartridge insert the shaft of the electric motor, clamping it;
- to the gear gear of the bolts are attached a round metal plate about 1 mm thick, which will serve as the basis for fixing the blades made, for example, from plastic pipes;
- clamp with a clamp dressing on the shaft between the patron and gear;
- cut out of plywood or fine metal rectangular base;
- with the help of a clamp with a clamp, the engine is fixed to it with a cartridge, drilled under the fastening of the hole in the right places;
- make the casing to protect the wind generator (from precipitation, dust and other unforeseen influences), for example, from under coffee banks;
- insert the base with the engine and the patron inside, fixing the elements with the help of glue, and the cover - sealant;
- make the blades, connecting them to the round plate of the unit;
- pushing vane;
- one of its ends assembled the assembled generator;
- connect wiring to the outputs of the motor;
- check the output voltage using the multimeter, rotating the blade by hand.
Variants of wind generators a lot. Even the entire screwdriver is attached to the support, providing it with a shock with blades.
Alteration of the screwdriver in the Bulgarian
If the angular grinding machine broke either it is generally absent, it can be temporarily replaced with a battery or network electrorepener. In this case, there are various options for reworking. The easiest way is to apply ready-made or homemade nozzles or adapters. An example of an adapter is presented in the photo below. Its end is fixed in the cartridge, and the disk clings to another.
Another option that can be transformed into the Bulgarian drill-screwdriver is the use of special type nozzles, equipped with reducer. When implementing the method, the power tools disassemble, dismantle its gearbox, and the nozzle is installed instead. After the transformation, the instrument turns out the type of similar to the corner-glare machine.
It should be taken into account that such a special nozzle is expensive, and work on modification requires a lot of time.
Homemade nozzles are made of suitable diameter studs, nuts and washers. They are used even with rechargeable electrical journecks.
The efficiency of the homemade is significantly lower than that factory Bulgarians. This is due to the big difference of speeds of rotation of the nozzles: approximately 3000 rpm in the screw robberite against about 11,000 rpm near the corner grinding machine. A minor power value along with a small speed significantly limit the functionality of the device made.
The devices made should be used only in case of emergency situations. because of opportunities reversal On the reworkable tool, it is necessary to monitor the direction of rotation of the disk to not be injured.
Alteration of the screwdriver in the trimmer or lawn mower
To make with their own hands an electrocos, you will need such details and materials:
- a piece of plastic pipe with a length of about 2 m;
- soldering iron with soldering set;
- fasteners: Self-tapping screws, bolts with nuts;
- 45 degrees plastic corner;
- plug on the pipe;
- 12 V motor from the electrorewater and rechargeable battery from it;
- the wire;
- 50 mm adapter for plastic pipes;
- power button;
- bucket plastic;
- clips Contact (crocodiles) - 2 pcs;
- blades from stationery knives.
The work uses a pipe and a corner to it with a diameter of 40 mm.
The rework process is carried out like this:
- evaluing the electric jugger, reach the motor;
- attach it to the plug, noting the seating holes in it;
- attach 2 electric motors;
- soldering output to the motor;
- install an electric motor, encouraging its wiring in the pipe;
- marker marker on the tube location location of the future switch;
- drill hole;
- connect to the wiring switch, they are mounted;
- to the ends of the outgoing wires attach contact clips to be able to quickly connect to the battery;
- from the adapter make a battery holder;
- connected the drive, connect the adapter with the tube;
- make knives from blades;
- with the usual clamp for terminals, the nozzle is connected to the motor shaft;
- a protective cover is made of plastic bucket;
- glue the part to the pipe;
- check the performance of the design.
The created device will make it possible to mow only herbal cover with soft stems.Different options for lawn mowers based on network models of drills-screwdrivers. In the photos below are two homemade.
Initially, they create from metal, plywood or other materials base to which the wheels are then attached, as well as the control knob. Clamps or rack fix the electric jourver. A cutting nozzle is inserted into the cartridge. To protect the legs from the flying grass, the casing is attached to the back of the base. Power makes a button or directly from the network.
To assemble a fairly functional lawn mower, you need to take a drill screwdriver from 0.5 kW power.
The battery or network model of the electrorewater can be turned into an engraver, which is differently called the dremel, bormer, mini-drill, a straightforward machine. For this, quite simple buy in the store nozzle and pull out any bit under it.
The homemade cartridge will allow the use of a variety of snap-in, intended for dremels.
The process of creating an engraver with a flexible shaft demonstrates the following video.
Production of garden chopper
Garden chopper for grass and thin twigs (less than 1 cm thick) can be made on the basis of a network drill-screwdriver.
Create an aggregate so:
- select a suitable container, for example, zinc welding;
- in the center of the bottom, the hole is drilled under the shaft, on which the knife will be fixed or several blades;
- make a wooden or metal frame for installation of a container or put it on the edge of the table;
- for the frame or the bottom of welders attach a screwdriver, which equipped with knives;
- mount the power / shutdown button;
- make the slot in the container from the side - cut the rectangle before the bottom 10 to 20 cm;
- sleeve makes a sleeve for emissions of crushed plants;
- attach it to the container;
- check the efficiency of the unit.
Knives are easiest to make from hacksaws. Installing them need sharpening down. In this case, you can make several variants of blades for different herbs. If you do to a drill-screwdriver nozzle in the form of knives, then the grass can be simply grinding in a bucket or other suitable container.
Machines made of screwdelt
The craftsmen made a lot of different intended machines from the screwdriver. They fully cope with household tasks.
If you need to work professionally, then without more serious equipment can not do.
One of the options of how to redo the drill-screwdriver in drilling machineDemonstrated on the video below.
Method for creating simplest turning machine Shown in the roller below.
Also on the basis of a drill-screwdriver it is possible to collect the easiest milling and grinding machinesWhat is demonstrated in the following rollers.
Other non-standard ways to use tools
Non-standard use of the screwdriver is not limited to the options considered. The video below shows how to use this power tool as drive for quadcicla And for the opening of the doors (gate), for drilling ice, as a mixer. Also, video contains other non-traditional options.
Using the battery case, you can make a good lamp. The entire assembly process lED lamp Demonstrates a video presented below.
How to adapt the screwdriver electric motor to make electric bicycleit is shown in the videos below.
Another bicycle version with the motor contains a roller further.
With the help of a hook inserted into a screwdriver cartridge, you can knit fittings During the construction of different objects. How it is done, demonstrates the next video.
Connecting a tool to a screw of a manual meat grinder, you can automate the process of twisting vegetables and meat.
It should be borne in mind that the homemakes of this kind are often very limited by load. But if it does not work out practical benefits, then entertainment is guaranteed.
This is not limited to the unconventional use of the screwdriver. The folk craftsmen constantly put forward new ideas, at the same time their practical implementation occurs. Other specialists adapt homemade adaptations to their own needs, while obtaining a variety of modifications of self-made equipment. You can also think of something independently by showing technical knowledge and fantasy, giving the will imagination, creativity. The main thing is to remember: starting to make various devices, it is necessary to take into account that the created mechanisms are safe.