10.10.2016

The passport

Door block metal

1. General information about the product.

1.1 Products consist of four main elements: door frame, door leaf, lock and hinges for hanging the leaf on the frame.

1.2 The door leaf is a welded structure made of one (two) steel sheets, stiffeners and anti-removable pins.

1.3 The door frame is made of complex-shaped steel profiles welded together. For subsequent installation on the box, mounting ears or holes for fastening through the door frame are provided.

1.4 The door leaf and the door frame are connected to each other by canopies welded or screwed to them by hinges, which provide free opening of the door.

2. Basic technical data and characteristics.

2.1 The produced doors can be manufactured (depending on the order) with external, right or left opening.

2.2 The reliability of a metal door must be at least 100,000 opening cycles.

The overall dimensions of the metal door on the frame can vary in width from 860 to 980 mm, in height from 1800 to 2050 mm. Overall dimensions established at the enterprise: width 860 mm, 870mm, 880 mm, 960mm, 970mm, 980mm; in height 1800mm, 1900mm, 1950mm, 2050mm.

2.3 The appearance and finish of the door corresponds to the samples.

2.4 Linear dimensions and maximum deviations correspond to the technical requirements of GOST 31173-2003.

3. Delivery set

	Name
	Door leaf complete with frame
	Door handle (with square)
	Cylinder mechanism with a set of keys
	Lever lock key set
	Set of plugs (for anchor bolt holes, 6 pcs.)
	Peephole
	Passport and instruction manual

4. Safety requirements.

4.1 Products must be safe to operate and maintain and withstand operational loads in accordance with applicable building codes. The material used in the manufacture of door blocks meets the existing safety requirements.

4.2 To work on installation and maintenance of doors, technical personnel with the necessary professional training are allowed.

5. Transportation and storage.

5.1 Transportation of packed doors is allowed in any type of land, air and water transport in accordance with the transportation rules for this type of transport. Transportation, as well as loading and unloading must ensure the complete safety of the product.

5.2 Products should be stored vertically or horizontally (the number of doors in a stack should not exceed 10 pieces) on underlays of the same thickness in closed ventilated rooms at temperatures from -40 0 From to +40 0 С and relative humidity 50 +_ 15%

Devices and accessories not installed on products must be packed in containers.

6. Maintenance and operation.

6.1 Maintenance of the door includes preventive inspections and monitoring of its performance. The frequency of door maintenance should be at least once every three months.

6.2 When carrying out preventive examinations, the following operations are performed:

The completeness of the door and the integrity of the main units (door leaf), rubber seals are visually monitored;

The necessary repair and restoration work is carried out, cleaning and lubrication of the mating surfaces (if necessary). It is recommended to lubricate the hinge assembly with a thin layer of grease every 6 months.

7. The order of installation and preparation for operation.

7.1 Doors are delivered assembled.

7.2 Installation of door blocks should be carried out by specialized firms, specially trained teams.

7.3 CHECKING THE DOOR BEFORE INSTALLATION:

Upon acceptance of the door, it is necessary to check the integrity of the packaging

Check the appearance of the product for mechanical damage and compliance of the product with your order (model, size of the door block, color of the coating, type and color of the panel, opening side)

Check the completeness of the fittings and their appearance

Check the functionality of the locks

ATTENTION! Dismantling the old door is allowed only after all stages of the check have been carried out!

7.4 The door is installed in the openings of brick, concrete, reinforced concrete walls with a thickness of 125 mm and more, as well as in the openings of walls and partitions made of other structural materials, the design of the openings in which allows the installation of doors. For high-quality installation, we recommend using masking tape (to protect the surfaces of the walls and door frame from foam). In addition, we recommend using PSUL (pre-compressed self-expanding sealing tape) for installation in the gap where the metal casing is adjacent to the wall.

7.5 Mechanical damage to the door covering or decorative trim and overlay elements during door leaf installation does not constitute a reason for a claim against the manufacturer.

8. Warranty obligations.

8.1 The warranty period is 1 year from the date of shipment to the customer.

8.2 The warranty period for locks and fittings is 1 year from the date of shipment to the customer.

8.3 The service life of the product is 1 year.

8.4 Warranty repairs are not subject to:

- Products with mechanical damage due to inappropriate conditions of transportation, storage, installation and operation;

Products with signs of self-repair, including self-disassembly of locking devices;

Products with signs of violations of operating conditions;

Products installed in violation of the installation instructions;

9.Certificate of acceptance.

9.1 The metal door block meets the requirements of GOST 31173-2003, is recognized as suitable for operation.

9.2 The manufacturer reserves the right to make changes to the door design in order to improve performance without being reflected in this operating manual and prior notice..

The catalog of interior doors from the Krasnodrevshchik factory contains a collection of classic and modern solutions for interior decoration, including the novelties of 2018.

You can download the catalog in electronic form (.pdf).

Warranty passport on the door Cabinetry

The passport for the door block contains information on the rules for operating the doors of the Krasnoderevshchik factory.

You can download the passport in electronic form (.pdf).

Model line 700 door catalog

A booklet about a new collection of interior doors 2017 from the Krasnoderevshchik factory invites you to familiarize yourself with the 700 model line. Description of the advantages and features of the 700 model line, photos of new door models, types of finishes and other useful information.

Door catalog Cabinetry 2017

The catalog of interior doors 2017 invites you to familiarize yourself with the list of products manufactured by the Krasnoderevshchik company. General information about the factory, a description of the advantages, a range of interior doors in 2016, ready-made solutions and a lot of useful information.

You can download the catalog in electronic form (.pdf).

Door catalog Cabinetry 2016

Door catalog 2016 offers to familiarize yourself with the list of products manufactured by the Krasnoderevshchik company. General information about the factory, a description of the advantages, a range of interior doors in 2016, ready-made solutions and a lot of useful information.

You can download the catalog in electronic form (.pdf).

Door catalog Cabinetry 2015

Door catalog for 2015.

You can download the catalog in electronic form (.pdf).

Special doors catalog

Special doors - fireproof, soundproof, vandal-proof, moisture-proof, chemical-resistant and others.

You can download the catalog of special doors in electronic form (.pdf).

You can download the price sheet electronically (.pdf).

The price list shows the prices for the products of the Krasnoderevshchik company for all model lines, including the prices for door moldings.

You can download the price sheet electronically (.pdf).

The 2013 catalog presents a new collection of interior doors from our factory, ready-made solutions for design and construction organizations, as well as a special offer for DIY retail chains.

Your attention is provided with detailed information on each model line, the unique advantages of our products.

You can download the catalog in electronic form (.pdf, 11.5 MB).

Interior catalog

The catalog contains brief information about the factory, contains photographs of all manufactured door models, and gives a brief description of their advantages. In addition, the catalog contains some of the manufacturer's recommendations for door installation.

You can order a catalog (free of charge), indicating in the letter information about yourself, your postal details.

The catalog is sent by mail, or received directly at the FSSI "Krasnoderevshchik" CJSC at the address: Russian Federation, Chelyabinsk, st. Mechanical, 40. Order catalog

You can also download the catalog in electronic form (.pdf, 2.8 MB).

Directory

You can get acquainted with the products of the factory, including the latest innovations, in the new Buyer's Guide, where information is presented in the form of illustrations and a brief description of the characteristics of door models. Ask for a guide at all points of sale where our products are presented.

These technical conditions apply to wooden interior door blocks (hereinafter referred to as doors), manufactured by LLC"XXX", Cheboksary.

Doors intended for residential and public buildings.

These specifications apply to the following types of doors (according to GOST 6629):

- ДГ - deaf doors;

- DO - glazed doors.

An example of recording products in other documents and (or) when ordering:

"Interior wooden door DG TU 5361-001-XXXXX-2012"

The list of reference and normative documentation of these specifications is presented in Appendix A.

1. TECHNICAL REQUIREMENTS

1. General requirements

Doors must comply with the requirements of GOST 475, the requirements of these technical conditions and be made according to the working drawings of the manufacturer.

1. Main parameters and characteristics
2. The appearance and color of the doors must correspond to the reference standards approved by the head of the manufacturer.
3. The nominal dimensions of the doors must comply with the standards given in table 1.

Table 1

Block designation	Door size (height x width), mm	Door block size (height x width), mm
20-65	1900x550	1971x620
20-7	1900x600	1971x670
21-7	2000 x 600	2071 x 670
21-8	2000 x 700	2071 x 770
21-9	2000 x 800	2071 x 880
21-10	2000 x 900	2071 x 970

1. Limit deviations from nominal dimensions in curvature should not exceed± 4 mm.
2. Doors, their assembly units and parts must have the correct geometric shape.

The deviation of the door leaves from flatness should not exceed

2 mm in height, width and diagonal.

The deviation from the perpendicularity of the sides of the door leaves should not exceed 2 mm per 1 m.

In the corner spike joints of boxes, the height of the sag should not exceed 0.5 mm, and in the corner joints of the linings of the canvas - 0.3 m. The gaps in the shoulders of the spike joints of the boxes should not exceed 1 mm.

Sags along the ends of the spike joints in the canvases are not allowed, and in the boxes there should be no more than maximum deviations from the nominal length of the parts.

1. The frame should be made of spliced ​​pine beams, on which MDF sheets with a thickness of 6 mm are glued on both sides.
2. Doors should be lined with PVC films with a thickness

(0.3 - 0.4) mm.

1. The moisture content of the wood of the door parts should be 8± 1%.
2. Door parts must be connected in accordance with the requirements of GOST 9330.
3. The door frame, faced with MDF on both sides, is pressed in a hot double-sided press for 20 minutes.

After processing and applying the appropriate patterns, the canvas is covered with a PVC film and cured in a vacuum membrane press.

Assembly of the door leaf can also be done dry on dowels with fastening at four corners with tightening screws.

1. Glue is used for door claddingHomakol 133 according to TU 2252-007-59759080-04.
2. The roughness of the front surfaces of doors for an opaque finishing coating should not be more than 200 microns, for a transparent finishing coating - no more than 60 microns (in accordance with the requirements of GOST 7016).

Fringes and burrs in tool slots should be cleaned off.

1. On the front surfaces of doors with decorative cladding with sheet or film materials, the size and number of scratches, dents, stains, as well as uneven gloss and dullness should correspond III class according to GOST 24404. Mechanical damage to the door surface (scratches, dents, abrasions) - unacceptable. Foreign inclusions under the facing material are unacceptable. Irregularities are unacceptable.
2. The types, sizes, finishes and workmanship of devices and fasteners used for doors must meet the requirements of the standards for these products and parts and indicateXia in the customer's specification.
3. Devices, cover strips, layouts and other parts must be fixed with screws, pins and nails in accordance with the requirements of standards for devices and this standard.

The screws must be screwed in. Driving of screws and the exit of the ends of fasteners to the door surface is not allowed.

1. Glazing should be made using silicone and special inserts.

Glass used for glazing doors must comply with GOST 111, GOST 5533 and GOST 7481.

1. Glass surfaces must be clean, no dirt, oil stains, glass chipping, chips, glass edge protrusions, damage to glass corners are allowed.
2. Requirements for materials and purchased products
3. Materials and products purchased for the manufacture of doors must comply with the requirements of GOST 475 and current regulatory documents.
4. Materials purchased for the manufacture of doors, including materials of foreign production, must have a certificate of conformity or other document confirming quality.

Polymer and synthetic materials used for the manufacture of doors must have a sanitary and epidemiological conclusion and fire safety certificates.

1. The basis of the door leaf is a frame made of spliced ​​pine beams (moisture content 8± 1%), on which, by hot pressing using industrial glue (Homakol 133 according to TU 2252-007-59759080-04), MDF sheets are glued on both sides (fibreboards for construction and household needs according to TU 5536-009-44779728-2003) 6mm thick.
2. The door leaf is covered with PVC film (GOST 24944) 0.3-0.4 mm thick. The ends of the canvas are also covered with PVC foil on all four sides. Glazed doors are equipped with glass (GOST 111 / GOST 5533 / GOST 7481), thickness 4mm (8 mm), inserted through the upper groove of the door leaf.
3. Completeness
4. Doors are supplied to consumers in their original packaging, separately door leaves and separately frames, platband. By agreement with the consumer, the doors and the door stock can be completed with accompanying fittings.
5. Doors of full factory readiness should have a final finish that does not require additional work, installed, glass and gaskets.
6. The delivery set should include: a document on quality (label on the package) and instructions for operating the doors, including recommendations for installation.

1. Marking
2. Each product is marked with a waterproof marker or thesea cat, indicating the name of the manufacturer, nameproduct, date of its manufacture and (or) order number, sign(stamp) confirming the acceptance of the product by the technical control lem.

The markings must be clear and legible. The method of applying the marking must ensure its safety during transportation and storage.

1. The door devices included in the product must be labeled in accordance with the regulatory or technical documentation for this product.
2. It is allowed to give the marking in the accompanying document for the delivered batch of doors, and on each door indicate only its designation.
3. The accompanying document for the delivered batch of doors must indicate:

- name and (or) trademark of the manufacturer;

- name and (or) symbol of the door;

- batch number and date of manufacture;

- Number of doors;

Door size;

- designation of these technical conditions.

1. Transport marking - in accordance with GOST 14192.

Transport markings of glazed doors must include a handling sign “Fragile. Carefully".

It is allowed to apply other handling signs and information labels to ensure the safety of doors during loading and unloading operations, transportation and storage.

1. Package
2. Doors should be packed in accordance with the manufacturer's drawings. Packaging should ensure the safety of products during long-term transportations and multiple transfers of warehouse storage in compliance with precautionary measures.
3. The finished sheet is packed in corrugated cardboard (GOST R 52901) from all 4 end sides.
4. Before transportation, door leafs must be securely fixed with strips, ties or other devices that do not cause damage to the products.
5. Packed doors can be stacked horizontally or installed vertically on wooden pallets in accordance with GOST 9557, GOST 9570, GOST 22831, GOST 26381 and fastened in accordance with GOST 21650. Door foot height is not more than 1000 mm. The pallet design provides for installation in two tiers.
6. By agreement with the customer, it is alloweduse of other types of packaging materials, as well as delivery of unpacked doors.

6. MANUFACTURER'S WARRANTIES

1. The manufacturer guarantees the compliance of the doors with the requirements of these technical specifications, subject to the transportation and storage conditions established by these technical specifications, as well as the installation instructions.
2. The warranty period is 1 year from the date of completion of installation work.

To choose high-quality wooden doors, you must definitely ask the seller for a certificate. If it is, then you are dealing with the products of a responsible manufacturer that complies with all technical conditions and standards.

It should be noted that certification of wooden doors is not a mandatory procedure, only those manufacturers who are confident in the quality of their products voluntarily undergo it.

And if the product still has a certificate - wooden doors and all elements of their construction are made in accordance with the requirements of GOST. This means that you will not have to deal with repair or replacement of doors in the near future.

It is regulated by GOST 6629-88. The presence of a certificate of conformity to this standard means that the door is made in compliance with the technology from quality materials.

In addition, this GOST on wooden doors determines the parameters of fasteners, glazing (if provided), installation in the opening, etc. Despite the fact that these standards have been used for a very long time, and over the years that have passed since their adoption, many new finishing materials have appeared, there have been no major changes in the basic technology of door production.

As before, today in the first place are the requirements for the quality of wood and permissible deviations from the given dimensions.

Do not think that GOST applies only to domestic production of wooden doors. Imported products are also subject to regulation, for this there is an International Standard for doors for residential, administrative, public buildings.

All components of the wooden door block, up to the gaskets or glass inserts (see), must be checked by the manufacturer for compliance with the manufacturing specifications. The results of this check are recorded in the accompanying documents.

Types of structures regulated by GOST 6629-88

In our houses, the most common type of doors are panel doors with a small-hollow filling. Noise and thermal insulation properties (see) of such a door depend on the type of filling, and its decorative characteristics depend on the quality of the finish.

But there are also parameters such as functionality and strength, which are determined by the observance of all standard sizes of individual parts and their correct layout. If you look at the passport, which is attached to each batch of doors, you can find in it designations completely incomprehensible to an ignorant person.

For example: DO20-16 LP GOST 6629-88, PG21-10 N GOST 6629-88. To decipher them, you need to know the GOST classification of wooden doors:

• First letter D Is a door, and P is a door leaf without a box.
• The second letter means the type of construction, where G is a blank canvas, Y is a reinforced canvas, O is glazed, and K is a swinging one (i.e., capable of opening in any direction relative to a fixed axis).
• The numbers following the letters are the height and width of the opening in decimeters.
• Letters after the numbers indicate the design features of the door.: P - threshold, H - overlapped, L - opening to the left (opening to the right is not indicated in any way).

Thus, the code DO20-16 LP GOST 6629-88 denotes a double glazed door for an opening with a height of 20 and a width of 16 dm, opening to the left, with a threshold, made of wooden doors according to GOST. At the request of consumers, the standard allows the manufacture of a door block of other sizes, as well as different widths of canvases for double-sided blind or glazed doors.

At the same time, the consumer should be aware that the entire door block, that is, the door leaf and the frame, must be made from the same type of raw material and supplied in a complete set.

GOST guarantees practicality and convenience

The buyer himself chooses the type of finish of the wooden door and the type of its design, focusing on his preferences and the feasibility of installing just such a door. But it is difficult or even impossible to check the quality of the internal elements of the door if the supplier does not provide a wooden certificate for the doors.

Having a certificate of conformity with regulatory requirements gives the buyer confidence that all the technical requirements for the manufacture of this door model have been met.

GOST defines:

• Height of door hinge placement
• Height of placement of locks (see) and handles
• Methods of fastening door fittings
• Location of fillers
• Frame rib thickness
• Methods for connecting piping, etc.

These requirements did not arise out of nowhere, but from many years of experience in operating doors and trial tests, which made it possible to determine the most convenient parameters from a functional point of view.

The location of the devices at the points indicated by GOST allows you to optimally distribute the efforts applied to them on the entire door structure. That is, from the standpoint of maintaining the integrity of the door, the expediency of these standards is clear.

The rigidity of the structure, the preservation of geometric parameters and noise absorption depend on how correctly the fillers are located in the body of the door - fiberboard strips, bars, paper honeycombs.

GOST 475-78

Do not think that GOST for wooden doors is necessarily monotonous shapes and textures, boring colors. In fact, the compliance of the door with the standard means only that it is assembled from quality materials in compliance with the assembly technology.

For this, there is GOST 475-78, which regulates literally all the nuances of manufacturing wooden doors, including quality control of raw materials and even the size of fastening screws. But this does not prevent manufacturers and designers from creating a variety of models that amaze with their design.

Classification of doors according to GOST 475-78

According to this standard, wooden doors differ in:

• Design features
• Appointment
• Method and direction of opening
• Number of canvases
• Finishing type (see)
• The presence of glazing

For interior doors, properties such as ease of opening, resistance to mechanical stress are important, while complete sound insulation or increased strength are additional conditions. In the presence of a non-standard high opening, it is not always necessary to make a door to order, since GOST on wooden internal doors provides for the option of manufacturing a standard door with a transom.

It can be either dull or glazed, which is an additional source of natural light. According to the number of leafs, doors can be single and double-sided, for double-sided doors, it is allowed to manufacture canvases of different widths.

In the direction of opening, swing doors are distinguished into right, left and swinging - turning in any direction around the vertical axis. Sliding and folding doors can also be right or left depending on which way they open. When buying a door, it is important to pay attention to the method and direction of its opening.

GOST establishes the following standards for internal wooden doors:

• For rooms with constant high humidity (more than 60%), installation of moisture-resistant doors is required. They are made from coniferous wood.
• In rooms with normal humidity, doors with normal moisture resistance are installed. They are typically made from durable, hard, decay-resistant hardwoods.

As for the finishing, it is carried out with transparent and opaque coatings. Transparent varnish refers to opaque ones - various paints, enamels, decorative film and sheet materials.

Special requirements are imposed on the front surfaces that are visible during door operation.

Technical conditions

1. How well a wooden door performs its function depends on its correct geometry. In connection with this GOST, the maximum tolerances for sagging, deviation from the plane of the canvases and the vertical are determined, which are measured in millimeters. It is almost impossible to notice these changes with the naked eye, they are determined by measurements using special tools. But in production, they must be fixed and if the tolerance is exceeded, the doors are rejected.
2. In addition, the technical specifications determine the permissible number of wood defects per unit area - cracks, knots, resin pockets, which must be sealed with corks of the same material, putty and sanded. In short, the surface must be ideally prepared for subsequent coating.
3. For small-hollow filling, slats and bars with defects and rot are not allowed. All non-front (invisible during operation) door surfaces must be treated with an antiseptic or painted.
4. It is unacceptable to use different woods in one model: the material of the frame must be identical to the material of the door leaf. In addition to preserving the decorative effect, this guarantees the normal functioning of the door.

Let us repeat that if you are offered to study the certificate when purchasing, the wooden doors are made in compliance with all of the above technical conditions. In addition, the certificate of conformity guarantees that during the manufacturing process the quality of finishing materials, the strength of adhesive and spike joints, and the correct installation of devices were controlled.

GOST 475-78 specifies the application of the relevant standards and specifications for each door assembly unit. In the passport of each batch of doors, the test results, measurement data and specification for the parts supplied not assembled are entered.