Often people are faced with a question such as installing a gas hob with their own hands. A kitchen set, as well as an oven and a gas stove, are not cheap pleasure these days. People who spend large sums of money on furniture renovation want to save the family budget by installing a gas hob. To carry out this work, you yourself need to take accurate measurements and find out a few nuances for installing equipment.
How to markup correctly?
The key to a successful installation of the gas hob is the correct marking. The appearance of the kitchen set will depend on this stage of work. A protruding or crookedly installed panel will immediately catch the eye. It is unacceptable to make mistakes in the markup. Even one centimeter can play a decisive role in the installation. If you cut off more from the countertop than necessary, then it will have to be changed. In our time, the countertop is the most expensive part of the kitchen set. When installing the panel around the edges, there is no margin, so it is necessary to cut it out with an accuracy of millimeters.
The place for the hob can be marked in two ways:
- Put it on the table top, draw a pencil around the contour. This method is considered the simplest.
- Make accurate calculations. This method will help you avoid errors during installation.
How to calculate correctly where the place should be?
The installation of the gas hob in the worktop must be carried out when the place has already been marked for it.
Calculation plan:
- On the countertop, the inner edges of the drawer are marked, above which the panel itself is placed. You will get two parallel straight lines. If you mentally connect them to the edges of the countertop, you get a rectangle.
- With a pencil, you can draw thin lines diagonally. This is the center of the rectangle. The next step is to build a coordinate system. It turns out that in it one line will run parallel to the outer edge of the countertop. Another line will be perpendicular to it.
- When the coordinate system is ready, the coordinates of the hob are marked on it. For this, the panel must first be measured. The obtained values \u200b\u200bmust be taken with a small margin.
- When the points of the future panel appear on the coordinate system, four straight lines need to be drawn through them. It turns out that two of them run parallel to the table top, and the other two are perpendicular to it.
- The result is a rectangle that needs to be cut out. A hole will remain in which the hob will be installed.
What tools are required to cut a hole?
The installation and connection of the gas hob requires certain tools. To cut a hole for the hob, you will need at least three tools: a milling machine (preferably hand-held), a jigsaw, and a drill. To get the perfect hole, it is best to use a hand-held router. If such an apparatus is not at home, then it is permissible to use a jigsaw. In the absence of the item you are looking for, you can purchase it at the nearest hardware store. The price of a jigsaw is affordable for the average consumer.
You should stock up on a set of screwdrivers. A knife and spatula will come in handy. If there is a set of wrenches, then it must also be prepared. Every homeowner should have a drill.
Materials for installing a gas hob
It is worth stocking up with scotch tape, as well as silicone sealant. You should not save on waterproofing if you want the slab to serve for a long time. It is better to take an imported sealant.
A gas coil is required to connect the panel. You will need to buy a special steel hose. It must be sold with a certificate.
How to cut the hole in the right shape?
Start cutting the hole with a drill. As a rule, sloppy edges are obtained, which have to be corrected afterwards. It is better to take drills from 8 to 10 millimeters. Gradually, many holes are made around the perimeter of the future panel. Then, using a drill, a slot is made at the same time. It is important to understand that you can only drill from the inside of the countertop.
When the piece falls, it can damage the kitchen unit. Better to put a chair or cabinet under it. Cutting with a jigsaw is much easier than cutting with a drill. First, you need to mark the hole that the person will cut with a drill. It is permissible to do it without using a drill.
Care should be taken when working on installing the gas hob. It is important not to injure yourself or damage the furniture.
What is waterproofing for?
Installing a gas hob is never complete without waterproofing. When the work on cutting out part of the countertop is completed, waterproofing must be done. It is important that water does not get onto the countertop. Under its influence, it can deform. The material can swell by absorbing water. Silicone is usually applied to the cut site.
How to choose the right hose when connecting yourself?
It is important to be aware of the danger of connection work, entrust this matter to specialists or work independently under the supervision of a qualified gas service worker.
The main task is to choose the right hose. Before purchasing, it must be checked for defects. A certificate must be included with the hose. It is issued in the store.
You can purchase either a metal hose or a rubber hose. The second option costs less than the first. They are usually monochromatic.
How to connect the gas hob yourself?
The rules for installing a gas hob are important recommendations of professionals that will help to achieve the perfect installation of the chosen model:
- Before starting work on the connection, you must open the hob and check if there are any defects on it. It is important that the device is not mechanically damaged.
- The hob must be placed in the hole. Then you need to connect the gas hose to the gas pipeline. Professionals recommend using a winding at this stage. In this case, the risk of the danger of gas leakage is significantly reduced.
- When the hose is connected, you must try to open the gas cock. It is required to prepare a soapy solution to apply it to the winding. This method helps to determine if there is a gas leak.
- If the foam does not move and bubbles do not appear, it can be said that there is no leakage.
- The next step is to connect the hob itself to the connection. It is worth trying to open the burners one by one. The air should come out, usually it takes one minute.
When connecting, it is better to use long hoses, at least three meters. Sometimes people are installing a gas hob and an oven at the same time.
Thinking about making your own kitchen furniture? Then it's time for you to find out that making it is only half the battle, and the second half of this business is to complete the furniture with all kinds of equipment. These are built-in washing machines and dishwashers, and a sink, and an oven, and, of course, the hob, which will be discussed in this article. Together with the site okuhne.net, we will deal with the question of how to install the hob with our own hands and how to connect it to the home gas pipeline and electrical wiring.
Hob installation photo
Installing the hob: marking the installation site
Marking is perhaps the most important stage of work associated with installing the hob with your own hands, which, oddly enough, has the most nuances. Judge for yourself - the whole appearance of the kitchen depends on how clearly and accurately you can mark, and then cut a hole for the hob. This is exactly the case in which an error of one centimeter may be irreparable - you should always remember about the cost of the countertop. Buying a new one isn't all that cheap. The fact is that the panel itself should fit clearly above the curbstone, and there is practically no margin in width.
There are two ways to mark the bore hole - you can simply lay it on the tabletop, center it on the peephole and circle it with a pencil, or go the way of professionals and calculate everything down to a millimeter. Naturally, it is better to choose the second option for solving the issue, since in this case the chances of making a mistake are minimal. This is done as follows.
Now it's just a small matter - cut and install the hob into the hole. We will talk about this further. For those who do not like to read and delve into what has been written, we attach a video on installing the hob in the worktop.
Gas hob installation: two ways to cut a hole
You can cut a hole for the hob using three different electric tools - a jigsaw, a drill or a hand-held milling machine. The most accurate and beautiful cut is obtained using a hand mill, but you don't even need to ask about its presence in the home workshop of a person who is not associated with construction. Not everyone can find a jigsaw either, but at least it is not very expensive, and you can buy it for these works. Well, almost every household man has a drill. Let's start with it, but first I will warn about the quality of the hole obtained with a drill - it can be said to be disgusting. It is quite difficult to seal torn edges, but this must be done, and problems will arise in this regard. In principle, they are solvable, but more on that later.
After the hole is ready, it is imperative to waterproof it - if water or even just moisture gets into the end of the countertop, there is a very high probability that the material from which it is made will swell and the countertop will deteriorate. As a rule, the end of the cutout is treated with silicone. If you cut a hole with a drill, then it will be quite difficult to do it efficiently - you have to tinker.
Installing the electric hob: fixing and connecting
To make it easier to understand how the hob is installed in the hole in the countertop, we represent it as a sequence of work - so to speak, in the form of a small but understandable instruction for installing the hob.
Basically, that's it. The electric hob is mounted in exactly the same way. The only exception is the absence of a gas hose in it. There may, of course, be other nuances - for example, if we talk about an oven-dependent hob, then the installation process looks somewhat different here. To begin with, the oven is installed, and then the panel, which is connected directly to the oven itself.
Basically, that's it. Now judge for yourself whether this work is difficult or not. You will cope with it yourself, or perhaps contact the specialists. In general, based on experience, I can say that most people who are wondering how to install the hob with their own hands, cope with this work easily. In fact, it is not difficult, and all that is needed for the successful completion of the case is to strictly observe all the subtleties and nuances.
If you want to make repairs in your kitchen, then you can independently replace the stove with a hob. Today, a modern and functional solution for every kitchen is to install the hob in the worktop with your own hands. In addition, you can make a combination that will consist of an oven and a hob, so you do not lose anything at all. In this article, we will tell you in detail how to independently install the hob in the countertop without the help of specialists.
If you have ever had to do repairs at your dacha or in an apartment, or you have been engaged in construction, then correctly installing the hob in the countertop will be a simple matter for you. It is enough to accurately measure its thickness and dimensions during installation. Well, let's get started.
In order to properly install the hob yourself, you need to know how to cut a hole in the worktop. All the required sizes are noted in the instructions on the diagram, do not come up with anything new. So, you will speed up the process and significantly reduce the likely measurement errors. Measurements can be made independently, for this you need to put the hob from the bottom to the top, then find out the length and width of the surface on the sides inside.
Please note that the instructions write the minimum allowed indents from the edge of the tabletop. You can make the size of the indents a little larger, since the narrow edges may break after a while. It is necessary to make markings on the surface of the table in accordance with the dimensions and thickness of the hob. This is where you will embed it. To keep the lines visible and more noticeable on a dark surface, you can glue strips of paper tape, and transfer each line to them.
Then you need to drill a hole from which the cut begins. Cutouts are made with an electric jigsaw. To make the edges of the cutout even and not crumble along the edges, it is advisable to use a hand router, and round the corners with a radius cutter, while each cut must be sanded. The resulting sawdust, you can collect with a vacuum cleaner.
When you are done with the hole, take your hob and make sure you cut it correctly. If you carefully cut the hole, the surface will easily fit into the resulting cutout. 
We seal and seal
Before installation, it is necessary to process the sections of the countertop with a silicone sealant or nitro varnish. So, you will protect the surface of the countertop from water, dirt stains, swelling and extend its service life. You can also use a seal for installation, since it glues itself and performs the same role.
The self-adhesive seal is placed on top, the edges of the surface should lie on it. You can also use aluminum tape for sealing, which, by the way, protects against temperature fluctuations. If the seal is of high quality, then the hole in the countertop will serve you longer, it will not need to be repaired or replaced.
Also, the installation differs depending on the type of panel - they are gas and electric, plus separate fastening characteristics. You can fasten the fastening parts with screws.
Today's electrical panels are very functional, with proper surface installation, they rarely fail, therefore, they do not need repair work for a long period. When repairs are nevertheless needed, the panel quickly detaches and refers to the master on its own, or the repair can be done independently, thanks to which you save your money on calling a specialist.
Before installing the hob, place it on the worktop, turn it over and connect the wires according to the diagram. You can find the diagram on the back of the panel, this is done for your convenience. It is necessary to take into account not only its size, but its thickness. When you install and connect yourself, then take good care. If you connect the wires incorrectly, then you will not then adjust the burners and their heating value.
If there is a special panel wire to connect the hob electrical panel, then you do not need either an outlet or a plug. It is enough to connect the panel to the wire. The connection of an induction hob follows the same principle.
When installing a gas hob with your own hands, you need to see the type of fastening. Do not forget about the thickness and dimensions of the hob. Then it must be installed, aligned along the edge of the tabletop, and then secured. As a rule, the kit includes brackets for fastening, they are located at the bottom. The electrical wire is plugged into an outlet.
To connect a gas hob with your own hands, you need to carefully study the safety rules. The gas is shut off, after which the hob is connected with a flexible hose to the gas pipe. A paronite gasket must be placed in the nut. Then turn on the gas and the burners, check the hose connections so that there are no leaks. To do this, you need to soap all the joints, if the foam does not have bubbles, there are no leaks, the installation is done correctly. In addition, gas analyzers are used for testing.
If you do everything correctly, then there should be no problems installing the hob. The main thing is that you do not rush and do the job efficiently, taking into account all the nuances of installation.
This is a step-by-step instruction on how to cut a hole in a chipboard or mdf countertop under the hob with your own hands. When you probably need to know how to cut holes in chipboard or MDF countertops if you are installing a sink or hob. This task may seem simple, but we can assure you that there are many nuances that need to be considered for a good result.
On the one hand, you must closely follow the contour of the gas stove using a template or follow the instructions indicated on the product. In most cases there are certain restrictions that you must pay attention to, for example, the minimum distance from the stove to the back panel or from both sides, to. Use a large L-shaped square to draw a rectangle on the desktop, otherwise the corners will not be right angles.
To get an accurate hole, you have to use a good saw with the correct blade. Therefore, the blade must have teeth oriented downward, otherwise it will split the surface. Drill starting holes along the four corners of the rectangle using a drill or (the hole should be wider than the size of the jigsaw blade).
Work plan for installing the hob in the worktop
Materials:
- countertop;
- carpenter's pencil;
- insulating tape.
Tools:
- Protective gloves, goggles;
- Saw or jigsaw;
- Roulette, level, square;
- C-clamps.
- Wear safety glasses when making incisions.
- Choose a blade with fine teeth.
Deadline
- 10 minutes
When installing a gas stove or hob, you must cut holes in the worktop.
Tip: follow the manufacturer's instructions when cutting a hole in your kitchen countertop if you want to prevent possible problems.
How to cut a hole in the worktop for the hob
Marking guide linesThe first step is to define the contour of the slab. In most cases, it should contain instructions on how to do this, but there is a technique in which only the recommended hole sizes are indicated. Place the hob on top of the cabinets. Leave the recommended distance from the back panel to the front edge of the table top.
Draw a median on the countertop and mark the incision lines using the manufacturer's instructions.
Marking the countertop for the hole for the plate As you can see in the picture, you need an L-shaped square, tape measure, and a carpenter's pencil to get the job done professionally. Make sure the cut lines are parallel and at right angles. Also, the rectangle must be symmetrical.
Tip: Check that the rectangle under the kitchen unit where the hood will be built-in is correctly positioned and that there is sufficient space around it (according to the manufacturer's instructions).
Installing spacers under the countertop To get an accurate result, you must place some spacers under the countertop. However, the table top should be flat.
You must leave about 5 centimeters of free space between the cabinets and the countertop, otherwise the saw blade may damage them.
Making initial holes for drilling Use a drill with a special drill bit to create starting holes along the corners. It is very important to align the bits correctly, otherwise you might drill out of the contour.
Tip: Make sure you are using good RPM drilling equipment. Set the drill at low speeds and hold the drill with both hands if you want good control over it. Repeat the process for each corner of the rectangle.
Passage of the laminated layer In this image, you should notice that the drill goes through the top layer. Do not use too much pressure on the drilling equipment, otherwise it may slip out of place.
We remove the remains from the process with a vacuum cleaner Drilling a hole in the countertop with a drill will create a lot of residue, so we recommend that you ask someone to remove them as you are making the hole.
Tip: Work with great care and attention as it is important to make the holes exactly in the indicated places.
Cutting holes in the worktop After drilling the corner starting holes, cuts should be made along the guide lines. If you are not experienced in this area, you should cover the cut lines with masking tape. This way, you will help prevent edge chopping.
Cutting a hole with a jigsaw in a tabletop We recommend that you use a jigsaw to make cuts. Choose a blade with teeth pointing down. In addition, the blade must have parted teeth. If you have not worked with a jigsaw before, we recommend that you secure the table top. Make sure the blade runs exactly along the cut lines.
Tip: Remove the chips that form frequently, otherwise they may cover the lines. Set the jigsaw at low speeds.
Finished hole in the worktop for the stove Last but not least, you need to take care of installing the hob in the countertop with your own hands. If you've followed our advice and read the manufacturer's instructions, the hob should fit easily into the hole. However, if the edges are not perfectly straight, you can smooth them with silicone or sealant.
Tip: Use sandpaper to smooth out the cutting edges.
Installing the hob into the worktop After that, you just have to install the hob in the worktop, connect it and fix it with the screws that should come with it.
Thank you for reading our step-by-step guide on how to cut a hole in the worktop and install the hob with your own hands, we recommend that you read other articles. Don't forget to share our designs with your friends using social media widgets.
The idea of \u200b\u200binstalling your hob yourself can be a little daunting. After all, you will have to deal with either electricity or gas and at the same time work with rather expensive kitchen equipment. However, none of the steps to install the hob is particularly difficult. You just need to do everything carefully and in the correct sequence from the beginning to the end.
Steps
Installing the electric hob
- To disconnect the hose, turn its nut counterclockwise.
-
Connect the gas hose to the new hob. Use a gas sealant by applying it to the threads where the hose and the hob join. Apply sealant generously to the threads, but so that it does not get into the hose. Use a wrench to screw the gas hose nut onto the hob.
Place the new hob in its place. Lower the hob carefully into the opening to avoid damaging any connections on the bottom. Before lowering the hob into the opening, you must pass the gas hose forward.
Connect the gas hose to the stationary gas pipe. Apply sealant to the threads of the gas pipe fitting. Then tighten the gas hose nut with a wrench. Be sure to tighten the nut tightly.
Prepare a soapy solution. Prepare a solution of 1 part dish soap and 1 part water to check for possible gas leaks. Stir the solution thoroughly and then either spray it on the gas connections or apply with a brush. Turn on the gas supply valve by placing it in the position in which its handle indicates the direction of gas supply.
Switch on the cooking zones and test them. If a soapy water test shows no leaks, try lighting the burners. It may take a few seconds for the gas to come up and ignite, as normal air must first come out of the hose.
-
Attach the hob mounting brackets to the worktop. When you are sure that the hob is working, attach it to the worktop using the fixing brackets. Your hob is now fully installed.
- Replace the doors and drawers of the cabinet under the hob and all of its contents.
Remove the old hob, if any. If you are replacing an old hob, first you need to remove it. Cut off the electricity in the switchboard. Remove any attachments from the hob and clean off any existing sealant. Disconnect the wires, remembering how the old hob was connected, and remove the hob from the hole in which it sat.
Make sure you have enough space in the location chosen for the hob. Ideally, you should have a gap of 76 cm above the hob and approximately 30-60 cm on either side of the hob.You should also ensure that there is enough space under the worktop to accommodate your new model. hob.
Make sure there is a junction box near the location you have chosen to connect the hob to the mains. Most electric hobs require a direct connection to the mains through a 220 V junction box. If you are replacing the hob, you probably already have a junction box.
Measure the hob and make sure it fits into the old hole. If you are replacing the hob, there should already be a hole in the worktop, and you just need to make sure that it fits the new hob.
Adjust the hole for the hob to fit into it. The hole should be 1.5-2.5 cm smaller on each side than the hob. If you do not already have a hole for the hob, or it is too small, then you will need to cut it to the desired size. If the existing hole is too large, then metal sheets can be screwed on the sides to reduce it.
Remove all removable parts from the hob to make it easier to replace it. The hob may have removable burners, protective screens and other parts that should be temporarily put aside. You should also remember to remove all packing materials from the hob.
Install the clamps. They are designed to fix the hob. You should hang them from the top edge of the slot and then screw them down.
Lower the hob into the opening. Lower the new hob into the hole, making sure to insert the wires first. Press down on the hob until you hear the locking clips click.
Connect the hob wires to the mains. Electricity should still be turned offwhen you do this so as not to get an electric shock. Connect the hob wires to the corresponding wires in the junction box.
Refit the previously removed removable parts on the hob. Replace the burners, guards and other removable parts.
Turn on the electricity and check the hob is working. Turn on the power to the hob to check that everything is working properly.
Open all cooking zones for a few minutes. Despite the fact that you have turned off the gas, it may still remain in the hose. Open all burners to release gas. Don't set it on fire. All gas will be released in a few minutes.
Disconnect the flexible gas supply hose from the stationary gas line using two wrenches. Take one wrench and install it on the hose nut and the other wrench on the fixed gas line nut.
Remove all removable parts from the hob. Remove hotplates, protective shields and other removable parts before proceeding further. This will make it easier to move the hob.
Remove the clips securing the existing hob in place. Unscrew the clips on the underside of the old hob.
Push the hob from underneath to raise it. Remove the hob from the worktop and put it in a safe place. Remember that the gas hose is still connected to it.
Disconnect the gas hose from the old hob. If you will be using an old gas hose to connect a new hob, you must disconnect it from the old hob. Use two wrenches to do this, placing one on the hob and the other on the hose nut.