The question of how to start a chainsaw can be divided into two parts:
- Factory according to the instructions
- What to do if you can't start
The information from the first part will be useful to those who have lost the instruction, or to those whose instructions are uninformative.
The second part will tell you what to do if you did everything correctly according to the instructions, but the chainsaw still does not start. It will also be useful for those who have a chainsaw that does not start well.
1. Start the chainsaw according to the instructions
Different chainsaws can be wound in different ways. Let's analyze the two most popular mechanisms that are used to start a chainsaw that exist today. For example, let's take Stihl chainsaws MS 180 and Echo CS-352ES. If you have a chainsaw of a different brand, then just try to start by analogy, since most likely you have the same or similar mechanism.
Before starting the description of the winding process, I would like to note that for some chainsaws, the instructions say that before starting the chainsaw, you need to turn on the emergency stop brake. Sounds like it's safer. However, with a fixed brake, it is more difficult to start a chainsaw, so it is better to unlock it. If you do everything wisely, then the chainsaw will not do anything to you during startup. If you are afraid that without fixing the brake, the chainsaw, when you try to start it, can harm you, then it’s better not to take this tool at all.
So let's start with the Stihl MS 180.
Now we will analyze the second second mechanism that allows you to start a chainsaw.
2. Why won't the chainsaw start?
If you did everything according to the instructions, but the chainsaw still does not start, then something is wrong with it. This may be due to several of the most common reasons: no spark; fuel is not supplied; clogged air filter. So, below we offer a procedure that will help identify the reason why the chainsaw does not start.
What to do if your chainsaw does not start
The first thing I would like to note, if your chainsaw does not start, do not turn any screws on the carburetor. If you are not a specialist, you still won’t be able to set something up on your own and you won’t be able to start a chainsaw.
Perform the following actions necessary to start the chainsaw in the order indicated, starting to do the action under the next number only if the previous one did not help.
- Try to start by just leaving the chainsaw alone for 5-10 minutes. Perhaps during the winding she had a candle filled - it happens. Then try to start again according to the instructions.
- Remove the housing cover on the chainsaw, remove the air filter and try to start without it. If the filter is dirty, it should be washed in soapy water and dried or replaced with a new one.
- Remove the spark plug from the chainsaw. Check for spark. If there is no spark, then try a new spark plug. If the spark does not appear, then this means that the ignition unit is damaged and the saw must be carried in for repair. True, visual observation of a spark does not mean that the ignition unit is working. If there is a spark, but the chainsaw did not work, do the following steps in the list.
- If there is a spark, but the spark plug is wet, then turn the chainsaw over to drain excess gasoline from the cylinder if it has accumulated there. Pull the starter without a spark plug 10-15 times to ventilate the combustion chamber. Ignite the candle and screw it back, but rather change it to a new one, if any. Again try to start according to the instructions.
- If the candle is dry, then draw one or two cubes of gasoline mixture into the syringe and pour it into the cylinder. Try to start a chainsaw - perhaps a small speck has got into the carburetor, which prevents fuel from entering the combustion chamber. It is quite possible that this mote will be pulled out by the flow formed after starting the chainsaw by adding fuel directly to the cylinder.
- Unscrew the muffler and remove it, being careful not to damage the gasket between the muffler and the engine. Try starting without the muffler and air filter. With the silencer removed from the chainsaw, you can inspect the piston from the inside. If there are burrs or burrs on the walls of the cylinder or piston, or the ring on the piston is jammed with burrs, then you will have to be very upset, as this means that the piston is damaged or worn out. This usually happens with underfilling in fuel mixture oils. With such a malfunction, you will have to contact the service, and possibly think about buying a new chainsaw, since replacing a piston one is a rather expensive operation.
Thus, we have analyzed in this article how to start a chainsaw “according to the instructions”, and also what to do if the chainsaw does not start. We hope you find these tips helpful.
It would seem that it could be easier than starting a chainsaw and working with it. But, as in any process, there are many pitfalls here. Follow safety precautions, and starting a chainsaw will not be something supernatural for you. Accordingly, a manual is attached to each type of saw, which must be studied before performing work. The instructions describe in great detail how to use the saw, how to prepare it for work and how to start it. You need to be very careful about the concept of running a chainsaw. For two-stroke engine tools such as chainsaws, the concept of break-in does not exist.
Before starting the chainsaw, it is imperative to check the engine brake. It must be enabled.
By running in the engine, we mean the operation of the first two or three hours in a gentle mode. Work should not be carried out at maximum speed, do not immediately cut heavy material, thick trunks and logs. The first hours of the new tool can be cut branches, knots, softer wood, so that new parts get used to each other as much as possible. Good modern chainsaws are made in such a way that they do not tolerate long idling, therefore, if the saw is not currently in use, then the engine must be stopped.
Fuels and lubricants for chainsaws
The process of preparing the fuel mixture must be approached very responsibly. Chainsaws use gasoline not pure, but mixed with two-stroke oil. The oil must be of high quality and burn without consequences during operation. The mixture is made in a percentage of 1 to 50, in other words, 20 g of oil is added to 1 liter of gasoline. It will not be difficult to measure a liter of gasoline, and to prepare exactly 20 g of oil, you will need a measuring cap or an ordinary medical syringe. After adding the oil, shake thoroughly to make the mixture homogeneous.
When it is important not to confuse the filling containers. On the gas tank, a distinct pattern of a filling column is printed. Filling is preferably done with a funnel to keep the tool clean. An additional mesh is also desirable on the watering can to prevent excess dirt from entering the tank. We must not forget that the chainsaw provides for the use of oil to lubricate the chain. Any clean, unrefined oil with an approximate viscosity of 15-30 is suitable for this.
Oil is poured into a separate tank located near the tire. When pouring, also use a watering can or syringe. Chainsaw oil must be present at all times. Periodically, you need to lubricate the bearing, which is located at the end of the tire. This can be done with the same syringe through a special hole. The saw is ready to work, you can start running. To minimize the possibility of accidental ignition, it is recommended that the saw be started in a location that is separate from where it is refueled.
Back to index
Preparing and starting the saw
The handle that controls the throttle, in a simple way the throttle button, is located on the back side of the handle. To avoid accidental start of the engine, pressing the gas button, you need to press the lever - the throttle lock located on top of the handle. At the bottom of the saw is a chain catcher, in the event of a chain break, it captures it, protecting the operator from serious injury.
With the help of the stop button, it is also called the ignition, you can quickly turn off the engine, it is located in a convenient place. The chain brake lever can be activated with two different ways. Method number one is manual, you only need to push the brake handle forward, the second method is inertial, in the event of a kickback during a rebound. You will need to make sure that the chain tension is correct, that it is not too tight, but also does not hang from the bar. The newly put on chain must be tightened after some time of operation of the chainsaw.
When starting the chainsaw motor, we install it on a flat surface, the place under the tire must be cleared of foreign small objects. Having set the chain brake to the ON position, we move the handle of the inertial brake forward, depress the "smart start" button, if this function is present. When starting a cold cold engine, always fully close the choke by pulling the regulator towards you.
The right foot steps with the toe on the bottom of the rear handle. Holding the upper handle with your left hand, with sharp, but moderately strong movements, pull the starter cord by the handle, continue until the engine gives the first signs of starting. Now the damper must be fully opened by pushing the regulator. We continue to pull out the starter cord. It will be enough to make two or three jerks for the saw to start. Press the gas button once, after which the engine should stop idling.
To start a running and hot engine, there is no need to use a choke. All other points for starting the saw will be exactly the same. It happens that it is difficult to start the saw even on a well-heated engine, you need to pull out the regulator to the end, as you did when you started the cold engine, but immediately push it back.
After starting the chainsaw engine, it is not necessary to remove the chain from the handbrake until the start of work. It will be important to check the chain for lubrication. You will need to use some kind of light plane, whether it be a stump, paper or a light rag. We increase the chain speed a little, a path of engine oil is formed, which will indicate sufficient level oil in the saw tank.
Try to hold the chainsaw firmly with both hands, all fingers should completely cover both handles. To minimize the force of a kickback - rebound, left hand should completely encircle the front handle, thumb is right below. Never be afraid of a saw, the closer you hold it to your body, the less you will feel the actual weight of the saw. Better balance and control over the instrument will be maintained.
When moving from one place of work to another, you need to be sure that the chain is in a stationary position. To do this, always apply the chain brake, and it is better to stop the engine. When traveling even longer distances, wear a protective cover over the bar, this will protect you from accidental injury and help protect the chain itself. After completion of work, it is recommended to drain the fuel mixture and store the chainsaw with a dry tank. It is important not to forget that the fuel mixture is prepared for 7-10 days of maximum use. The mixture has its own shelf life and after 7 - 10 days loses its properties.
All chainsaws from the Shtil manufacturer have two-stroke engines. They are carried out according to a similar algorithm. However, on sale you can find models that have optional equipment, with it you can start the saw without applying special efforts. For this reason, the starting method may differ.
Algorithm for setting the saw "Calm 180"
If you are faced with the question of how to start the Stihl chainsaw, then this process can be considered using the model 180 as an example. In order to carry out cold work, you must turn on the ignition and set the engine control lever to the lower position. In this case, the carburetor damper will block the air from the filter, and the throttle will be open, so the fuel mixture will be enriched.
The starter handle must be pulled several times until the first flash occurs. This will indicate that the mixture has entered the cylinder, and the equipment is ready for the establishment. Before starting the Stihl chainsaw, you must set the control lever one position up. In this case, the air damper will open, while the throttle will remain in the same position.
The starter needs to be pulled and started. The tool will run at high speed, throttle valve will be open. To set the latter to idle mode, you should use the gas trigger and release it. The tool should now work normally. On the described chainsaw model, there are no additional devices that would make it easier to start.
This device, compared with the previous one, has some differences in the trigger mechanism. However, there will be no changes in the launch algorithm. The described version of the equipment has a system that, using a spring in the starter of the saw, reduces the resistance of the engine.
We start the MS 211 C-BE brand saw
If you, too, were among those consumers who thought about the question of how to start the Stihl chainsaw, then as an example, consider another model that was mentioned above. In it, the supply system is equipped hand pump, allowing you to start the saw easier on a cold one.
The instruction contains an additional item that indicates that before starting, it is necessary to pump fuel into the carburetor using a pump. Next, you should act according to the principle that was described for the model 180.
Starting a saw after winter
If you are faced with the question of how to start the Stihl chainsaw after the winter, then you should read the recommendations. From consumer feedback, it can be understood that after a long period of inactivity, some users cannot start the equipment. For a successful launch, you need to take care of the saw in advance.
Before storing it, drain the fuel, and then start the engine and burn the fuel that remains in the system. Preparation is necessary so that the membranes do not stick together during storage. This simple operation will allow you to start the saw after the winter. If you still don’t know how to start the Stihl 180 chainsaw correctly, then you should know that it will be easier to do this if you add 2 ml of fuel mixture to the cylinder through the spark plug hole before starting. This can be done with a syringe.
Saw insertion with decompression valve
Users sometimes ask how to start if the instrument has a decompression valve. The 250 does not have one. As soon as the first flash occurs, the valve will be in normal operation. The engine control lever will be set to the position when the choke is open. The launch will continue, the decompression valve must be pressed again. It does not make the launch quick, but it simplifies the process and makes it comfortable, because during the launch the operator will have to make less effort.
If you are not quite sure that you know how to start the Stihl 180 chainsaw, then remember that equipment with a valve, regardless of whether it has a hot or cold engine, must be started using the valve. This will make it easier to crank the engine. So you can extend the life of the starter and reduce the number of broken laces, because such chainsaws have a larger cylinder volume and compression.
Overview of the MC 180 chainsaw
This model of equipment costs 11,490 rubles. It is a household tool that will help you cope with work on suburban area. With the help of the unit, you can get rid of unnecessary knots and cut small trees. The control is single-lever, and due to the low weight, it is very comfortable to work with the unit.
The consumer should be aware not only of how to start the Stihl ms 180 chainsaw, but also of technical specifications. Among others, a 35 cm tire should be distinguished, as well as an engine with a volume of 31.8 cm 3. The volume of the oil tank is 0.15 liters. The equipment weighs 3.9 kg. The power of the model is 2 liters. With. The capacity of the fuel tank is 0.25 liters.
Overview of the chainsaw "Calm 250"
You can buy models 250 at a price of 29,542 rubles. This equipment is a semi-professional model with a 40 cm tire. Power is 3.1 liters. With. or 2.3 kW. The fuel tank capacity is 0.47 liters.
Quite often, before buying, consumers are wondering how to start a Stihl 250 chainsaw. This was discussed above. However, this information is not the only one that should be read before using the model. Other features include:
- single lever control;
- the presence of a compensator;
- anti-vibration system;
- side chain tensioner.
By purchasing this model, you will be able to carry out its quick refueling. This feature is implemented by a lid, which has a patented design. The operator, working with the equipment, will have reliable protection hands Consumers especially highlight also the toothed stop, as well as the chain, which guarantees high-quality and fast sawing of wood.
Conclusion
After purchasing the equipment described in the article, you should ask how to start the Stihl chainsaw. This information will help you extend the life of your tool. After all, improper handling of it can cause rapid wear of some parts. It is especially important to know how to prepare the unit for a long downtime. This was discussed in more detail above. After reviewing such information, you can understand how to prepare the device for winter storage.
Sometimes technical specifications tell some consumers about the launch features. If it can help you too, then you should read them. Some of them were presented above, but their complete list is presented in the instructions, which are necessarily supplied with the equipment.
Malfunctions of the Stihl MS 180 chainsaw and their elimination
Chainsaw in operation Calm MS 180. How to start a chainsaw Calm 180. The problem in the future. Before conservation for the winter, on the advice of mechanics, I dropped 4 drops of engine oil (calm) into the hole of the candle. twisted the candle. At the moment I was going to go to the country, I decided to look at the saw. How to start a chainsaw in the most that after a long idle time of the saw, start it with. I pulled the starter but it won't turn! I turned out the candle, it was in oil, rubbed it back. the same. Turned it over, turned the starter without a spark plug, everything spins completely. Turned it back on and the starter wouldn't turn. What could be?
Rinse the chainsaw with clean, undiluted gasoline, fill directly through the spark plug hole and slowly turn the starter. Later, drain the fuel and the latest. After all these manipulations, dry the saw and the candle, and only then try to start it. Once you have learned to conserve, then learn and re-preserve, and not just pull and go.
Can you tell me why the starter is sticking? The Stihl 180 chain saw is brand new.
You don't understand, you don't know. Maybe the starter cord does not fit well, or maybe somewhere the ebb is interfering. Shtilevsky starters are quite reliable and durable. Any diseases of a constructive plan are not observed, the main thing is either mud or saturated exploitation. Once the chainsaw is brand new, bring it to the service center under warranty and they will repair it.
I saw one feature at my own Stihl MS 180 chainsaw: when gasoline runs out in the tank, the revs idle move increase and the chain begins to spin even when the trigger is released. When you press the gas, the chainsaw stalls. This continues for a couple of 10 seconds, then the chainsaw stops. On motor vehicles, I did not follow such a phenomenon, so that with a lack of fuel in the carburetor, the engine speed would increase. Why is this happening?
This is normal for two stroke engines. With a decrease in the supply of gasoline to the carburetor, the consistency becomes leaner. Consequently. increase in speed, deterioration of acceleration. Accompanying this is a short-term overheating of the CPG. The engine will not disable, but it will not add health. Avoid running out of fuel from the tank to the end.
There is a chainsaw Stihl MS180, used in holiday season at the harvesting of firewood. In the near future, the reaction of the chain began to disappear when you press the gas, the chain does not spin at all, or in jerks. drinking is unrealistic. How to start a husqvarna chainsaw. What could be the breakdown?
For a completely new chain and sprocket, the tension must be exactly according to the annotation. so that the lower branch does not sag. and the upper fingers could be taken out to the height of the leading link. Then the chain will walk quite freely on the tire. But, the gradual wear of the sprocket teeth reduces its pitch. And the gradual stretching of the chain increases its pitch. and there comes a time when the steps of the same sprocket and chain no longer coincide to such an extent that the recommended tension already causes difficult movement of the chain. In this case, we recommend that the tension be slightly reduced. Right up to the appearance of a certain sag of the lower branch. By the way, for the same reason, it is recommended to use a pair or even three chains on one sprocket. In this case, wear is moderate and there will be no accelerated wear of the newest chain on an old, partly worn out sprocket.
Chainsaw Calm 180 after start-up, when you press the gas, it "chokes" and if you start sawing, it stalls. But if you torture with gas for 30-40 seconds, it starts to work normally. developed 3 liters of gasoline, clean filters, oil from the dealer.
If it started not so long ago, then most likely something got into the carburetor with bad fuel. Needs to be cleaned.
I would like to purchase this unit. What should be paid attention to during the inspection?
Not to mention the engine itself, since it is better to diagnose it in the service, you can look at the rest and get a lot of information. Significant mileage will be evidenced by: Dangling latch of the top cover. (Must lock tightly and not rotate from vibration). A brand new star on a battered chainsaw. With the cover removed, the movement of the motor relative to the housing. Sheared chain catcher and chain damage on the sprocket cover. You can also look closely at the carburetor on the left side along the way. where the wire rod enters the choke shaft arm. For a slightly working chain saw, it will be even, oblong. The longer the saw has worked, the greater will be the development of this hole. It rubs through from time to time. Under no circumstances should you take a saw that has at least a small free play of the right end of the crankshaft relative to the motor. This is a sign of an imminent renovation.
How many seconds should the engine run chainsaws Stihl ms 180 at idle before shutting it off?
Let it run for about 20-30 seconds and then turn it off. Their cold start is a review of the ms 180 chainsaw. How to start a Stihl ms 180 chainsaw. More. there's no point.
The idling began to disappear, at first I did not understand what was the matter, and later I remembered that I needed to add a lot idle move I added on a hot engine like it happened. I arrive in a week at the dacha, I need to cut a couple of logs, start the saw and at first the chain spins on a cool motor, then everything goes away, I stood for about 10 minutes, I start everything normally only on a cool motor. This is fine?
If the chain turns, then the speed is too high. It should be understood that a normally adjusted and serviceable motor is completely likely to have a slightly overestimated idling immediately after starting before warming up. And it can be decently elevated. before chain rotation. As the engine warms up, the idle speed gradually drops. For this reason, it is recommended to adjust the idle speed only on a warm engine.
Is it possible to put a clutch drum with a removable crown on a Stihl MS 180 chainsaw ("modernization" of the drum is allowed), for example, from the 250th.
Read also
Can. Everything fits perfectly. Just don't run over to 325". It's hard for the motor. But a couple of aspects should be kept in mind. 6: 7, respectively, the load on the engine will also increase. But practice has shown that this is not critical with normally sharpened chains. And secondly, a brand new chain of 50 links is difficult to put on such an asterisk. (In general, 51 links are recommended, but they happen occasionally). The first time you have to suffer so that she gets on the asterisk and the tire. And later, when she stretches a little, everything will be fine.
I bought a Stihl 180 chainsaw. I filled it with oil, benzyl. Started and gave to work without load at idle. I burned a tank of gasoline, at times I pressed a little on the gas. For some reason, the oil for lubricating the chain did not arrive, the oil hole remained dry. Or will it start to flow when the revs are higher and the chain spins longer?
How to start Calm 180 video
how to start calm, start chainsaws Stihl how true start chainsaw Stihl 180 1st video launch
Stihl ms 180 video
Wholesale and retail sales, service center, spare parts for products STIHL in Krasnoyarsk in the Trade and Service
At the 180th calm, oil is supplied to the chain when the drive sprocket is spinning (in short, when the chain is spinning), but it is not recommended to run in at idle.
On the MS 180 chainsaw, after using the 1st tank of fuel, I had more than half a tank of oil left. The ditch of the tire and the base of the chain, which is in the groove, are in oil. How to start a chainsaw calm, husqvarna, try to start the saw again. But when checking, for some reason the oil does not squirt from the chain and the cutting teeth, in my opinion, remain dry when sawing. Wood plaque appears on the upper part of the cutting tooth. Oil comes in, but comes out in the missing volume. Nothing could clog, the chainsaw is brand new, the hole is clean. Marriage of the manufacturer or as it should be?
I will not argue about the consumption of chain oil in calm weather, but 2-3 tanks of fuel per tank of oil is not much? I have less than a quarter of a tank of oil left after a tank of gas is used up.
When I start the tool with the chain brake off, it cuts in from time to time just when I pull the starter handle. Is it normal?
This model is quite peculiar in launch, there is no decompressor and / or elastostart that compensate for the recoil, and despite the small size of the piston, it is decent enough. Because of this, the saw must be started confidently smoothly by engaging the starter sharply and moderately pull the starter cord, it is worth at some point to loosen your grip or slow down the pulling speed, as the recoil will remind you of an unpleasant feeling.
What is the difference between the Stihl MS 180 chain saw with a 30 cm bar. and with a 35 cm tire? i.e. the distance from the spike to the tip of the bar?
So this value changes during use. The more the chain is stretched, the greater this distance. And the longer the bar, the greater the difference in cut lengths between the newest and the stretched chain can be. The difference in the length of the cut between the completely new and stretched chain will be about 1 cm in some places. The bar does not lengthen, but simply its tip moves further away from the saw body, otherwise the chain will not be stretched. The limit for the growth of the length of the cut is determined precisely by the length of the tensioner screw and in what place of this screw the tensioner cracker was when installing the new chain. The farther it was from the leading sprocket, the faster, other things being equal, the chain will become unusable due to excessive stretching. I am afraid that it is unlikely that it will be possible to purchase a tire that is 1 cm longer than the standard one. How to start a calm, start a chainsaw calm, how to start a chainsaw calm 180 the first start of the video. Regular tire lengths for consumer models. 12", 14", 16" and 18" for 3/8" x 1.3 mm chains and 13", 15" and 18" for 0.325" x 1.3 mm chains.
Is it possible to keep the brake off when starting, or must the brake be on?
And this is both more convenient and safer for you. There are three main launch options. on the Idling, at half throttle and at full throttle. In the first case, the chain is stationary after starting or may twitch a little. How to start a chainsaw The question of how to start a chainsaw can be divided into two parts: winding up according to the annotation what to do if the information from the first part does not work out will be useful to those. In the 2nd and 3rd cases. the chain is moving. Setting the brake to the working position in the first version of the start is a waste of time. It is very unlikely that the idle speed at one moment and without circumstances would increase so that the chain would begin to move. In the 2nd and 3rd cases, when starting with the brake activated, it is necessary to immediately release the brake after starting so as not to burn the clutch. When starting with the brake off, after starting, it is necessary to press and release the gas lever so that the saw engine switches to idle mode (in the 3rd case, this lever is already pressed at the time of starting, it only needs to be released).
It was necessary to work, the saw started up rapidly, although it stood idle for 5 months, sawing everything that was needed, burned one tank of fuel, everything is fine. But I arrive in a week, under it there was a puddle of oil before there was none. What could it be?
Never happened on these chainsaws. Usually breaks the oil hose from the attachment to the pump, if you throw cool oil in the tank and put the saw in heat. The breather only works inward, the pump does not let air through, so there is nowhere for the extra pressure to go, well, it squeezes out the hose.
I bought a chainsaw Stihl MS 180 C-BE. Started by annotation. The consumer should be aware not only of how to start the Stihl ms 180 chainsaw, but also of the technical specifications. Everything works fine, but very long and a lot of action. I tried to start without a brake in position I, and it also started up the first time. Tell me, is it possible to do this and what can it threaten?
It is better to start without a brake, the clutch will burn out quickly. Warm generally just starts.
Now my instrument is not working. I unscrewed the spark plug and it was wet. I put it on a gas burner, tried it again later. Doesn't start at all. I pulled out the candle 5 times, and it was always wet. What to do?
You try and not dry the candle. How to start a chainsaw video. I them, flooded. I usually start it like this: I unscrew the candle, turn off the ignition. Jerks 10. 15 starter (if very flooded, put the muffler down and pull). Later, I blow a candle on the candle to bring down the excess fuel and screw it in. But later I start not from the lowest position, but from the second from the bottom (the air damper is open and the “starting” gas is given). Usually a jerk from the third. the fourth starts. A bit of smoke and everything works. And from time to time it is too lazy to turn out the candle, so I give full throttle with my foot (on the ground, of course) and pull until it starts. In most cases it will work. And if, after blowing and drying the candles, you start again from the lower position, then fill it up again. there is already an excess of fuel, and we will also close the damper.
During operation, the stihl ms 180 c chainsaw did not idle and stalled. Started with difficulty, but stalled again at idle. After that, it won't start. The next day, after unsuccessful attempts to start, removed and washed the air filter. It did not help, I had to remove the candle. turned out to be dry, although attempts start there was plenty. I cleaned the breather with a needle (it was not clogged). I changed the fuel filter (although the old one is not visually dirty). I cleaned the carburetor and put in a brand new spark plug just in case. The saw won't start! Pulled out the spark plug again. dry. On chainsaws Stihl ms 180 as idling on a chainsaw. What to do?
Remove the muffler. Look at the piston, if it has longitudinal stripes, then a replacement is required.
I have been operating the Stihl 180 chainsaw for the 6th year, I took the newest one. Satisfied with the saw, apart from oil, filters and bearing grease, I didn’t touch anything, I did decent work over the years. This year I had to cut a lot, worked for three days. On the 2nd day, the saw began to trim, you seem to be gasping normally. On the 3rd day, the turnover fell by about 2/3. It runs at idle, it can stall from time to time, it does not start the first time. Yesterday put more did not touch. How to assemble a stihl ms 180 chainsaw after purchase. What could be?
Read also
I would take a look at the muffler. If it hasn’t been cleaned once in 6 years, it gets clogged and the exhaust gases have nowhere to go. Usually, with these symptoms, either the air filter is clogged, or the muffler.
Not so long ago I found out that better at times turn the tire on the chainsaw. for even wear. Tell me, is it worth it?
Spinning a tire isn't just better. certainly. With what frequency. depends on the amount of work. Not only twist, but also grind off burrs.
What is the difference between the drive and chain sprockets of the Stihl 180 chainsaw?
There is no difference between the "drive sprocket" and the "sprocket wheel", these are different names for the same part.
I bought this chainsaw, I really liked it, but I want to ask you if my saw can cut a thick tree?
Standard tire length. 35 cm, can be sawed log. 70 cm in diameter, if logs of such a diameter prevail, then you need a chainsaw with more power. The tool will, of course, cope with the task at hand, slowly and correctly cut all the logs of a huge diameter, but you need to keep in mind that by giving huge loads to an apparatus that is not designed for this, you (in the best case) reduce the life of the chainsaw, in other words, bring it closer to its full repair.
Can you please tell me if a 45 cm bar can be used on a Stihl 180 chain saw?
The chainsaw can be fitted with a bar with a maximum length of 40 cm.
Where is the breather in the Stihl ms 180 chainsaw?
Valve ventilation system("breather") is located "on top" of the gas tank and oil tank; everything is covered by the starter housing.
In the horizontal position, the gas button sticks. What to do?
Most likely, the lever-traction mechanism is faulty; when the unit is turned over, one of the levers or rods “sinks”.
Why is oil not supplied to lubricate the chainsaw tire? What is the problem?
The oil filter is clogged. The channel in the chainsaw body is clogged. The channel and the groove of the tire are clogged. Faulty oil pump drive (worm). Oil pump defective. The oil in the oil tank has run out.
What can you say about the overheating of the motor chainsaws Stihl 180?
I will try to explain about overheating of a serviceable chainsaw. I understand a working chainsaw as follows: the carburetor is correctly adjusted (it is enough to set the idle speed normally, by ear or by tachometer 2800), bearings, oil seals, filters, a candle. in order. The cooling system should also be in order, otherwise it happens that you can’t see what color the starter cover is, the grill is clogged, the air practically does not pass. If a serviceable chain saw will run on a conventional fuel mixture (high-quality gasoline with a fairly high octane number, not a bad two-stroke oil and its correct proportion). it is then that it cannot actually be overheated (sharp chain, of course). What could be the reason that saw Stihl ms 180 not. The reason for overheating is directly related to the fuel, you can overheat the newest saw in 5 minutes, while still working. Cause of overheating. not work or its duration, but fuel or oil. Or this and that. And with home, moderate use, subject to all of the above, this instrument never overheat.
Stihl 180 chainsaw: malfunctions and repairs, operating instructions The Stihl MS 180 chainsaw belongs to the class of portable devices. In this case, the engine has a 1400 watt model. Specifically, the volume of the engine is 31 cubic meters. see. At idle, the saw is capable of making more than 2 thousand revolutions. The chain of the model is provided for...