Installation of a curtain rod for Japanese curtains. How to sew Japanese curtains with your own hands

Fans of minimalism will surely be pleased with the fashionable trend - Japanese panels, or as we are more accustomed to call, japanese curtains.

Almost any curtain shop can offer a huge variety of these.

With their help, you can visually enlarge the space of the room and at the same time reliably protect it from the sun's rays. But if you are fond of sewing, you can try to make Japanese curtains with your own hands, and we will teach you how.

Japanese panels are primarily a stylish decor that can be used to decorate windows, doors and zoning the space of a room. Why panels? Because of their appearance. They are more similar to vertical blinds, only they can be moved in only one plane. These are strips of fabric from 0.4 m to 0.8 m wide, which are attached to the cornice. Special weights are attached to the bottom of the curtains, or, if the fabric is too light, a special frame (frame) is created.

Curtain panels can be of different shades, with different patterns, different different texture... The number of panels can be up to 10-12 pieces, which allows you to freely and quickly change the design to suit your mood.

Advantages of Japanese curtains

In addition to the excellent design project, Japanese curtains have a number of undeniable advantages:

Important. Japanese panels look quite impressive in combination with panoramic windows.

Which room to hang?

The beauty of Japanese curtains is that they go well with many interior designs. They will look best in the living room. Since this main room, you can try experimenting with translucent fabrics, bright colors, various textures and large drawings... It all depends on your wishes.

For the bedroom, it is worth choosing laconic, restrained colors. To give liveliness to the interior, you can add a panel with the image of flowers, birds or a graphic design. It is also advisable to limit the number of panels. Remember, in the bedroom, the simpler the better.

Japanese curtains will be a wonderful addition to the interior. The main thing here is to pay attention to the location kitchen stove in relation to the curtains.

If it is too close, it is better to use a cloth with a flame retardant. Of the flowers, it is better to choose those that are less susceptible to contamination, otherwise the amount of time spent on maintaining their purity will unpleasantly surprise you.

Which material should you choose?

Following classical traditions east, to create Japanese curtains it is better to give preference to natural fabrics such as silk, linen and cotton. Curtains look very beautiful, but at the same time unexpectedly and brightly, for the creation of which they used bamboo, rice paper or reeds.

If the budget is rather modest, but you really want Japanese curtains, you should choose colored plastic as the material. In addition, you will need a set of special strips that will act as a weighting agent for the curtains and prevent the appearance of folds.

! Important. The material of the panels is easy to change. In summer, you can use translucent fabrics, which will add lightness to the interior. In winter, you can give preference to heavy ones, dense fabrics- they will create a special atmosphere of coziness and comfort in the house.

Step-by-step instruction

As already noted, sewing Japanese curtains with your own hands is not difficult at all, and if desired, even a novice master can cope with this task. The main thing is to clearly follow the sewing algorithm.

Guided by this algorithm, you will be admiring pretty soon finished product decorating yours.

This accessory combines sophistication and severity, which allows them to successfully fit into almost any interior. japanese style look most impressive on large windows openings. They will successfully decorate a shop window, a niche, and can perform the function interior partitions and are successfully combined with curtains, curtains, they can be used in the format of curtains.

The fabric for Japanese curtains can be different: linen, cotton, shikatan, bamboo, silk, sutra. Materials of different textures and colors are often used for panels. The fabric is attached using a special curtain rod with several channels. For uniform movement of the canvases, the upper edge is fixed with Velcro adhesive tape, and the lower one is weighted with a special weight that is sewn into their bottom.

It is important to take into account the material of the profile, for example, plastic will reduce the noise level and reduce the distance between the tire and the top panel. When choosing a cornice, you need to take into account the following parameters: dimensions, number and type of brackets, height and side of the cord control, type of extension (from the center, one-sided). The panels can cover part of the wall or only the opening at the request of the owner.

The advantages of Japanese curtains

They take up little space in the space of the room.
The style of almost any interior will be successfully emphasized.
They are easy to care for.
They are universal in the style of the premises, rooms.
Multifunctional in terms of space zoning.

The Japanese curtain does not contain any assemblies, additional accessories (clamps, clamps), strict cut lines. This is what makes them so convenient and versatile.

How to sew Japanese curtains with your own hands

Everyone can make curtains in the Japanese style with their own hands. It will become a highlight of any interior and save money. After all, custom-made Japanese curtains are not cheap pleasure. Prices for a budget Chinese fabric alpha 2 m wide start at 500 rubles. A higher quality canvas (acacia, albion, apollo, alpha, intro) costs from 1000 to 3500 rubles. In addition, almost all firms require a separate fee for the departure of the measurer and installation of the cornice with panels.

Step-by-step instructions for sewing Japanese curtains: create panels yourself

Anyone who has basic skills in working with sewing machine... Cutting fabrics and sewing are simple, the main thing is to choose good fabric and make the correct measurements.

We cut the fabric into blanks 60 cm wide, taking into account the allowances (before that it is recommended to iron it with an iron).
Side ironing.
We trim the lower part of the panel with a rocker; we do not overstretch the side allowance. The width of the curtain should be a few millimeters larger than the weight.
We iron the cloth (to shrink the fabric). The master must see the upper edge of the curtain and precisely apply the Velcro with the front side to the allowance, attach it with pins, and sew. Then the fabric is laid with the right side facing you and the Velcro is folded to the wrong side and fastened with a stitch. The panel is carefully ironed.
We insert the weighting compound into the lower edge of the panel.
We attach the upper edge of the panel to the cornice.

The fabric must be ironed so that the panels are perfectly even. In the process of work, it is advisable to process all panels in stages to avoid oversights.

httpv: //youtu.be/Sh3buqBfJ34

Japanese curtains can perfectly complement any interior. An original simple cut, a variety of prints and fabrics make it possible to create this important detail living space with your own hands for little money.

Japanese curtains cannot be denied elegance and practicality, but their popularity is largely due to the functionality that the curtain rod provides for them. It is thanks to a special cornice that they can be hung over a window, door, wall niche or used as compartment doors and interior partitions, and alternating in different ways, differing in color and texture of the canvas, in a matter of minutes transform the appearance of a room. And if you decide to decorate your home with fabric panels, you will have to take care of choosing the right cornice for them.

What should be a Japanese cornice

The main design feature Japanese curtains lies in the fact that they are not gathered into folds, but are tightly pulled onto special frames or with the help of weighting slats. Thanks to this, they can be arranged in a line, one after the other, or interchanged without removing them from the cornice. Therefore, only multi-profile cornices are suitable for them, and the number of tracks on them depends on the number of canvases that make up the curtains.

So that the canvases can be freely moved and interchanged, each of them will need a separate guide track, but if such free movement is not planned, there may be fewer guides (at least one guide per two canvases). Runners with plates attached to them are inserted into the tracks, on which, in turn, the panels are attached.

The photo shows an example of an aluminum curtain rod with 5 guides and manual control

The photo shows an example of attaching curtains to runners using adhesive tape

Controls for Japanese cornices

There are three types of Japanese curtains on the cornice:

Independent manual. The fabric panels are moved along the window, holding them with your hands.
Dependent manual. To set the curtains in motion, you need to pull on a cord or chain. Moreover, all the canvases depend on each other and move either all together or in pairs.
Automatic. The cornice is equipped with an electric motor powered by a remote control or a switch.

If the window standard sizes double or triple curtains and a manually operated cornice. For wide windows or panoramic glazing, you will need curtains consisting of four or more panels, which are more convenient to control using an electric drive.

Electrically operated metal cornice mounted on the ceiling

When choosing between manual, rope and electric cornices, keep in mind: on a simple cornice, panels can be positioned and interchanged in any sequence, and on a cornice with a rope or automatic mechanism, only according to the same pre-set scheme.

Manufacturing materials

Most often, curtain rods for Japanese curtains are made of high quality plastic or metal (aluminum or steel). They are chosen based on the following recommendations:

Simple plastic curtain rods are the most common and sufficient cheap option, but they are only suitable for small windows and light curtains. Curtains with a lot of weight, he may not withstand.
For heavy curtains consisting of four or more curtains, better fit aluminum curtain rod that can support their weight and not bend.
If you plan to arrange panoramic glazing with Japanese curtains, it is recommended to choose a steel cornice with automatic control that can withstand heavy loads without loss operational properties and presentation.

DIY installation of the cornice

It is not necessary to invite professionals to install a curtain rod. You can cope with this task yourself. Since most of the curtain rods can optionally be fixed to both the wall and the ceiling, before installing them, you need to decide on the place of attachment.

For work you will need:

electric drill with hammer drill;
screwdriver or screwdriver;
fasteners (included with the cornice);
pencil and ruler.

Operating procedure:

Inspect the attachment point, step away from heating pipes, radiators or other heating elements... Please note that the curtains should fall freely without touching the windowsill and the battery. Make sure that there are no electrical wires passing through the drilling sites.
To set the curtain rod perfectly straight, use a pencil and ruler to mark it out. Pay attention to which side the window sashes open, and when marking, take into account the distance for their opening.
The distance between the fasteners should be 0.3 - 0.7 m.If a window or a future partition large sizes, the load on the cornice increases. Therefore, the step between the fasteners must be at least half a meter. On a small window, it is enough to fix the cornice in 3 places (along the edges and in the middle).
Drill the holes for the fasteners according to the markings. Install the cornice.
Tighten the fasteners. Press lightly on the bracket to check if it can handle the load.
Install the curtains and slide the lower weights into them. Check out the entire structure in action. Make sure all panels move smoothly and smoothly.

To fully use all the possibilities of Japanese curtains, you must choose the "correct" cornice

The basic principle of formation Japanese interior: only necessary and nothing superfluous, applies to curtain rods. They must be reliable, have simple form and not stand out against the background of walls or ceilings. Such a cornice will be a worthy addition to the screen panels and will make your life more comfortable.

Japanese curtains are several panels that are next to each other. This design is like a screen. If you want to know how to make Japanese curtains with your own hands: a sewing master class will help you figure it out.

Distinctive features

The standard width of Japanese panels is 60 cm. It is this size that the cornices are made for them:

No gathers along the top;
Various clamps, clamps and other accessories are not used;
Have strict lines.

Advantages

Japanese curtains have several advantages:

They are versatile;
Have no restrictions on the choice of textiles and colors;
Using natural fabrics, ecological cleanliness is ensured;
There are no folds on them, so dust does not collect;
They are easy to use;
An electrical mechanism can be installed on them;
Easy care;
You can assemble the structure and sew such curtains yourself.

Diversity

Today many people prefer modern interiors. Therefore, the use of Japanese curtains in recent times has become very popular due to the fact that such curtains organically fit into almost any design. Japanese curtains can be considered versatile. They are best suited for large windows. The main rule is that the curtains are combined with the interior of the room.

To provide more light in the room, the panels can be made transparent.
You can also try combining light panels with light pink or pale blue. However, in this case, the ornament should be discreet and small. If you want to reduce the light in the room, then opaque dark fabric is better.

Instructions

First you need to cut the panels:

To do this, measure the width of the window and divide it by 60 cm.Thus, we get required amount panels. If the width is divisible by 60, then the panels will be installed end-to-end. If the width is not short 60, then it should be rounded to big side and make the panels overlap;
Next, measure the length from the cornice, and add another 10 cm for allowances;
At the end, we multiply the resulting length by the number of canvases, which results in the total length of the required piece of fabric with a width of 60 cm. If the width of the web is 2 times larger, then the length is also reduced by 2 times;
Next, on a piece of canvas, we cut out the panels and process the sides and bottom of the canvas;
Panels need to be smoothed and finished with top. Upper bar, which will be attached to the cornice, has a Velcro, which is called velcro.

Now we start the sewing process:

It is necessary to smooth the Velcro;
The curtain is laid in such a way that you can see the upper edge;
Velcro is applied to the allowance with the front side and secured with pins;
Then they add everything;
The curtain is laid with the front part up and the velcro is folded to the seamy side;
All are fastened with pins and stitched;
Next, you need to iron the panel so that the panel is perfectly straight and even;
From below we make a drawstring and stretch a weighting agent in it;
Insert the upper edge into the holder.

Let's summarize

Japanese curtains can be used in many modern interior styles, the main thing is that they are combined and create a single composition. And by creating them with your own hands, you will get extraordinary and original design such panels, which will delight the eye and become a bright accent of the whole room.

Japanese curtains are a non-trivial element of the interior that came to Europe from the Land of the Rising Sun. Against the background of general interest in the original Japanese culture, such elegant curtains are increasingly used by interior designers to recreate the special, sophisticated and laconic atmosphere inherent in the dwellings of the inhabitants of the Far Eastern islands. The design of Japanese curtains is so simple that even a novice seamstress can make them with their own hands. In order to master the principle of making these textile panels, you just need to watch a small master class on sewing them and study the corresponding step-by-step instructions.

By outward appearance japanese curtains are like vertical blinds... Structurally, such curtains consist of separate rectangular textile panels, the width of which can vary in the range of 55-70 cm. Japanese curtains do not have draperies, their fabrics are attached in a taut form top to the rigid slats of the cornice holders, and at the bottom they are pulled back and straightened by the weighting slats.

Each panel is suspended with clamps or Velcro straps on its own rail installed in a separate groove of a special 4-7 row cornice. Such a device makes it possible, independently of one another, to move the screens across the entire width of the window, shuffle them, interchange them, or move them to the wall in the form of a single "pack".

Sewing instructions

Basic parameters of curtains:

the classic width of the panels is 0.6 m. It is this length that standard cornice holders are produced, designed for fastening such curtains;
panels of Japanese curtains, as a rule, cover not only the window, but also the entire wall on which it is located;
curtain screens are placed on the eaves end-to-end or with a slight overlap;
the height of the panels can be any, but usually they are made up to the floor length.

Measurements and calculation of fabric

Measure the width of the window opening or wall, divide it by 0.6 m and round the resulting fractional result upwards - this will be the required number of panels.
Measure the height of the room from the floor to the cornice, add 0.2 m to it for the hem of the upper and lower edges - this will be the length of the blank for one panel.
Multiply the length of the workpiece by the number of screens and thus find out the total length of the required material.
Taking into account the fact that the width of almost all modern fabrics is 1.4-1.5 m (which means that two identical blanks 0.6 m wide can be cut from one piece of material) divide the total length by 2 - this is and there will be the required footage. If the number of canvases is odd, round up the result.

Advice. When choosing fabric for Japanese curtains, give preference to natural or mixed curtain fabrics light color- monochromatic with an original, pronounced texture, or printed, with an elegant dull pattern in the form of stripes, bamboo or cherry branches, hieroglyphs or abstract geometric patterns.

Sewing panels of Japanese curtains

Iron the fabric with steam.
In strict accordance with the direction of the share thread, so that there are no distortions, cut the required number of blanks - rectangles of the estimated length and width of 0.65 m (5 cm will be needed to process the side edges of the panels).
Wrap the side edges of the panels twice on the wrong side - the width of the first hem should be 1 cm, and the second 1.5 cm.
Baste the hem, iron it, and sew 1 mm from the edge of the fold. Remove the basting and iron the side edges again.
On the lower parts of the panels, make drawstrings for threading the weighting strips. To do this, fold the bottom edge of each panel on the wrong side by a width of 1 cm. Press the fold, attach a prepared strip to the wrong side of the bottom of the panel, wrap it with a cloth and mark the desired drawstring width. Baste the drawstring, check again how the weighting agent enters into it, and if everything is done correctly, sew on the hem in the same way as described above. Pull out the threads of the basting, fasten the edges of the stitching, iron the drawstring.
If the rail-holders of your cornice are equipped with special clips, simply cut the upper edges of the panels to a width of 3.5-5 cm.

In the case when the straps assume the use of a special Velcro tape for fastening the fabric, in the common people called "Velcro", proceed as follows:

stick the hard part of the Velcro fastener (the one that has many tiny plastic hooks) on the cornice bar;
Iron the soft half of the tape, put it on the upper front part of the curtain (half overlapping its edge) and stitch it to the edge of the fabric;
Fold the Velcro to the inside of the curtain and stitch it to the fabric again, now laying the stitches along the second, free edge of the tape.
finally iron the panels, fix them on the cornice strips and insert weights into the lower drawers of the screens.

Advice. For sewing curtains, use a thin and transparent monofilament, then the seams on the fabric will be practically invisible.

Elegant Japanese curtains harmoniously fit into many modern interiors, therefore, with good reason, they can be called almost universal. Having sewed such unusual curtains with your own hands, you can equally well use them for decorating door and window openings, zoning the space of rooms and decorating terraces, verandas and closed gazebos.