How to set the time on alarms. How to configure and set the time on the StarLine A91 key fob? Detailed manual

In many devices, when replacing the power element (battery, accumulator), a complete data reset occurs. If the battery on the Starline A91 alarm key fob is replaced, the time is reset, after which it must be set again. But not everyone knows how to set the time, and this is required when using the timer function.

Modern car alarm system

Have been in use for many years modern systems car alarm. Once it was a luxury, but now it is convenience and safety. Car alarms are a 12 volt device. Has interactive authorization. Each alarm has its own encryption keys. They also have a function for remotely starting the car engine according to the time set on the timer or starting is carried out according to the temperature readings of the internal combustion engine (when the engine temperature drops below the specified one, the engine starts).
The interactive authorization function protects the car owner from hacking, which is carried out using an electronic reader. Resistant to the latest code grabbers thanks to conversational codes and a new frequency hopping method.
Methods of such protection, this method of data encryption are used in two control panels: the main and the additional. The StarLine A91 alarm device has good resistance to low temperatures. Works great in a temperature range from -45 to +85 degrees.

Functions that are capable of performing and are the same. The only differences are in the operating range, reliability, and ease of use.

Pros of StarLine A91

This alarm model is reliably protected from hacking, because it uses a new data encryption method. But, attackers are also constantly improving equipment for stealing alarm codes - .
There is a Megapolis mode. It should be used in densely populated areas where there is a lot of radio interference.
It is possible to start the engine in different ways.
The device is Russified.
Thanks to modern software, the response speed of the Starline A91 alarm is 20% greater than the speed of operation of the same devices, but previous models.

How to set up Starline A91 key fob

The remote control or remote control can perform several functions, namely:

Setting the current time on the device display.
Activation of the set alarm time.
The ability to turn it on and off.
Ability to set countdown timer.
The ability to activate the function of starting or shutting down the internal combustion engine.

How to set the time on Starline A91:

Press and hold button No. 3 on the key fob. The third button is used to change the time. You should hold this button until the following sound signals appear: one long melody - short beep - 2 short beeps. When the three sound modes have passed, the time display begins to flash. Button No. 1 should be used to increase the time, No. 2 to decrease it.
After the time has been set, you need to hold button No. 3 for a while to proceed to setting the minutes. As soon as the minute indicator starts flashing, we adjust the minute values using buttons No. 1 and No. 2.
Then, press button No. 3 again to set the alarm time. We also hold it until the alarm starts flashing and set the time with keys No. 1 and No. 2.
Next, you need to adjust the minutes of the alarm clock. Again, hold button No. 3 until the minute indicator blinks and also set the desired values.
Then, by briefly pressing button 3, the alarm clock turns on or off.
When you press the 3rd button further, the timer setting mode is activated. When the timer indicator blinks, set the desired value.
If you press button 3 again, you can also edit the minutes of the timer using buttons 1 and 2.
If you press the third button again, the timer will turn on or off. The first button turns off, the second turns on.

As you can see, there is nothing complicated in setting the alarm time. This applies not only to this model, but also to setting up key fobs different models car alarms.

Video

This video shows how to set the time on the Starline A91 alarm key fob

And in this video, in more detail, how to disable the Starline A91 alarm

And finally, the Starline autorun timer

Car alarms have a wide range of functions, including not only security systems. Not everyone can set the time on the Starline A93 key fob using buttons.

In addition to the standard engine shutdown, door, hood and gearbox locking, Starline car alarm owners have access to many secondary functions.

The system can turn on a timer for the turbine. After active driving on turbocharged engines, some elements of the intake tract heat up to about 800 degrees Celsius. Cooling occurs due to engine oil circulating through the system. Therefore, turning off the turbo engine immediately after aggressive driving is not recommended. Turning on the turbo timer is a useful function that depends on the watch.

You can set an alarm clock and auto-start on it. This setup will be one-time only. Setting an alarm clock is convenient if the owner is going to do unusual things after hours (pick someone up from the airport, meet someone from the train station). At the set hour, the Starline key fob will play the wake-up melody and then give a command for auto-warming. During daily use, you will need to constantly restart the system: go to the top menu (clock-alarm-clock-timer), and then set the alarm to activate again.

Instructions: how to set the clock on the Starline A93 key fob with 3 buttons

Some alarm key fobs have only three keys. You can set the time on your Starline device like this.

Press and hold button 3 until the sound signal sounds.
Then the clock indicators will flash. With keys 1 or 2 we can increase or decrease the value.
Then press button 3 of the Starline key fob again to switch to the minutes setting mode. Set the desired value.
You don't have to press anything to confirm the command. After five seconds, the menu will automatically exit, and the specified values will remain in the alarm memory.

Setting the clock with 4 buttons

The main Starline A93 alarm remote control has four keys. Therefore, the standard procedure for setting the time looks like this.

You should make sure that there is a battery inside the Starline alarm key fob and that the remote control is functioning properly and the keys are not blocked.
Press and hold button number four until one melodic signal sounds. Then two more short sounds will follow, indicating that the key fob has entered the time setting mode.
The value will now start blinking. You can set the appropriate number of hours using button two or three. The first key of the Starline key fob increases the value, the second one decreases it. After setting, press button four again, going into the minutes setting mode.
The procedure for setting minutes is carried out the same way– by holding down keys two or three on the Starline key fob.
The next press allows you to configure alarm functions or settings.
The Starline programming mode exits automatically after 8 seconds. You don’t have to press anything; the set time parameters will be saved automatically.

Reasons for settings failure

Sometimes the Starline A93 alarm system presents unpleasant surprises. Among the various “glitches”:

door unlock failure;
lack of command transmission from the Starline remote control;
Resetting time or autorun settings.

There are several reasons for the failure.

Car battery malfunction. If it is very discharged, it may not receive signals sent from the Starline tuning remote control. The machine's battery must be replaced for normal operation.
Wiring short circuit. If the Starline A93 car alarm is connected incorrectly, problems may arise. Another reason is a broken or frayed wire on the road, which can cause a short circuit. To eliminate the problem, you will need the help of a car electrician at a specialized service.
The reason may be the Starline keychain itself. You should inspect it for mechanical damage - there should be no breaks or chips in the plastic, cracked screen or other defects.
Dead battery. The signal, as well as the time setting, may be lost due to a faulty battery in the Starline setting key fob. It is necessary to open the compartment and inspect it. The battery should not be swollen, and the remote control contacts should not have traces of oxides or rust. Otherwise, you need to install a new battery and clean the contacts. To prevent such situations, it is advisable to change the battery in advance - approximately every 3-4 months. You should install nutritional elements from trusted brands.

If a malfunction occurs, glitches appear or the time is reset, it is advisable to reset the Starline alarm parameters to factory settings. To do this, you need to know the location of the Valet service button, which is installed when installing a car alarm.

It allows you to enter Starline programming mode, start the car without a key fob, etc. That’s why they hide it. If you do not know the exact location of the service button, you should check these locations:

under dashboard;
on side maps;
behind the decorative covers of the center console;
under the sun visor.

Once the button is found, you can begin resetting Starline to factory settings.

Turn off the ignition.
Press the service key 9 times to reset the first programming table.
Turn on the ignition. The vehicle will emit nine beeps and lights to indicate that it has entered the appropriate mode.
To completely reset it, you should carry out the procedure twice - the second time you need ten clicks on the button to reset the second table.
After finishing, you need to press the service key, and then listen to one siren signal.
Click K1 on the Starline key fob. The machine will beep to indicate a return to standard settings.
Turn off the ignition. The car will flash the emergency lights three times, indicating the successful completion of the procedure.

Setup video

How to configure and set the time on the StarLine A91 key fob? Detailed manual

Quite often, after replacing the batteries in the control panel, owners do not know how to configure and set the time on the StarLine A91 key fob. Especially for owners of such devices, we will briefly talk about this, so that many who encounter such a problem can independently set the current time on the display. It is important to perform this operation correctly, since many owners use a timer to start the engine.

Configure and set the time on the StarLine A91 key fob possible for any driver, regardless of driving experience. The development of this model of car security alarm fully meets the requirements of car owners to ensure their safety. Therefore, the key to ensuring the correct and long-term use of such a system is to study the instructions for its operation.

A few words about the security system

These developments of security systems are among the most modern and reliable 12 Volt devices, have interactive authorization, encryption keys are individual for each product, and have a function such as remote start at a set time on the control panel timer or engine temperature. Performance is maintained even in conditions of strong radio interference in urban areas.

The use of interactive authorization eliminated the possibility of intelligent electronic hacking and provides high resistance to all code grabbers known today. This became possible after the use of conversational encoding algorithms, using individual encryption keys, as well as a new, previously unused frequency hopping method.

This encryption method is used for both control panels, both for the main key fob and for the additional one. The existing system fits well with machines that also have such a button. The device has good resistance to changes in outside air temperatures. High performance is maintained at temperatures from minus 45 degrees to plus 85 degrees.

Benefits of using it

- The product is highly resistant to hacking attempts, thanks to the use of new encryption methods;

- The presence of the Megapolis mode allows the use of products in places with big amount radio interference;

- You can use several in different ways remote engine start;

- All inscriptions and pictograms are made in Russian;

The use of modern software developments has made it possible to achieve an increase in the speed of operation of devices by approximately 20% compared to other models of similar devices.

The appearance of the StarLine alarm system in the automotive markets was a real discovery: an excellent combination of innovative functions, a high level of protection and an intuitive interface made the system a leader among security systems. Why does a car alarm deserve such high ratings, how does it differ from its analogues, and how to set up a Starline key fob.

Features of the Starline alarm system

The conversational method of data encryption is one of the main features of the Starline car alarm, which reduces the risk of car hacking. All models of the system, designed for use in urban environments, have a large range of up to one and a half thousand kilometers. Signaling resistance to radio interference is ensured by separate channels to which radio interference is sent.

A distinctive feature of the Starline alarm system is self-diagnosis - the system automatically checks and controls the operation of all sensors in the car. The alarm key fob or the unit's LED indicator notifies the driver of damage to the system or any of its elements. Any Starline alarm model is equipped with an instruction manual, which contains information about what type of protection is provided in a particular complex.

Car alarms are equipped with various security mechanisms that prevent hacking attempts:

Interception of the system signal is impossible using dynamic code;
The alarm signal can be interrupted without removing the protection from the vehicle;
The alarm signal is cyclical, but the number of its repetitions is limited;
In the event of a power failure, all car alarm settings are saved;
You can turn off the alarm urgently by entering a personal access code.

Thanks to its compact and ergonomic shape, the keychain fits comfortably in the palm of your hand. The interface is entirely in Russian, which simplifies working with the system. The absence of an antenna on the key fobs simplifies their operation.

System capabilities

When choosing a security system, car enthusiasts pay attention first of all to its functionality and capabilities. Depending on the specific alarm model, the set of options and the number of protected zones may vary, each of which has an individual protection algorithm.

Starline alarm functionality includes:

Engine control and blocking in the event of an unauthorized attempt to start are carried out by relays - digital or conventional.
Remote ignition.
Protection of doors, hood and trunk is guaranteed by limit push-button switches.
The windows and body of the car are protected from impacts by two-level sensors.
The condition of the car interior is monitored by a sensor installed inside it.
Inability to release the parking brake.

The instructions included with the car alarm state that the system is capable of not only protecting the car, but also notifying the owner in the event of a break-in or attempt. Alerts can be very different:

Transmitting a signal to a key fob with feedback;
Sound and light warning;
Possibility of engine blocking;
Panic mode;
Safe engine blocking mode that simulates engine failure.

Remote starting and operation of the car engine are controlled by the car alarm processor. The system functions can be performed either automatically or manually using the key fob.

Principle of operation

StarLine alarm systems are equipped with special technology that operates through a secure channel. After the security system receives a signal from the sensor, it checks its authenticity. The response request for confirmation is sent in the form of encoded numbers.

A certain algorithm and secret code allow the car alarm key fob to process the received signal and send a response to the control unit. The alarm will turn off if the sent and received signals match, and a confirmation is received on the key fob. The entire process of signal exchange takes no more than a few seconds.

Instructions for use

The security system comes with an instruction manual, which not only explains the principle of its operation and method of use, but also the installation process. Accordingly, installation, configuration and operation of a car alarm can be carried out by the car owner independently, without contacting service centers and auto repair shops.

Do-it-yourself Starline car alarm connection

Installation process security system requires a set of tools:

Wrenches;
Soldering iron;
Nippers;
Electric drill;
Screwdriver;
Heat-shrinkable caps;
Tester - they will check the electrical wiring.

Step-by-step installation process

Before you begin installing a car alarm, you need to turn off the power to the car - disconnect the battery terminals. You can consider the installation process using the example of a Chevrolet Lanos.

The instrument panel is removed. To do this, the dashboard is disassembled: the climate control and headlight control units, the lining under the “small” glove compartment and the radio are removed.
Location of climate control and headlight control units Location of the screws on which the headlight control unit cover is attached Location of the lining fasteners with right side
Location of mounts above the dashboard Location of climate control unit mounts
The instrument panel itself is removed. It is attached using three connectors.
The main car alarm connections will be made on the dashboard connectors.
The linings of the torpedo and steering wheel are removed: the first is fastened with two screws on the side of the steering wheel, two self-tapping screws and one screw from the bottom, the second - with four screws.
A power connector with six contacts is connected to the ignition switch.
The cover is removed from the fuse block, and the bolts that secure the fuse block itself are unscrewed.
A wiring harness protrudes from the driver's door and is located behind the fuse box. The central locking is connected to it.
The LED lamp and signal transmission and reception unit are installed inside the car.
The engine compartment contains a siren, a temperature sensor and a hood switch. The trunk limit switch is mounted in the trunk.
All removed elements the interior linings are returned to their place.

The locations of the system parts are determined in advance. The most reliable places for the control unit are the front seats or the space behind the instrument panel. The siren is mounted in a place protected from moisture - the space next to the engine is optimal. They try to position the antenna in such a way that it does not come into contact with the metal and wiring of the car.

A shock sensor is mounted in the central part of the cabin. This arrangement is chosen due to the fact that it must read the impact at the same distance from all sides.

An LED is attached to the center console. Such a prominent location alerts potential car thieves that the vehicle is protected.

All elements are connected only when protected mode is enabled. After all parts are placed and the system is configured, grounding and power are applied. Installed alarm tested for correct installation and functionality.

During the test, the car alarm may go off falsely. The reason for this is the high sensitivity of the installed sensors - to eliminate such a reaction it is necessary to recalibrate them.

Video: installing a StarLine alarm on a car

Immobilizer bypasser

An immobilizer is one of the anti-theft devices that blocks the operation of the engine and some other components in the event of an unauthorized attempt to enter and start the engine. Similar devices are characterized by increased efficiency, which insurance companies take advantage of: agencies agree to enter into contracts with car owners only if the vehicle is equipped with such equipment.

It is impossible to visually determine whether there is such a device in the car or not - it does not produce sound or light signals. The main task of the device is to prevent the thief from starting the car. Even if the device is detected and subsequently destroyed, all components and elements of the machine will remain blocked, which often becomes a problem for the vehicle owner.

When installing an alarm system, you can bypass the immobilizer. There are several ways to do this, but one of the most popular is to use a crawler - a module that allows you to overcome the effect of the immobilizer. Such devices are created and sold by the same companies that produce security systems, related equipment and their installation.

The bypass module, or immobilizer bypass, is a compact device, inside and outside of which there are transceiver antennas. The device body also contains a chip or key. Both antennas are designed to receive and transmit a signal when starting a vehicle engine using an alarm key fob. The crawler only works when the car is started from the alarm key fob and does not respond to the use of the key.

An immobilizer bypass specialist should be selected. The main difficulty in this process is the selection of a module that matches a specific car model: on many of them, the signal supplied by the immobilizer is too weak, which is why it has to be amplified first.

Bypass modules are developed specifically for specific models of alarm systems. For example, a StarLine BP-03 crawler was created for the StarLine A91 Dialog system - it is this device that is synchronized with this car alarm model.

Setting up a car alarm

The first step after installing a security system is to correct setting. You should start by linking it to the key fob system.

Key fob binding

The Starline car alarm keychain cannot be worn with metal keys. A similar taboo applies to any other security systems.

The car alarm is equipped with two remote controls. The main one has a liquid crystal display and four control keys. The additional one does not have a display, it is equipped with only three buttons and a light indicator. Before using the key fob, perform basic system settings:

Set the date and time;
Set an alarm clock - if the car owner needs it;
Set a timer;
Adjust the volume of emitted signals;
Select the beep tone.

Priority in system control is always given to the main key fob. In fact, it is the only remote control from which remote control security complex. An additional key fob can only be used as a duplicate if the main one fails. Car alarm settings using the key fob buttons are carried out as follows:

Several quick presses, each lasting no more than half a second;
Press and hold the key until a beep sounds;
Double clicking the buttons;
Consecutive pressing of several keys.

The variations of actions with the key fob listed above are necessary for activation and deactivation certain functions Starline systems.

Cursor setting

Some of the modes supported by the car alarm are programmed using the cursor method. The user manual indicates the function keys with which the settings are carried out. Activation of the cursor method occurs by two keystrokes - one lasts until a sound signal appears, the second - quick - confirms activation. As a result, the icon corresponding to the enabled function should appear on the liquid crystal display of the main key fob. Control buttons allow you to move from one character to another by selecting the desired function. Activation of the selected option is carried out by pressing other keys - their numbers are listed in the operating instructions.

Using the cursor method, you can activate and deactivate almost all functions of the Starline alarm system:

Door locking and unlocking function;
Anti-robbery function;
Silent protection mode;
Third party service mode;
Turning the turbo timer on and off and many others.

Alarm Modes

The Starline security complex has a wide functionality and a set of programmable modes:

Anti-robbery;
Alarm immobilizer;
Self-diagnosis of the system and sensors;
Panic mode;
Silent mode both with the engine running and with the engine turned off;
Automatic start of the security system in case of its shutdown;
Silent operation of sensors in response to impacts on glass, body and wheels;
GPS monitoring and determination of vehicle coordinates;
VALET mode - emergency call for help;
Independent programming of a new key fob in case of loss of the old one with the destruction of the old encryption code;
Automatic wheel blocking in case of evacuation of the car by special equipment.

How to program them?

Activating the keys on the main alarm key fob allows you to control all modes stored in the system memory. Changing certain parameters, adjusting and selecting modes are accompanied by sound and visual signals: icons appear or disappear on the display.

To program the modes, you must press a certain combination of keys on the alarm key fob. It matters not only correct sequence button presses, but also the duration of their holding.

Several examples of programming car alarm modes:

Consecutive pressing of the first and second keys activates the silent security mode;
Similar pressing of the first and third keys starts the car engine;
Pressing the second and first keys with a break of a second starts the vehicle security with the engine running;
Consecutive pressing of the second and third keys turns off the engine;
The key fob buttons are unlocked by simultaneously pressing the second and third keys;
The key fob button locking is activated by simultaneously pressing the first and third keys;
The “panic” mode is activated when the first and second buttons are pressed simultaneously and the engine is turned off. With the engine running, a similar action will trigger the anti-robbery mode.

Meaning of key fob keys and pictograms

Button 1

A single press activates the sound security mode, a long press activates the silent mode;
Double-clicking activates and deactivates the shock sensor;
A single click locks the car doors while the engine is running.

Button 2

One press deactivates the security mode with sound. Pressing it again deactivates a similar silent mode;
Single press opens door locks with the engine running;
Double single click activates anti-robbery mode;
A single press turns off the alarm.

Button 3

One keystroke controls the system status;
Double clicking turns on search mode;
Pressing a key on the key fob with a display starts the cursor programming mode. It includes various functions- temperature or time start, timer start, immobilizer and turbo timer activation, service maintenance.

How to configure system autostart

The auto-start function of the security system is configured by the technician who installed the alarm using a personal PIN code entered into the modular control unit. When the security system is first started, all factory settings and changes made to them are saved in the memory of the security system.

Internal failures and malfunctions of the system are extremely rare, but if this happens, they are eliminated by resetting all settings to factory settings. This can be done by pressing the VALET service key or entering a secret code.

Video: setting up the StarLine alarm

Sensitivity adjustment

The Starline system installs a two-level sensor, the operating principle of which is based on the piezoelectric effect: before the car body is hit, it picks up a sound wave. Such sensitivity is guaranteed only by rigidly mounting the sensor on metal surface associated with the body. To adjust the sensitivity, you need to increase the warning zones and decrease the other two. Then the security mode is turned on, and after 40 seconds a light blow to the body is performed.

The level of sensitivity is checked in a similar way: it is reduced if the reaction is too acute. The full alarm zone is debugged in a similar way. For warning and alarm indicators of the shock sensor, the maximum sensitivity value is 14, the minimum is 0.1. A zero value, of course, completely disables the sensor.

Reducing sensitivity level

The car's service book indicates the location of the alarm control unit only if the car has a standard security system installed. Otherwise, you will have to focus on the VALET key: the wiring goes to the control unit from it. It is usually located near the pedal assembly. Sensitivity is reduced by adjusting the control element responsible for this function. The indicator should not exceed the average values and not be below 4–5 units.

Setting incorrect sensitivity values can cause malfunctions of the warning system, due to which it will not be able to transmit signals about serious damage to the wheels and body of the car. The location of the antenna module also affects the sensitivity level. Installing an antenna on the windshield reduces to zero the likelihood of the security system being activated in the event of an impact on the rear of the body or the wheels. You can change the alarm parameters and adjust the sensitivity by simply moving the module to another location and then checking it.

Starline car alarm malfunctions

The following breakdowns can be considered common malfunctions of Starline car alarms:

Discharging the key fob. The battery installed in the remote control does not have a long service life, so at the first sign of incorrect operation of the system, it is worth checking and replacing the battery if necessary;
Power problems - low car battery, problems with the fuse box or the power system of the alarm itself;
Damage to the central control unit. Such problems can lead to complete failure of the entire system;
Sensor malfunctions. Individual alarm elements can always be replaced with new ones.

Most problems can be solved by replacing the failed part with a new one. The most complex is the control unit - its repair and replacement cost a large sum, since key fobs and some other alarm components must be replaced along with it. Such work should only be entrusted to the professionals who installed the security system.

If the key fob does not respond

The lack of response of the key fob to key presses is not always a symptom of a serious breakdown. In most cases, the cause of this malfunction is a dead battery. If after replacing the battery no changes occur and the key fob does not come to life, then you should look for other reasons for problems in its operation:

There are high voltage lines or a powerful radio station - they can jam the signal coming from the key fob;
The car battery is dead;
The key fob is not within the alarm range.

In the situations listed above, it is enough to drive the car and check the key fob again. Absence positive result may require disassembling the system control panel.

The key fob body is disassembled. It is necessary to look for cracks, traces of poor-quality soldering and other damage in the insides;
Using a soft brush, be sure to remove debris, dust, and hair. You cannot wipe microcircuits with liquids - they may fail;
The loose parts are carefully soldered back into place;
All wires, conductors and other parts are checked with a multimeter.

If you have fully checked and disassembled the key fob and it does not begin to respond to key presses, then you should pay attention to the tuning capacitor. It is turned 10 degrees with a screwdriver in programming mode and with the button pressed. The procedure is repeated until the system and key fob are synchronized.

Video: StarLine alarm key fob repair

Advantages and disadvantages of Starline car alarms

The main advantage of the StarLine car security system is its ease of installation: a clear presentation of all installation stages in the operating instructions allows the vehicle owner to independently carry out all the necessary actions.

The advantages of the Starline alarm system include:

Possibility of installation on any car, regardless of the type of transmission and engine.
Resistance to temperature changes and atmospheric influences.
The strength of the key fob body.
Protection from third-party signals and interference.
Autostart function, which increases the efficiency and comfort of using the system.

At a relatively low cost, car alarms not only have standard set function, but also additional options. Wide the lineup allows car enthusiasts to choose the most suitable system for their car. The Starline alarm functionality may vary depending on the model and include different options:

Vehicle location tracking via satellite communications;
Automatic engine start;
Various ways to notify the driver in emergency situations;
A large number of channels to eliminate radio interference and many others.

The only disadvantages can be considered a large number of electronic components, the breakdown of which may require replacement of the entire alarm system. However, you can always avoid such consequences - it is enough to monitor the condition of not only the security system, but also the car.

The StarLine car alarm system can be called an ideal security system capable of protecting a car of any price category. Easy to install, wide functionality, additional options, intuitive interface, high level protection - all this is worth equipping your personal iron horse with such protection.

Setting the time on the key fob is necessary for a reason: the alarm system has the ability to automatically start the engine using a timer. You will be able to go out to an already warmed-up car all work week without making any effort - and park the car so that it has a stable connection with it.

The site employs an auto electrician-diagnostician, a certified StarLine specialist. If you have questions about car alarms, ask them at the end of the article in the comments or on Vkontakte.

Setting the clock

To enter the configuration mode for the key fob itself, press and hold button 4: first the key fob will give one signal, after a pause – 2 more. After that, release the button. The hour display will start blinking - set the desired hour by increasing the number with button 2 or decreasing with button 3. Then briefly press 4 - the minutes will start blinking, set them in the same way.

By pressing 4 again, you will go to setting the alarm time - set the hours, then the minutes in the same way. The next press on 4 will switch the key fob into the alarm on/off mode: if you set it to ON, the key fob will sound an alarm every day at the previously set time. Select the desired setting and press 4 again - now set the autorun timer.

The principle of setting the autorun time does not change - set the hour and minute, press 4 and then turn on the timer (ON) or disable autorun by timer (OFF).

You can also activate the timer launch in the second way, and there will be some differences in the operating algorithm:

Press and hold button 2 or 3 until you hear a long beep followed by a short beep.
The alarm clock icon will start blinking on the screen in the bottom row. If you press button 1, it will light up constantly, buttons 2 and 3 will switch to the adjacent icon.
To exit this mode, hold button 1 for a long time until the signal sounds.

What is the difference? If the alarm icon is displayed on the screen, then autostart will not occur at the time set by the timer, but at the time for which the alarm is set. If you activate the icon “ hourglass", then it will occur starting from the time you activate this mode and then every few hours. What is it for? In cold weather, this mode of operation allows the car not to get cold, and it is used on diesel cars, or when spending the night in the car in winter. To set up periodic autorun, you need to activate the hourglass and set the key fob timer and set the correct interval.

As soon as you activate the hourglass, the display on the screen will change: initially the inscription 4H will appear, and further short presses on button 1 will change the inscription to 6H, 8H and so on up to 24H. Periodic engine starts will occur at intervals of 4 hours, 8 hours, and so on. When you exit setup mode, the engine will start automatically.