Making concrete blocks at home. Self-making blocks: instructions and advice

This article is intended for those interested in the maximum reduction of building materials. From it, you will learn about the way of making a slag block with your own hands using a vibrostanka. We will tell about how to independently create a matrix for blocks and on the rules for the manufacture of blocks for walls.

Slagoblock is the easiest and most affordable stone Materials For walls. Its history has more than 100 years, and the combination of the properties of a constructive and insulation makes it indispensable today.

Mass private construction on the periphery, especially in utility and farms, requires constant reduction in the cost of building non-residential premises. For the walls of Sarai, Khlev and Storage Rooms, it is hardly not all that comes on hand - from the naked to Mergel. In this article, we will consider the possibility of creating a vibrostank for the manufacture of slag blocks.

Note. For the manufacture of the machine you will need the skills of the welder and locksmith.

Appointment of homemade slagoblok.

Should immediately make a reservation that final product It will not have high strength and durability compared to factory "prototypes". Home production does not allow to withstand the technology, since there is no possibility for a steaming procedure in which the material is saturated with the necessary moisture and gets optimum temperature For the binder reaction (cement). However, blocks are quite suitable for the construction of lungs. one-storey buildings With service life of about 30 years.

Machine for slagoblok.

Main detail homemade machine Is a matrix or a form for a raw material mixture. In essence, it is a steel box with elements installed in it in the form of voids or without them. The matrix itself is already a machine that can be used by performing part of manual operations.

For the manufacture of the machine will need:

Welding machine.
Bulgarian.
Vice.
Flooring tool.

Materials:

Steel sheet 3 mm - 1 square. m.
Pipe Ø 75-90 mm - 1 m.
3 mm band - 0.3 m.
Electric motor 500-750 W.
Bolts, nuts.

Operating procedure:

Remove dimensions from a standard slag block (W / B) or determine the necessary dimensions.
Cut from the sides of the sides of the matrix from the calculation by 2 W / w with a partition in the middle. There should be a box with two equal compartments.
Voids must leave the bottom wall with a thickness of at least 30 mm. From this calculation, we determine the height of the cylinder (or parallelepiped) to limit the voids.
Cut 6 pipe segments with a length of equal to the cylinder height.
To give the cylinders of the cone shape, it is necessary to cut through each of them along the middle, enhance the vice and connect with welding. Diameter decrease by 2-3 mm.
Raw cylinders on both sides.
Connect cylinders with each other in the form of a row along the long side of the block. They must copy the location (step, diameter) of emptiness on the factory sample. Along the edges, add 30 mm plate with a hole for fastening to the briefs.
In the middle of each of the compartments of the matrix make feeds and trust the eyes with back side box. It is necessary for the possibility of temporary fastening of emptiness limiters. So you will get the opportunity to remove them, produce monolithic blocks.
On one of the transverse walls (outside), navar 4 bolts under the fastening holes of the vibromotor.
Spice apron and blades on the edges from the load side.
Clean and polish all the details under painting.
Make a press in the form of the body of the block material - a plate with holes, a diameter of more cylinders by 3-5 mm. The plate should freely enter a depth of 50-70 mm in the box where limiters are installed.
To the press to privar comfortable handles.
To paint the entire design of the primer and install the vibromotor.

Video Type of Mold Production for Slag Block, Part 1

Video Type of Mold Production for Slag Block, Part 2

To convert the conventional electric motor to the vibromotor, it will only be necessary to add to its shafts eccentric in the form of welded bolts. Their axes must coincide. You can screw the nuts on the bolts by selecting the desired amplitude and the frequency of vibration. More information you will find in our article "Vibrotol with your own hands."

Such a matrix can be the basis for a stationary or walking machine. For its modernization, a developed mechanic skill and more accurate execution will be needed. Variants of machines Multiple and the main factor is the presence of a girlish material (metal).

Vibrostanok for slagoblock, video

Material for homemade blocks

Theoretically, the "home" blocks can be made from anything - clay, opilk concrete, ceramzite concrete, etc. The optimal composition of the mixture is 1 part of the sand, 1 part of the cement, 3 parts of the grams.

The crucial moment is the humidity of the mixture that is easy to determine "on the eye". Previous mix Must keep the shape of a lump and not to crumble. These consistency raw materials can be laid in the matrix and press blocks from it. Instead of emptiness you can use glass bottles, Brick fight or acute stone.

How does a factory machine for a slag block - video with explanations

Work with homemade machine

Before the first boot, lubricate all the contact planes with oil - the solution is smaller than the metal. The vibrator can be included at any stage, but most effective to do it before pressing. Take care of the reliable electrical insulation of the motor. The apron should close it from the mixture.

Ready blocks should be kept on open air In summer weather (from +10 to +30 ° C) for 3 days. Field S. finished products It is necessary to cover with polyethylene to avoid early peas.

SAMI simple form For blocks. Video process of work

Perhaps such a machine will not become a source of reliable and almost free material for the construction of a residential building, but will help to significantly save on the content of the farm or the construction of the garage. Applying a masonry solution for plastering walls (1 part of cement, 3 pieces of sand), you will extend the life of the handling slag block at least 1.5 times.

The slagoblock refers to very popular materials from which buildings of any type are erected. The technology of manufacturing a slag block at home is a vibrating pressing of a certain mixture in special forms.

The production technology itself and the composition of slag blocks provide that in blocks use special devices and machines that can be made with their own hands. The dimensions of the standard block are 39x29x19 centimeters, inside the presence of three identical holes.

The advantages of slag concrete blocks

The composition of the slagoblock (however, like foam block) is truly unique:

Slag concrete blocks have excellent heat and sound insulation.
Such blocks have sufficient fortress and durability.
Good cement savings. So, for cooking 36 pieces will go one bag of cement.
The current Russian legislation does not provide compulsory certification of the same slag concrete material, nor equipment with which it is produced. That is, there is no need for mandatory security check and quality.

Hence the conclusion: it is the slagoblock that is the most profitable material for construction on its site, because in this case the process is fast, economical and reliable.

Cooking solution for slag concrete

Before talking about how to make slag blocks at home, consider the preparation of the solution for them. The composition of the solution for slag concrete blocks includes a filler, better if it is a slag that remains after combustion of coal in the furnace, in an amount equal to seven bulk parts.

Large clay sand is two parts, gravel, fraction 0.5 - 1.5 cm - two parts, cement, M500 brand - one and a half and water - three volume parts. But the filler may not only be slag, as such it is possible to use gypsum, crumples, ash, gravel, chopnque, sand, brick waste and even treated sawdust.

ATTENTION: The proportional composition of the water is approximately, and in the process of kneading the solution, it is necessary to control its delicate. To check it is enough to take a lump of a solution and throw on the ground. The high-quality solution crushes, and the compressed in the fist will stick.

When using domain slags, like filler, no extra additives should be present: sinters, land or not burned coal. Therefore, the slag must be sorted in advance, is soles with a special sieve.

If the filler serves as a gypsum, then the components of the slag concrete are taken in the following proportions: the gypsum is one piece, the slag mixture is three parts and water. The solution is thoroughly mixed, and is used almost immediately.

Such a mixture is prepared for a maximum of six minutes. Pre-slag mixture is moistened. For the preparation of one cubic meter of solution, about 350 liters of water are used.

In order to make a special plasticizer in the home at home, a special plasticizer is added to the solution. As a result, the mixture becomes very plastic, and the blocks are obtained by durable, waterproof, frost-resistant and not fragile.

In addition to hollow, blocks can be made and full. They are the most stronger and durable, and most often of them make the foundation. Unlike them, hollow blocks have ease, excellent insulating and soundproof properties.

Well, another important property: slag blocks can be color, if you add dyes into a solution that the chalk or crushed red bricks can serve.

Articles on the topic:

Methods for making slag concrete blocks

Currently, such a question is how to make a slag block at home, you can solve in two ways:

In the first way, small forms are used in which the blocks are solidified;
When the second is used special equipment. This equipment may be factory manufacture or made independently, possibly with the involvement of a familiar Tokary.

Slag blocks in forms

The manufacture of the slag block at home is possible with both wooden and metal forms. It's believed that standard dimensions The block is 39x19x19 centimeters, but depending on the purpose of the form you can do in virtually any.

Forms consist of lateral walls and bottom. If the forms are made in such a way that in each pouring to several blocks, you can significantly save the material.

ATTENTION: When using such forms, the solution should be homogeneous and sufficient dense to fill these forms without forming voids.

So that the blocks obtained light and inexpensive, empties are created in them, for this, glass bottles are inserted into the forms. To make them easier to get them, they are located in the neck. The excess solution is removed, the remaining is well recomposed.

In forms, blocks are located during the day, then they are pulled out and stored by low stacks. For construction, they are ready in a month.

Slag concrete on special equipment

Production of slag blocks at home in this way, is more high-performance and guaranteing more high quality. But for this it is necessary for special equipment, in particular concrete mixer and vibrationtol.

For the manufacture of the machine you need:

using a steel sheet, thick 2-3 mm;
asynchronous engine whose power 100 watts and more;
cargoes to call imbalance and vibration;
cylinders to create emptiness.

We make the machine for the production of slag concrete blocks

Equipment for slag blocks at home can be made as follows:

Billets cut from steel sheet next Size: Two rectangles 40x25, two - 20x25, one - 40x15, four - 4x4 and one - 39,5x19.5 centimeters.
From steel rectangles 40x25 and 20x25 centimeters, the shape is welded, the internal dimensions of which will correspond to the size of the standard block. But, as already mentioned, the dimensions can be varied.

ATTENTION: To clearly comply with the size of the blocks and maintain the quality of the ribs, the weld must be located outside.

Three blanks are cut from the pipe, with a diameter of 8 centimeters, 25 cm long.
These billets are welded to the form, with the help of rigidity, 4x4 cm in size, while they are located in its upper part.
The vibrator is attached to a longer side of the form, used for this bolts with nuts. The bolts themselves are grabbed by welding.
To protect the engine from water and a solution, a visor is welded above it, an additional leg is welded to the edge. It is necessary for additional sustainability, because due to the vibrator, the center of gravity of the entire design has shifted.
Clamps are welded to the handles and you can start making slag blocks.

For the manufacture of homemade blocks, only a few forms are required for their castings, as well as cement, sand and filler - slag or broken brick. Other types of fillers (gravel or crushed stone) will make a block very heavy, and in addition, a wall, folded from such a material, in the summer will heat up faster, and in the winter cool. If you use clamzite as a filler, then, although it has almost the same thermal insulation properties with a broken brick and slag, it will cost several times more expensive.

Forms for the manufacture of building concrete blocks

For independent manufacture of building blocks at home, special metal or wooden forms will be needed, the internal dimensions of which are different: 150 x 150 x 300 mm, 175 x 175 x 350 mm or 200 x 200 x 400 mm. With minor blocks it is more convenient to carry out the masonry, and construction is largely maintained.

For the manufacture of a metal collapsible form for one block, four rectangular iron plates with a thickness of 3-4 mm (height, width and waiter length will depend on the selected form size). On the sides of the plates it is necessary to cut fixing grooves, and to the end items of the form to privar handles. For a form of four blocks, you will need to make two rectangular plates and five smaller plates to separate future blocks in the form.

For the manufacture of concrete blocks with their own hands, a seal is required and creating bubbles in them, for this purpose it is necessary to make special adaptation. For it, one rectangular iron plate (in size) is required, a small piece of wire-rod cross section of 10 mm and three trimming pipe with a diameter of 50 mm and a length of 150 mm. At one end of each pipe, you need to cut through four "teeth" triangular shape to a depth of 50 mm. Then these teeth must be combined with each other so that it turns out the cone. The seams between the teeth need to be thoroughly brew. Then to one of the planes of the plate need to be welded a handle from the rod, and to the other - trimming the pipes with a blunt end.

Wooden collapsible form
Wooden collapsible form

For the manufacture of wooden collapsible form, you will need four cutting boards with a thickness of 35-50 mm (dimensions will depend on the size of the selected form). Of course, wood is weaker forms, so the boards are needed high-quality and strong. All compounds in a wooden form should be strengthened using tie screws. The rest of the wooden shape design is the same as metal. The handles for the shape can be made from the rod with a cross section of 10 mm, flattening its ends and drill holes in them with a diameter of 6-8 mm.

For the manufacture of building blocks, you need to make a solution from cement, sand and aggregate (slag or broken brick) in a 1: 4: 6 ratio. By adding an aggregate into the solution, it is necessary to ensure that it is viscous and sticky, but not turned out to be liquid or crumbly. Next, the solution is poured into the forms in which it will be glanced in hot weather for 2 hours, and the final fortress will acquire 1-1.5 days. With cool weather (+7 ... + 18 c), the hardening time and complete drying increases by 3-5 times, and at temperatures below +7 ° C and during precipitation blocks are not recommended at all.

If slag will be used for the solution together with the cement, you can completely abandon sand, and then the ratio of cement and slag should be 1: 6 or even 1: 8.

Before the fill of the solution in shape, all its parts are needed, regardless of the material of the manufacture, moisten with water. It follows on a flat surface and fill in a solution with a solution by 2/3 or 3/4 volumes ( exact amount Determined by the experimental way after applying the adaptation to do the voids).

After the block finally freezes, it must be released from parts of the form. The raw block must be left to completely dry, and the details of the shape pour with water.

You can make blocks directly at the construction site, i.e., to fill in place. In this case, the sizes of the form for the fill can be increased to 330 x 300 x 600 mm. This will speed up the construction process even more.

Consistency cement mortar And the fill method is the same as in the previous case. You can cook B. working construction Several forms (enough 3-4 forms), and then the laying will go faster.

To cement mix It did not stick to the walls of the form, before filling its inner cavity, it is necessary to richly moisten with water or lubricate the waste machine oil. After setting the mixture, the form plate flashed from the walls of the block. In the process of the construction of the walls, the horizontality and verticality of the rows should be recovered. In general, the laying of the angles, the digestion between the blocks is fully consistent with the methods brick masonry In Polkirpich.

Samama is a mixture of clay and straw, for the manufacture of homemade blocks

The cheapest building material for self-making concrete blocks at home is Samama - a mixture of clay and straw. Cheapness is not the only dignity of the Samana - this material is durable, with high thermal insulation propertiesEasy in production. For the manufacture of saman blocks, collapsible metal or wooden forms are also used. Better to do blocks small size, a maximum of 150 x 150 x 300 mm, because larger blocks are severe and inconvenient in work and besides, voids cannot be done in them.

On a note!

The lack of Samana is instability to humidity. Before the construction of walls from the Saman, it is necessary to ensure reliable waterproofing of the foundation, and the finished walls require shuttering with cement substance solution, covering any available polymer or metal grid and performing finishing finish.

Homemade Making Concrete Blocks for Construction

Procedure for the construction and manufacture of concrete blocks Standard: First you need to choose a place, then make a foundation - the construction of a tile foundation is required here, you can use foundation plates, sum up communication, build walls, building roof, install windows and doors and perform facing and interior design summer cuisine.

The walls are laid out in the Pollipich, for the summer kitchen, the wall thickness can be in one brick - and this will be enough. As it is masonry, you must unsubscribe walls vertically and horizontally using a plumb and cord, horizontally stretched from one corner of a house to another.

Homemade construction blocks makes it possible to reduce the cost of booking the outlook with subsequent installation of windows and doors. During the construction of a building in the building, you need to make door and window openings. Install the location of the windows and the door is still at the planning stage. It is possible in the process of masonry walls in places setting doors and windows to leave the openings of the desired width, as well as insert wooden plugs to which the franger boxes will be attached. Wooden tubes must be administered in the second row relative to the bottom of the box and in the penultimate row relative to its top. At the top level, the box should be installed with a reinforced jumper with a thickness of 120 mm or a thickness of 70 mm thick. The ends of the jumper should be started onto the walls by 20 cm. If the plane of the next row of masonry and the upper part of the frame will be at different levels, it will be necessary to catch up to the desired height, using parts of the blocks and the solution, or assemble the formwork, tie the reinforcement and pour cement mortar.

After the construction of the walls on the windows designated under the windows and the door door should be installed boxes, squeezing pre-corners. Next, you need to remove them horizontally and vertically and only after that you can attach the side pieces of the box to wooden corks using nails or screws. The remaining space between the walls, the foundation, jumper and the box must be filled around the perimeter of acrylic mounting foam.

The second way of the device of door and window openings is when the door and window boxes are installed in the right places, and then plated blocks. Usually this method is used when decorative masonrywhen the further decoration of the walls is not provided.

In this case, that the doorway in the process of the masonry does not behave, you need to press it on both sides of the first row, after inserting the backups in the corners. After the second row, it is necessary to align the box vertically and horizontally, fix it with nails or screws on the sides of the wall. It is also necessary to leave the release of 10 cm. Then, it is necessary to apply the solution to the releases and hold them by the next row by the block, once again convinced that the box is exactly exactly. The same must be done at the top door box, as well as on the fourth and sixth rows with a window box. The jumpers here are installed in the same way as at the first method.

Slagoblocks are popular construction materialFrom which buildings and structures of various purposes are built. Since they are easy to make at home, the machines for the manufacture of slag blocks are enjoyed. If you have free time and desire, then this equipment itself can be tried to build yourself.

The popularity of slagoblocks (as well as foam blocks) in their unique composition, and the machines for the manufacture of slag blocks not only allow to obtain a high-quality building material with limited means, but also make it possible to produce them for sale. For many, the production of slagoblocks has become a profitable activity that brings a tangible income.

Cement;
Granchlak (which is a deposit of foundry);
Special fillers.

As a result, blocks are obtained, which are characterized by high sound and thermal insulation indicators.

Making shape for slag block

In the network you can find the drawings of the machine for the manufacture of slag blocks of various complexity, for which it can be built with your own hands. These devices allow you to receive both hollow and solid blocks. The simplest device is a collapsible shape without a vibrator.

This form uses a concrete solution with an elevated water content. It is also called "soft."

The sequence of obtaining blocks in simple form

Filling with a molding box or matrix concrete;
Maintaining a solution in shape before setting (several hours);
Disassembling forms - the unit comes in a free state.

Council. Empties in blocks are convenient to form using bottles from under champagne, which are well suited in size and do not fight because they have thick walls.

Walls and bottoms in these forms can be made from metal plates or plywood sheets. Before pouring the solution in the form, it should be lubricated by spent engine oil.

Homemade machines with a vibrating device

Vibrostans for the manufacture of slag blocks are more advanced equipment. Getting blocks are faster and more convenient to them, as it is not necessary to expect a decay of the solution. In this case, the concrete solution is prepared tougher and thick, it should have a small shrinkage.

Technically, this is realized in two ways:

using the vibration table;

equipping the mold itself by the engine, on the shaft of which is installed eccentric with a displaced center of gravity.

The machine with an eccentric is more convenient for the production of a large amount of material, since it allows you to get a finished block into one approach without turning.

Articles on the topic:

Homemade machine according to the scheme "Nonaching"

The drawing of the machine for the manufacture of a slag block is one of the most simple.

The design includes such basic elements:

forming drawer - Matrix (it does not have a bottom);
vibrator on the side wall;
drawer handles designed for easy removal without damage to the shape of the cast;
replaceable clamping plates;
empty-formers for various shape of emptiness.

The current standard provides set sizes one such block - 39 x 19 x 18.8 cm. In this case, void should not exceed 30% .

Matrix manufacturing

Takes sheet metal (from 3 mm);
A form of one block is cut out of the sheet (5 cm for the mumbling is added to the specified dimensions;
A through box is formed (there is no bottom);

Important. Welding sheets is necessary outside, it will prevent violation of the correct geometry.

Special planks are applied to a large stability of the box. To do this is used profile pipes with a small cross section;
Upholstery based on the base of the matrix sheet rubberthat will serve to prevent the lower edges of the matrix of deformation;
An apron is formed for bonding, which will prevent the wake of the solution when filling out the form;
Handles are attributed.

Machine scheme

Below is the accurate drawing of the machine for the manufacture of slag blocks with an indication of the exact dimensions. Voids can be formed various shapes (rectangular or round).

Important. The push formator must have a conical shape, which will allow you to remotely remove the matrix from the raw slag block.

For the manufacture of a hollow good fit round pipes. The conical shape with this billet can be given using a lathe.

The vibrator is made of electric motor small power. For this suitable, for example, the motor from washing machine Power B. 150 - 200 W. The displacement of the centers is performed as follows.

On the axis of the engine attached an eccentric, which can be made from metal plank With asymmetrically located hole. Dimensions, weight and shape must be determined experimentally. If the magnitude of the eccentric will be too large, the vibration will be excessive, as a result of which the concrete cast will fall apart.

You can improve this design by installing a mobile platform with levers. This will make it easier to lift and move along the machine plot with a vibration-seeming node.

Stages of the process of manufacturing slag blocks

The formation of blocks is carried out in special forms that are pre-wetted. The solution is stacked in them. Forms are placed on a vibration plate, which is turned on for a few seconds (5 - 7 s);
As the solution is precipitated, it must be added. When you repeatedly turn on, the vibratinglitis should be expected to complete the clips to the limiters. This will show that the formation is completed. After 5 - 10 seconds (even until the motor stop), the form should be removed;
Ready blocks must be dried. This process takes from a week to month. Drying time depends on conditions (humidity, temperature, etc.);
The reduced equipment allows when working together for an hour to perform up to seventy blocks. If the amount is small, then the solution can be mounted manually. However, the concrete mixer allows you to get better material and the final product;
After the slag blocks are dried, they can be used to build walls - from blocks to build is easy. It must be observed simple rules - the first two weeks the blocks are watering with water;
After that, it should be covered with a double layer of plaster. This will prevent the shelter to rain. Per year from the material will be destroyed harmful substances And after that you can move to interior decoration and roofing work.

In our rapid time, all new products appear on the building materials market, which succeeds in many indicators of their predecessors. Interesting fact It is that some building materials can be made at home. The Russian people who are not spoiled by the money and benefits of civilization may come up with a lot in order to save and self-realize.

Purified production of block building materials

An explicit confirmation of this is the machine for blocks made with your own hands. He will need lovers who can build a barn, bath, garage, and even a residential building, from their foam blocks, gasoblocks, cerarmoblocks, slag blocks, sawdust-concrete (arbolite) and other blocks with different fillers. Knowing proportion component partsExperimental on the incoming ingredients, with it you can make a block building material handled on the construction of any premises and even on the foundation tab.

Various number of cells in shape

Depending on the scale of production and opportunities, the forms for blocks are made with their own hands, calculated on 1-2 products, 6-8 ed., 10-14 pcs., 21-30 units. et al. (Photo 1). They are designed for the manufacture of solid blocks and products with voids of various shapes. By changing the size of the matrix, you can produce blocks suitable for walls and for the foundation. Therefore, the size of the blocks and their number can be different (F.2). For ease of extract finished productThe collapsible structure should be provided. Material for the manufacture of forms can be metal, waterproof plywood, wood. Forms are a kind of removable opalkwhich allows you to make high-quality building material with the desired specified characteristics.

Photo 1 - Molds for blocks of various sizes
Photo 2 - Building hollow blocks

Photo 3 - wall blanks for forms
Photo 4 - Cylinders for filling voids

Stages of manufacturing forms for blocks with their own hands

For the manufacture of metal matrices, need sheet steel B-3 mm and metal pipe D 8 mm for the formation of emptiness, as well as Bulgarian, welding machine, other working instruments.

Prepared blanks for the walls. They can be cut at home with a grinder 450x210 and 220x210 2 stake. The bottom of the form should have a side of a height of 3-3.5 cm and a handle. On the walls are made of notches (F.3).
For the manufacture of emptiness Cylinders will be required (photo 4). To do this, the desired number of blanks at the rate of 3 units is cut off from the pipe. on 1 block. The height should be several mm smaller from the height of the walls. To give the pipe billet of the conical shape, on the one hand, it is necessary to cut the pipe to half the pipe and tinted with vice. Each pipe blank you need to brew on both sides, it turns out hollow plugged cylinders (fillers). They are welded to the bar, then inserted into the shape and the bar is welded to the walls of the form (f. 5).
Brew all seams It is necessary outside.
From a thick-walled plate We make a press with holes With a diameter greater than the diameter of hollow cylinders. The press must enter the matrix, about 50 mm. Handles are welded to the press (photo 6).

Ready forms for blocks do not require high costs. People who do not have special qualifications can work with them. The main thing is to perform the correct kneading and compact the contents.

Photo 5 - hollow cylinders are welded to the bar
Photo 6 - Manual Presha

Photo 7 - Drawing of homemade machine with vibromotor
Photo 8 - Phased Machine Machine for Blocks With Your Hands

Machines for blocks do it yourself

In order to be well the mixture for block building materials, you can use the vibrostol or make a machine for blocks with your own hands with a vibrator attached to the sidewall. In photo 7, a drawing of a vibratory machine is proposed. Ready design equipped with handles that help remove the matrix without damaging the raw concrete blank. Welded to the carrier frame of the wheel create a moving device.

Photo 8 suggests phased manufacture Equipment for one billet. It is similar to the production of forms without an engine. Attached vibrator makes it easier to work and makes ready-made building materials better. The use of machinery for the manufacture of construction blocks is completely simple. But when working with it should adhere to safety.