How to check the depth of a well after drilling. How to find water for a well: an overview of effective methods for finding an aquifer

The depth of the well for water is an indicator on which the quality of water and the cost of drilling depends. As a rule, it is the price of drilling that makes the owners of the site control this parameter. After all, for every extra meter you have to pay real money. If the work is carried out independently, then it is necessary to know the distance from the surface to the water mirror to select and correct installation pumping equipment. Therefore, it is desirable to understand how to measure the depth of a well after drilling.

The scale of drilling depends on the location of aquifers in the area and on the goals set by the owner of the site. If water is needed exclusively for watering plants, then it is enough to use the upper groundwater, which can already be located 4-6 m from the surface. However, such water is most likely not suitable for drinking, so you will have to drill much deeper to organize a full-fledged water supply system.

Interesting to know. Upon reaching the aquifer, water must be taken for analysis. If it contains a lot of pollutants and harmful elements, then drilling continues to the next horizon.

Professional drilling companies usually know the approximate depth of aquifers before starting work, using a geological map of the area and their experience for this. In the case of independent drilling, it is possible to find out the parameters of the well only after the completion of the process.

Soil section and location of natural sources

Methods for determining the depth of a well

There are several measurement methods that differ in accuracy, complexity and accessibility. Among them: simple mechanical way, available to almost everyone, as well as more technological tools used for professional research.

Weight and ruler

For this method, you will need a construction tape measure or ruler, a cord and a metal weight. To check the depth of the well after drilling, the weight is carefully lowered down. The descent is made until the tension of the cord is reduced, after which the homemade depth gauge is also carefully brought to the surface. Using a ruler, measure the length of the submerged cord, which will be equal to the depth of the well. At the same time, the size of the wet part can be used to judge the location of the water surface and the volume of the source.

Advice. For this method, you can use a special hydrogeological tape measure, which is made in the form of a flexible ruler with a load at the end.

Despite its simplicity, this method has significant drawbacks. Firstly, it can be used to check wells with a depth of no more than 10 meters. Secondly, the wet part of the cord will give an idea of the static water level, while the dynamic level is important for pump placement.

Tools for easy well depth measurement

Logging cable with magnetic marks

The principle of operation of the magnetic method is very similar to the previous version, however, it is made with a more technological approach. In this case, a wireline reel and a reader are used. On the cable, after a certain distance, magnetic marks are applied, which are processed by the receiving device and provide accurate information about the position of the load. In the intervals between the marks, the depth is determined by a special roller located on the coil.

This method is one of the most common when determining the depth of a well, since it gives an accurate idea of the location of deep aquifers.

Acoustic depth gauge

The operation of an acoustic depth gauge is based on the echolocation method. An acoustic signal is sent into the well, which is reflected from the bottom and recorded by the device. The time delay between the output and input signal is directly proportional to the distance travelled.

Such a device is often used in the mining industry, but it can also be used to measure the depth of a well for water. The only disadvantage of an acoustic depth gauge is high price.

Acoustic (sonar) depth gauge

Is it possible to trust the data sheet of the well

If drilling is carried out by a drilling company, then a technical passport is attached to the well, which indicates its main parameters. In the same document, you can check the depth of the well. But is it worth 100% trusting these indicators?

It all depends on the professionalism of the company. No self-respecting company will specifically add extra meters to get additional benefit. Therefore, in this regard, it is necessary to work with proven and experienced professionals who have a good reputation. And it is even better to be present during drilling operations, then you can personally verify the correctness of the calculation.

Advice. When using a specialized drilling rig, the measurement of the depth of the well is carried out after drilling is completed. To do this, count the number of rods used. It is desirable for the customer to be present during this process in order to check the correctness of the calculation.

Well drilling rods

When arranging a well, it is necessary to take into account many factors, including the cut of the soil, the nature of the aquifers, the hardness rocks and much more. Do it yourself drilling operations is possible only in case of shallow occurrence groundwater and low water quality requirements. If you would like to organize autonomous system water supply based on a clean source, then without professional help not enough. In this situation, you should not look for the most economical options. It is better to use an experienced company, and get a guarantee of full compliance with the real indicators and data entered in the technical passport of the well.

Video: well depth measurement

Own well allows you to use water, regardless of the availability of central water supply and its operating conditions. An important indicator when drilling is the depth of the well for drinking water. What it should be and how to determine the desired parameter, we will consider in detail.

The depth of the well for water: what depends on

Before developing a well project and starting drilling, it is important to determine the depth. There are several criteria that determine how deep you have to drill:

Level of location of aquifers. Test drilling or terrain analysis, taking into account the geological structure, will help to find out the indicator.
Site relief. On a flat surface, water can be located at a shallow depth; a hilly area is recommended to be drilled in a lowland.
Well assignment. The quality of water at the upper horizon does not always meet the standards established for the category of drinking water, so it will be necessary to drill to a greater depth. If the source is intended solely for watering the site, you can equip the Abyssinian well.
Debit well. In addition to quality, the volume of water received per unit of time matters to consumers. This parameter is the performance of the source, or debit. In Abyssinian wells, the indicator is 0.5 m 3 / h, in a sandy well the volume increases to 1.5 m 3 / h, the artesian source has the highest productivity, where the water flow reaches 3-4 m 3 / h.

The approximate cost of exploratory drilling of a well for water is 400-600 rubles.

Drilling depth, how to determine

Before drilling a well, it is necessary to find out the structure of the location of aquifers. The scores differ even small area, so orientation to a neighboring site is not always justified. Since there are no instruments that accurately determine at what depth the water is, the work is organized taking into account the data of test drilling in a particular region.

One way to determine the level of water occurrence is to analyze the vegetation of the site. Plants act as a kind of indicator of the presence of moisture.

Comment! Separate aquifers need to obtain permits for development, and their operation is accompanied by taxation. A well up to 5 m deep is not subject to registration and annual payment. An indicator over 15 m obliges to register the corresponding source.

According to the Law of the Russian Federation “On Subsoil”, it is possible to drill a well and use a source from the first aquifer without special registration. This category includes sand well and an Abyssinian well. Depending on the hydrogeology of the soil, in some regions the maximum depth without permits stops at 35 meters.

Core test drilling is one of the most reliable methods for determining the depth of a well for water. The appearance of wet sand is a signal to stop drilling. A break is necessary to fill the canal with water. Then it is pumped out and the debit is determined. With sufficient indicators, they proceed to the arrangement of the source. If the performance is insufficient, continue to drill to the next aquifer.

The characteristic of the liquid depends on the layer from which it enters the water supply system. Not all water is suitable for drinking, in order to determine the composition, after drilling, an examination is carried out in the laboratory. The horizon selected for drilling further determines the amount of the water tax.

aquifers

Before getting an answer to the burning question of how deep to drill a well, they deal with the diversity and characteristics of aquifers. The reservoirs that provide water for household needs are divided into 3 groups:

The upper one is called perched water, the depth varies from 4 to 7 m. There is no resistant water-resistant layer here, so water from the well is used mainly for irrigation and other technical needs. The liquid is often goes muddy due to the presence of sand and other impurities.
The second layer is located at a depth of 10 to 18 meters. Usually, drinking water enters the well from this formation.
Remark! After passing ground water through the filters of the well, the water becomes much cleaner than taken from the well. However, even here there is a risk of the presence of dangerous and harmful impurities. It especially increases during spring floods. Sometimes there is a smell of hydrogen sulfide. Water analysis for compliance with SES requirements, which is carried out by licensed laboratories, will help prevent poisoning.
Artesian waters are located on the third aquifer. The depth of its occurrence fluctuates at around 25-40 meters. However, the indicator depends on the relief of the site and sometimes reaches 60 m. Artesian water is considered the most useful and clean.

A visual diagram of the occurrence of aquifers is shown in the photo:

Types of wells

Autonomous water sources are divided into three types:

The use of perch water comes at the expense of the Abyssinian well.
Drilling to the depth of groundwater allows you to equip a well in the sand.
The artesian source is characterized by maximum depth.

The first type reaches a depth of 8-13 meters. Well water is used for domestic needs, including cooking. A feature of the design is protection against ingress of water from the perch into the source.

The arrangement of the source on the sand is carried out by auger drilling. The depth of occurrence is below the ground surface and is about 15-20 meters. The passage of water through the sand determines its purity, allowing it to be used for drinking. The operation of the well is possible periodically and year-round.

Water is considered ideal in terms of purity when drilling an artesian well. Private sources are equipped at a depth of 15 to 50 m, when used for industrial purposes, the drilling depth reaches 200 meters.

Comment! With regular maintenance, the period of operation of an artesian well exceeds half a century.

Drilling depth for drinking water High Quality individual for each specific case and depends on the hydrogeology of the site. One rule remains unshakable: the deeper you drill, the higher the probability of getting water intended for drinking.

Arrangement stages

It is better to entrust the design of a well to specialized specialists, however simple designs you can arrange on your own. The main stages of the process:

Determine the type of drilling in accordance with the characteristics of the soil.
Prepare appropriate machinery and equipment.
If the project provides for the installation of a caisson, dig a pit of the appropriate size. The height depends on the parameters of the equipment.
Drill the first section of the future water source, install the casing string. It is important to choose the right material so that its strength is enough to withstand the pressure of the soil.
Proceed to drilling the second section of the well, which is subsequently fixed with pipes.
When reaching a clay or sand formation, the drilling speed decreases. It is recommended to organize pumping and clean the filled hole.
Acceptable indicators of water quality and source performance allow you to proceed to the installation of bottom filters.
If the characteristics of the water or the debit of the source are unsatisfactory, they continue to drill to the next aquifer, which can be located 1-4 m below the previous one.
At the end of drilling, the casing pipe is fixed, the tightness is checked and the cover is installed.

At the final stage, they are laying the pipeline to the places of water consumption.

In order for the well to personal plot worked fully, it is necessary to install a stationary pump on it. And this cannot be done if there are no indicators for its depth. When a professional company is engaged in the creation of a well, the parameters of the depth of the well are entered in a special technical passport. Otherwise, you will have to think on your own about how to measure the depth of the well.

The depth of the well depends on the type of well.

Well Depth Measurement Technology

In order for the definition of the parameter of interest to be accurate, you should have:

Tools for measuring the well: a cord with a load and a building meter.

well passport;
pump or motor pump;
ruler or construction meter;
cord;
metal cargo.

If, nevertheless, the well was organized to order, then there will be no problems with the passport, since the working team issues it without fail. The first step is to read the document. Each company can have an individual filling form, but with certain standard indicators:

the depth at which the aquifer is located;
well depth;
casing diameter parameter;
indicator for the level of the aquifer.

From such a data sheet, you can take measurements of the depth of the well. But this document will only be available if the drilling was done professionally.

But with independent work, such a passport will be absent. But you can also deal with this issue on your own.

Measurement works are as follows:

Measuring the depth of the well with a special reader.

To measure the depth of a well prerequisite is good dry weather, preferably at the end of summer. It is during this period that the groundwater level is at its lowest level.
The ruler is used to measure the diameter of the well. Next, a load is tied to the end of the rope, which is lowered into the well. The descent must be carried out until the cord releases tension, that is, when the load touches the ground. After that, the measuring device is taken out. The level at which the rope is no longer wet is the height of the water, and the dry side indicates the statistical depth of the hole. Next, using a ruler, measurements of both parts are made. You can simplify the task. Before lowering the measuring cord into the well, colored tapes are attached at regular intervals, counting which you can determine the depth of the well.
You also need to know the dynamic depth. This will require a pump. The suction hose goes down to the very bottom, only initially it is necessary to put on a strainer at its end, which will prevent clogging.
Next, the device turns on, after which time is expected until it pumps out all the water. When a characteristic squelching sound begins to be heard, which will mean the completion of pumping, the pump turns off. After that, the measuring cord is lowered again into the remaining water. This indicator will mean the dynamic level.

This method is suitable for wells with an approximate depth of no more than 10 m. It is recommended to write down all the obtained indicators on paper, so you can make a home-made passport for the well.

It is important to know the depth of the well so that in the future it will be possible to purchase an appropriate pump that would work properly with this particular well.

Diagram of the location of aquifers.

In each locality, the level of aquifers can vary significantly. If recently drilling work was carried out in the nearest territory, then the depth of deposits of such layers can be found out from the workers. Although there is no guarantee that a well with drinking water in one and the other section will have the same depth.

There are always several layers of water in the ground, but you should be aware that not every one of them can be used in everyday life. For example, "upper" water often does not meet sanitary standards.

The first layer is usually located at a depth of 4-6 m. And a special sanitary examination will help determine the quality of the water, whether it can be used for everyday needs and whether it is acceptable in the diet. Most often, the first layer is not intended for operation.

The second layer can be found in the range from 10 to 18 m. It is this depth of the well that is suitable for extracting suitable water.

If for some reason the second level cannot be put into operation, then it is the turn of the third layer. Its average depth is 25-40 m.

Most wells are not drilled below the 50 m mark, as this level is quite sufficient to extract usable water. Although in a separate area a suitable aquifer can be found below 60 m.

Additional points

To make it easier to determine the depth of the well in the future, it is better to enter marks in this log regarding the location of the drill rod. The level of absorption of the circulating fluid, the depth of soil leaching, etc. are also entered into it. When one of the aquifers is reached, you need to take a certain amount of water for testing by specialists. They will indicate the quality of the fluid, which will determine whether to stop drilling or continue it.

By the way, several layers must also be said about drilling. If the site has large area, there is a possibility that each square meter may have its own levels of aquifers. Therefore, it is initially recommended to conduct reconnaissance of the area. The most elementary thing you can do is talk to neighbors who have already resolved this issue. And if you follow the technology, then you need to pay attention to such points:

relief of the terrain and levels of the earth's surface;
type of soil;
Are there other bodies of water in the area?
whether there are any sources of pollution nearby (factories, swamp, etc.).

By the way, a considerable distance must also be observed between the wells. Otherwise, there is a risk that both wells will not fully fulfill their purpose or one of the wells will not have enough water. And it directly depends on the type of soil how productive the source will be and how easy it is to create the desired depth of the well.

The presence of a well on the site will provide for yourself and family members autonomous water supply. Having your own water at hand is always convenient and convenient.

Every person who lives far from the city tries to ensure a normal life. This will require: sewerage, electricity and water supply.
Last on suburban area only possible under certain circumstances. There are wells and there are wells.
The depth of the well for drinking water can be different.

What is a well

Before you figure out how deep a water well should be in a suburban area, you need to determine what it is.
So:

It is one of the types of well.
It is a pipe well.
It has a small diameter, but can have a large depth, see photo.

Consider:

It can be different, which is intended for different needs.
There are such: for washing, for watering, for providing water (drinking), and so on.
The depth of the structure depends on this.
There are some that can be used not all year round.
For example, they can be seasonal, which are used only at certain times of the year.
There are also those that can be used on the site all year round.

Advice. Before designing a well in a suburban area, it is necessary to determine for what purposes the structure will be required and for how long it will be operated.

What determines the depth of the well

There are several factors that affect the depth of the well in a suburban area:

The location of the aquifer, which is necessary to meet the needs.
What quality should the water be?

Each site has its own places in which there are aquifers.
They can be located in each locality at completely different depths.
The terrain plays a big role in the construction.

Note. If it is flat, then there is a high probability that water will be around the entire perimeter of the site. If the terrain is hilly, then water is only in certain places.

For example, if there are hills on the site, then drilling at the top of the hill is not recommended.
This is due to the fact that the water terrain on the surface exactly repeats all the layers of soil at a depth.
This means that the water will be at a great depth.
It is best to drill in the lowlands or on a slight slope.

How to determine the optimal well depth

The depth of drilling wells for water can be different and you immediately need to determine it for your needs.

How can you independently determine the depth of the well:

In order to determine the optimal depth of the well in a suburban area, you can independently use several methods.
There are many folk signs.
They also use special frames that will indicate the presence of aquifers in the area.
Only with the help of such methods it is impossible to determine the exact depth. There are some errors.
For this reason, exploratory drilling began to be used.
This method allows you to accurately determine the depth of the aquifer.
It is carried out with the help of a drill and only specialists perform the work.

Note. Why entrust exploration drilling to professionals? This is due to the fact that only they can perform work in the way that the soil and terrain on the site require.

In the event that exploratory drilling is not carried out by professionals, then there is a possibility that in the process it will collapse with sand after reaching the aquifer.

Advice. To save time and money, you can use the services of a geodesy service.

More about geodesy:

What is geodesy? This is a complete analysis of the state of the soil and its layers.
It helps to accurately determine at what depth there is an aquifer.
The price for such services is not too high.
There is no need to spend money on exploratory drilling, but to equip it according to exact parameters.

Attention! Well, the presence and depth of perched water help to identify lakes or any other bodies of water that are located near a suburban area.

There is special equipment.
With its help, the pressure on the shore of the reservoir is determined.
Then they walk around the site with the device.
If somewhere there is a deviation of 0.5 on the sensor, then there is water.

Note. But here, too, one cannot do without additional exploratory drilling.

How deep can a water well be?

The depth of a well for water depends on the quality and quantity of water required.
The well may be:

allowed depth.
Deep must be registered with the relevant government organizations.
Permitted is the depth of the structure, which does not allow the use of the natural and unique bowels of the earth.
The depth that needs to be recorded can be quite large, and for this reason, the use of natural deep subsoil requires registration and a certain payment.

As a rule, both wells must be registered.
To use them, you need to pay a fixed amount of tax every year.
Only it directly depends on how deep the structure is.

Note. The permitted depth of a well for water starts from 5 m and ends at 20. In some regions, the permitted depth reaches 40 m.

There are wells

Verkhovodki.
On the sand.
On gravel.
On limestone.
Artesian.

As a rule, the depth is:

Verkhovodka - 5-6 m.
On the sand - 8-10 m.
On gravel - 12-17 m.
On limestone - 15-45 m.
Artesian - 50-80 m.

Attention! The quality of the water depends on the depth at which it is located.

Let's take a closer look:

The most optimal for irrigation is perch. The water in it is not very clean, but quite suitable for watering a vegetable garden or garden.
When arranging it, you still need to use filtering equipment. Only it should be with coarser filters (see), so that abrasive particles do not render it unusable.
Also, do not forget about the alluvial station, which will provide water supply.
A sand well is considered cleaner. This is due to the fact that sand is a natural filter.
It does not allow stones and metal impurities to penetrate into the water. It is also recommended to use powerful filtering equipment.
In third place in terms of cleanliness is a gravel well. It is also considered a filter.
Water goes already without admixtures of certain impurity and sand. In some cases, sand gets into the source. But this can only indicate that the well was drilled incorrectly or pumped in the wrong way.

Advice. After drilling, it is worth pumping it well. Sometimes even a few pumps are not enough, water with sand goes on for some time. Here, experts advise, in addition to one filtering station, to install additional similar equipment.

A limestone well is considered cleaner. It goes not only without sand, but also without metal impurities.
Water quality is several times higher than that of previous types of construction. It requires registration in some regions, as it is a natural source.
Artesian deep wells for water are considered the cleanest. They also require the use of filtration equipment.
Designs of this type are used only for industrial production. Purified water is extracted from them for the manufacture of products or for sale.
Water from such a source is useful. It is saturated with iodine and has high technical performance. Some doctors use artesian springs to treat patients and so on.

Advice. Artesian wells require a special permit for construction and state registration.
The tax for using such a source is quite high. For this reason, it will be unprofitable to build a structure on a suburban area.

You can bypass all these bureaucratic procedures and make an artesian well with your own hands and not register it, only then will numerous fines be imposed for non-compliance with the law and other mandatory taxes.

How to make a well yourself

Initially you will need:

Determine depth.
Draw up its project with full arrangement.
Determine the optimal equipment for its construction.
Count the number required material and equipment for full-fledged work source.

Depth of a well in a suburban area

Immediately determined:

In what period will the source be used.
What quality of water is required.
What is the purpose of the well?

Advice. It is best if the depth of the well is under drinking water will be larger and reach 20-40 m.

At a shallower depth there are seasonal wells.
Most of them are used all year round.

Drafting a project

In order to draw up a project, you do not need to have special experience.
More:

Initially, the depth of the well is determined.
Then the material for its internal and external arrangement is determined.
Pumping and filtering equipment for normal water supply is selected.
The project specifies the amount of material and its cost.

Selection of equipment for drilling a well

In order to drill a well, use:

Hand drills.
Drill columns.
Drilling rigs.

Hand drills are used at a depth of 5 m to 10 m.
Drill columns are used from 15 to 40-45 m.
Drilling rigs are already using from 50 m and deeper. They are considered more powerful.

Well construction process

After all the work on the preparation of equipment and material for the construction of the well is completed, they proceed to drilling.
Carrying out work:

For such work there is an instruction. All available tools are used: shovels, crowbars, buckets, etc.
Initially, a depression is dug on the surface with a diameter of at least 1 m and a depth of 50 cm.
Then inserted in the center hand drill and they work until it becomes difficult to pull out the earth.
After that, you need to use the drill columns. Only a few people can turn their valve. One cannot do this kind of work.
The principle of operation of the drill is that it is able to push the soil to the surface
Drill to the desired depth until water appears.
Then it is pumped out with the help of pumping equipment.
Then the water is collected again and its quality is checked.
After that, filtering equipment is installed and performed.

The video in this article shows the process of drilling a well. You need to drill a well in one day.
Otherwise, there may be structural collapses, and all work will have to be done again, but in a different place.

Not only the cost of the services provided, but also the quality of the water depends on the indicators of the depth of the well. Therefore, this factor cannot be left unchecked. We will tell you what methods exist for checking the depth of a well after drilling, what are their advantages and disadvantages, and how to protect yourself from deception, but get the desired result.

METHODS FOR CHECKING THE DEPTH OF A READY WELL FOR WATER

In this article, we will explain how to check the depth of a well after drilling. The required well depth is a determining factor for the quality of the water supplied and for determining the price. Most owners carefully control this factor, because when calculating the cost, each meter is paid. If you are drilling a well under water on your own, then you still need to determine the depth of the well as accurately as possible. This is required for accurate installation of the work equipment.

WHAT DEPENDS ON WATER DEPTH

Required depth wells for water depends on which balls of soil are located aquifers. It is necessary to take into account the fact for which you need this well. For example, if it is needed for watering plants, then it is enough to use water located at a depth of 4-6 meters. But it is not recommended to use such water for drinking, so larger drilling will be required.
We must not lose sight of the fact that when reaching aquifers, it is imperative to take water for analysis. If the first analysis shows that the level of dangerous pollutants in the water has been exceeded, then it is necessary to continue the work until the balls with accessible drinking water are reached.

WHAT WORK METHODS EXIST?

One of the advantages of working with us is that, using our work experience, we know what should be optimum depth so that you receive only high-quality water. To do this, our specialists use a depth map.
There are several ways to check the depth of a well after drilling. They differ in accuracy, complexity of work and availability.
Among them:
simple mechanical way
a more technologically advanced method using a logging cable with magnetic marks
measurement with an acoustic depth gauge
So, now let's talk about each method separately.

MECHANICAL METHOD

The first way is available to absolutely everyone. For it you will need a cord, a mechanical weight and a ruler. There are specialized hydrogeological tapes that simplify this process. To check the depth of the hole after drilling, it is necessary to lower the weight into the hole until a decrease in the line tension is noticeable. Next, carefully remove the devices and measure the length of the cord. The wet part of the cord determines the placement of the water mirror.
This method is very simple, but has a small minus. It lies in the fact that in this way it is possible to check the depth of wells after drilling up to 10 meters. The wet part of the cord will give an indication of the static water levels, but dynamic data is needed to properly install the pump.

CABLE APPLICATIONS

The second method is similar in principle to the first, but it uses more technologically advanced equipment that provides more information. In terms of accuracy, this method is the first, being the most popular in determining the depth of aquifers. The basis of the equipment is a coil with magnetic marks that transmit information to the receiver. The reel has a special roller, thanks to which the depth is determined.

PROS AND CONS OF ACOUSTIC DEPTH GAUGE

As for the application of acoustic depth gauge, this equipment is widely used in the mining industry, not only when measuring the depth of the well. This method is based on the reception of echolocation. An acoustic signal is sent into the well, then the tool measures the performance of the incoming and outgoing signals. The difference is directly proportional to the distance traveled, that is, the depth of the well. This method allows you to measure the depth of the well quite quickly. The only negative is that the equipment is expensive and it is unprofitable to buy it for yourself. If you want to use this method, it is better to turn to professionals.

IS IT POSSIBLE TO TRUST THE TECHNOLOGICAL PASSPORT OF THE WELL?

After the work is completed, any company provides technological passport well, which indicates the depth. Whether this document should be trusted is a moot point. It all depends on the professionalism and responsibility of the company with which you cooperate. You probably already heard about how they cheat when drilling water wells. A firm that values its reputation will not do this. Therefore, it is important to choose companies with good reviews clients.
If you doubt that you will be given the correct data upon completion of the work, then it is better to be present at the completion of the drilling of the well. The drilling rigs provide the final data and the installed rods are counted. You can control this process yourself.

CIMBERIA IS YOUR RELIABLE PARTNER

Kimberia has been a trusted partner for many years. We are trusted by many clients in the Moscow region. On request, the brigade will be able to as soon as possible travel to any area of the Moscow region. Thanks to many years of experience, we will be able to carry out work in any area and in any area, adhering to all quality and safety standards. And the price of services is affordable to absolutely everyone.
With us you can quickly and cheaply acquire an autonomous well in the country, near the cottage, country house. We will make sure that you always have clean and high-quality water. Turnkey modern well - optimal solution for years to come!