You will need bottles different sizes- 2L, 1L and 0.5L. Cut with scissors or sharp knife from each bottle the bottom is 3-4 centimeters high. Then in the center of each "saucer" obtained, drill a hole corresponding to the previously prepared threaded rod.

It is better to put saucers on the rod between two washers and two nuts. If you just use a metal pin, a wooden knitting needle or something like that as a rod, then the saucers can be planted on hot melt glue.

The bottom of the 2 liter bottle will act as the base of the stand, so just turn the saucer over to stabilize the whole structure.

2. Boxes for pastries and cakes from plastic bottles.

Cakes and cupcakes tend to wind up, and it can be difficult to bring such beauty to a visit safe and sound. Not scary! Make such crafts from plastic bottles do it yourself - boxes for sweets. From a cardboard circle and a half of a bottle, you get a box for one cake, and in two halves of a bottle you can carry delicious macarons!

3. A small box - a do-it-yourself plastic bottle case.

Cut from two liter bottles bottoms 5 - 7 cm high. C inside hand-sew on a small zipper.

4. DIY organizers and stands from plastic bottles

Plastic bottles provide tremendous opportunities for organizing the workplace. Bottles can be used to make a variety of organizers for magazines and correspondence, tools and sewing accessories, stands for stationery and cosmetics, boxes - baskets for toys and other small things. We simply cut off the neck from the bottles, and then - at your discretion. A few simple options below will give you ideas.

5. Do-it-yourself curtains from plastic bottles.

Do-it-yourself unusual crafts from plastic bottles - curtains or light partitions for zoning the space. These curtains look like floating transparent flowers shimmering in the sun. Interesting decor not only the interior of the house, but also verandas or terraces in the country. A detailed master class with photos can be viewed.

Crafts from plastic bottles with your own hands for a garden and a summer residence.

1. Feeders and drinkers for birds with their own hands.

You will not surprise anyone with such a bottle craft. In the surrounding parks and forests, as well as on balconies, various bottle and milk box feeders can be seen everywhere, especially in winter time... But, perhaps it will still be interesting for you to look at what other feeders you can build with your own hands from plastic.

2. Vertical garden on the wall

Empty concrete walls of a house, garage or fence just ask to be decorated. It's a good idea to arrange on bare, lifeless walls vertical garden from plastic bottles with your own hands!

You will need a couple of dozen two-liter plastic bottles, scissors, rope (twine or wire) and two washers per bottle. The process is shown schematically in the figure:

For drainage, you can make a couple of holes in the bottom of the container - a bottle, and put small pebbles, sand or special filler in front of the soil. And you can grow a whole vegetable garden in such hanging gardens: herbs, spices, flowers, berries and medicinal plants!

3. Seedling lids.

The half of a plastic bottle makes excellent seedling caps that protect young sprouts from wind and bad weather.

4. A boat made of plastic bottles.

An extraordinary invention - a boat made of plastic bottles, which is almost in no way inferior to the factory model made of wood or rubber. If you have a desire to acquire such a boat almost free of charge in order to navigate a nearby lake or river, you will find a master class.

5. Do-it-yourself flower beds from plastic bottles

You can use halves of plastic bottles to decorate the garden and fence off the flower beds or beds. Moreover, seedlings can grow under the bottles. Such garden crafts from plastic crafts even children can do it with their own hands.

6. Hose nozzle - plastic bottle sprinkler.

Lovely garden idea for soft watering of plants in the garden. Take a plastic bottle and make many small holes in it. Then place the bottle on casters such as an old cart, toy stroller or rollers, attach a hose to the neck and turn on the water. Small jets from the holes will water the plants like rain, and the wheels will allow the sprinkler nozzle to be mobile.

Could human waste in the form of plastic bottles be an interesting project for home and garden? How can they! American designer Garth Britzman has created an extraordinary canopy from plastic bottles with his own hands for parking.

Such a canopy made of plastic bottles gives shade, which is important to prevent the car from heating up, but will not save you from rain. In addition, the underside of the canopy looks bright thanks to the tinted water at the bottom of the bottles.

How to make a canopy out of plastic bottles with your own hands?

1. As a basis for the canopy, build wooden frame from four vertical bars and horizontal bars.
2. Pull a net, woven or wire over the crossbars - we will hang bottles on the stack.
3. Prepare plastic bottles with caps. V this project canopy, 1500 liter bottles of various drinks were used. Remove labels, wash bottles.
4. Consider the color scheme for your canopy. It can be a certain drawing, an image (smile, sun, symbol) or just an abstract pattern, a gradient transition of shades, and so on. It is not easy to imagine the whole picture. However, starting from the desired result, start filling the bottles with tinted water. You can pour water on the very bottom. You can paint the water with both food dyes and water-soluble paints for painting.
5. In each cap, make two holes in the middle and tie a strong thin rope or fishing line. You can punch one hole at a time, thread a rope and with back side tie a large knot lids.
6. Screw the caps with a rope onto the bottles and start hanging them by the net according to the diagram. Also, bottles can be hung at different heights, this will add volume to the canopy. The bottles can be glued together. Then the canopy made of plastic bottles will not walk so much from the wind and get tangled in threads.

7 ways to use plastic bottles in the garden

1. Make a plant watering system

Majority garden plants you need to water at the roots, especially if you combine watering with fertilization. The plastic bottle can be turned into a drip irrigation system, which can be used to deliver moisture and fertilizer directly to the roots of plants for a long time. Punch a few small holes along the length of the bottle with any handy tool. Bury at the same time as planting seedlings. The water from the bottle will slowly flow to the roots. This simple tool solves the problem of dead leaves and prevents mold and mildew from growing.

This system can be used in open ground and in flower pots, slightly redesigning. Cut the bottom of the bottle so that the neck buried in the ground does not reach the bottom. Fill the reservoir with water if you leave the plants without watering for a long time. From the bottle, water will slowly seep into the ground and nourish the flowers.

2. Make flower pots

Old bottles and containers will act as a mold for filling homemade flower pots... Take plastic bottles interesting shape, cut off the top. Prepare cement mortar and fill the shapes by about a third. Then insert another smaller plastic container inside to create a bowl. The next day, the inner inserts can be removed to make a drainage hole in the bottom (using a drill or any convenient tool). After another couple of days, you can remove the outer plastic shell.

3. Make a system for growing seedlings

It is not enough just to pour soil into the jar and stick the seeds in there. We still need to germinate them. For everything to rise, do in plastic cans drainage holes, fill containers with soil and plant seeds. Place the cans on a pallet lined with small stones or pebbles. Cover with cling film to make a mini greenhouse. The seedling speed system is ready.

4. Make a self-irrigated seedling system

The methods of growing seedlings can be improved and made from plastic bottles a design that will save you the need for watering. Cut the bottle in half. Punch a hole in the lid. Take a thin lace 25 cm long, fold it in half, and tie a knot approximately in the middle to form a loop on one side. Pass the loose ends of the string through the hole in the lid and close it. Insert the upper part of the bottle with the cap down into the lower part. Pour in water so that the ends of the rope are immersed in it. Place soil, plant seeds, water the plants to saturate the soil with water. Ready!

5. Grow onions in a plastic bottle

Make universal vertical bed for fresh herbs. Cut off the throat of a large plastic bottle and punch holes in the body (not too low). Fill with soil to the first hole, cover them with bulbs inserted with roots inside the bottle. Continue backfilling with soil. Fill the entire container, place on the pallet. Remember to water and harvest fresh herbs.

6. Make a wasp trap

Find vespiary in a garden or in a suburban area it can be difficult, and clouds of insects interfere with work and rest. Make traps out of unwanted bottles. Cut off the top of the bottle, place it neck down in the second part (without the cap). Pour some honey on the bottom. The wasps will be able to go down, but not get out.

7. Make another watering system

It's simple. As a child, we splashed with water, punching several holes in the bottle cap. If you make holes in the bottle itself and attach it to the hose, you get a watering can with a wide radius of action.

It would seem - how can we use empty plastic bottles that we constantly encounter in everyday life? Yes, they are very different - big and small, from carbonated and drinking water, from ketchup, sauces, mustard, shampoo, cream ...

Most of us throw plastic bottles in the trash can without regret. But, it turns out, completely in vain! Even such seemingly useless things can be put to very good use:

• Crafts from plastic bottles for a garden, a summer residence and a vegetable garden;
• Balcony ideas;
• Children's crafts and toys from plastic bottles;

Animals from plastic bottles

• Flowers from plastic bottles;
• Useful for the home;
• New Year's ideas;
• Bird feeders;
• Drinking bowls from plastic bottles;
• Consider what can be done from caps and corks from plastic bottles;
• Flashlights

So, let's look at all the points and find out what crafts from plastic bottles can be made using a little imagination.

Children's crafts and toys from plastic bottles

Of course! Toys and toys again. Piggies, cows, cats, lions, penguins. Just look closely at the bottle: what does its shape remind you of? Grab your paints, brushes and have fun and enjoyment!

For inspiration, here are examples of what toys can be made from plastic bottles of different shapes:

Creative French have created a whole world of robots out of plastic bottles and caps!

The best children's books

A whole detailed step-by-step instruction on how to make an airplane from a plastic bottle

Show me at least one boy who would refuse such a jetpack made of plastic bottles!

And here is a great toy for the bathroom - boats made of shampoo bottles.

Such a colorful and cheerful elephant will help to add variety to the interior of the children's room and will simply delight your children:

If children are afraid of the dark, make a funny night light for them and with them.

Idea source: Fab

Or such "fireflies".

You can also make bright and funny rattles for the little ones from plastic.

And here are these "foam blowers" for older children - in the summer they will use the street great success the kids.

It turns out that plastic bottles can be used to make not only toys, but even a whole game! For example, how do you like this bowling alley?

And, of course, you can very easily make a traditional piggy bank! True, it will be difficult to break it. 🙂

Animals from plastic bottles, birds

The main thing is to guess the animal hidden there in each shape of the bottle!

Look what a cute jellyfish from a plastic bottle for decorating your desk room!

Magic Video Turtle Making Master Class

Funny birds from plastic bottles.

Charming princess frog

Christmas crafts from plastic bottles

Christmas tree made of plastic bottles

It turns out that you can make a Christmas tree (for example, a tabletop), and even a Christmas tree from plastic bottles. Links to master classes are under each tree.

And in this video, a girl makes a tall Christmas tree with a star on top of her head!

And one more video Master Class on making a New Year's beauty

Christmas toys from plastic bottles

Christmas toys in holidays we need it in order to decorate the tree or the whole room. Here are some ideas to help you make the unexpected and funny. Christmas toys and jewelry practically out of nothing - from plastic bottles and a minimum of improvised means.

The Christmas tree can be decorated with the help of these original balls (such balls are based on rings cut from a plastic bottle, and you can create any decor):

Can be made simple Christmas decorations do it yourself - and depending on how you decorate them or what you fill them with, you can get many options:

If you have a large tree, you can make golden bells for it:

Or you can - cones from brown plastic bottles:

Christmas decorations for the home from plastic bottles

Snowflakes most different types look especially good if you can paint them with gold paint:

Such a ball can become a decoration of a room, and a few balls hanging at the entrance to the house will create an unforgettable festive atmosphere:

It is very, very simple to make Christmas candlesticks from plastic bottles:

Useful crafts from plastic bottles for home

Comfortable pouf for the living room

Step-by-step instructions for making a charming cat pots

We all know how delicious cupcakes are and how difficult it is sometimes to bring them to a visit without ruining all the beauty. Ordinary cake boxes are too big for them, and for some reason no one has invented mini-boxes. So make them yourself! You will need nothing at all: a plastic bottle, cardboard and colored tape.

By the way, you can also pack macaroons in the same way!

Here are some more ideas for creating a variety of containers from plastic bottles for storing various items:

Source of idea and MK: duitang

We don't know how for you, but always for us a big problem find a place for a charging phone. With a shower gel bottle, you can easily solve this issue. Just cut out a holder from it, which will fit both the phone itself and the charging cable. And you can decorate it with a cloth or napkins using decoupage technique.

Plastic bottles will help even for unusual design rings for napkins. We offer step-by-step instructions for manufacturing.

Bird feeders from plastic bottles

Maybe the bird feeder is not the best creative craft, but very useful for our smaller brothers, and it also deserves attention, especially with the approach of spring.

Make two holes through the bottle, insert a wooden culinary spatula. And, of course, don't forget to add the grains!

Crafts from plastic bottles for the garden, vegetable garden and cottages

Now let's see how plastic bottles can help us grow flowers and other plants.

This idea will save a lot of space, because a previously empty wall is used to place these pots.

Perhaps the simplest, but such an important craft is a watering can for home or garden plants! It is not so important whether you are preparing to grow seedlings for the garden at home, or you just have aromatic herbs growing in pots - such a watering can can be very useful.

And you can do it just with the help of a bottle, a match and a thick needle!

Fun with water in the form of a whole system of iridescent vessels is ideal for summer pastime with children in the garden and in the country.

And to whom are fly agarics from plastic bottles?

Or a whole bunch of daisies!

Jewelry from plastic bottles

The imagination of the designers amazes! You look and cannot believe your eyes that such wonderful things are created from ordinary plastic bottles!

You can create jewelry for girls:

Step-by-step instructions on how to make a very delicate bracelet

Craftsmen and beginners use plastic bottle crafts for the interior, as garden decor and in the form practical furniture... Colored plastic bottle caps - great stuff for mosaic panels on walls and hedges. Best ideas with detailed instructions and the photo is easy to embody in the country, turning the bare area into a "glade of fairy tales", and fill the house with useful little things.

One of the most crazy hands Runet Roman Ursu presented a crazy video in which he showed 70 ways to use plastic bottles.

Advantages of crafts from plastic containers

A well-made souvenir or trinket will eventually grow into a hobby if there are no limits to imagination. Summer residents, who have moved from simple hedges on a wire to buildings that delight in scope, do not cease to admire.

From available material, which many throw away, someone builds:

• greenhouse;
• carport;
• summer shower or bath;
• country toilet or shed;
• summer gazebo or sun shade;
• teremok for children or playground;
• sandbox with decorative bumpers;
• various temporary buildings on the site.

Over time, plastic becomes a real environmental disaster - it is difficult to recycle it. But it is worth attracting all those who are not indifferent to cleaning the territory, and there will be a whole mountain of empty PET bottles for the construction of a greenhouse, a cascade flower bed or vertical gardening... The only drawback is long collection identical containers, since containers are produced different color and volume.

To create an original jewelry you need:

• interesting idea;
• ready-made role model (illustration);
• material for crafts with tools;
• a step-by-step guide to the training plan.

In the hands of a real master, plastic bottles find a second life, becoming functional objects. Souvenirs are best done on a seasonal basis. For example, Christmas toys are made in winter, practical country buildings- in the summer, and in the spring and autumn, it remains to build a "meadow of fairy tales" near the house for children.

Furniture and interior items from plastic bottles

Furniture made from plastic bottles looks like a masterpiece that is not available to everyone. They will need a lot of plastic containers of the same sample. Sofas and poufs impress with their design and comfort, not inferior to real furniture. There is nothing complicated if the sofa is made in blocks - seat, back, sidewalls. If the container is not enough, the blocks of the sofa can be made one by one. Better when collecting bottles from under one drink, for example, a two-liter kvass or lemonade.

The principle of "assembling" furniture from bottles is simple - they are laid out in layers and tightly wrapped with tape. To make the furniture softer and more springy, a little air is released from each bottle and screwed tightly. To the place where the lid is, cut a cap from another bottle and fasten it with tape. It turns out a block with a bottom on both sides - this is the basis of the furniture.

Then it all depends on the imagination, the type of furniture and the number of bottles available. We wound up with tape 7 containers of the same volume, it turns out the basis for the ottoman. What will be its appearance and style depends on the master. For a soft seat you will need round pillow or a block of foam rubber according to the size of the top. The cover is cut to fit the ottoman in the form of a cylinder, and it is convenient to insert a zipper along the side seams, but it is easier to sew the upholstery tightly.

For construction coffee table you will need 4 racks of plastic bottles and a plywood board as a table top, which can be hidden with a long tablecloth. In a similar way, they make a comfortable stand for a laptop or a portable table for a summer cottage. For large furniture (sofa, chaise longue or armchair) made from plastic bottles, it will take a lot of patience and starting material.

Useful little things for home from plastic bottles

Flowers and vases

Decorating a student's bedroom or children's room with crafts from plastic containers is not difficult. You can build a whole bunch of artificial flowers. Put the resulting chrysanthemums, chamomile or roses in a vase of the same material, complementing the middle with diode bulbs on an insulated wire. This will look like a night light of extraordinary beauty, where a weak light shimmers in plastic petals.

Advice: To give the leaves a special shape, use heating the blanks and folding the corners with tongs!

To place a homemade bouquet, you need a suitable vessel, just cutting off part of the bottle is not aesthetically pleasing. The edges of the cut are marked with a ruler to make a cut, securing the result by heating the folds. A small transparent bottle is cut off to the very top, about half of a large container is cut off. Choose a material with a ribbed or “waist” in the middle for an interesting base.

Then we do it as our imagination allows, but bend the edges beautifully. The fringed cut is obtained from vertical or diagonal notches of the plastic base. The resulting stripes are bent evenly to the outside.

Note! It is important that all the notches and the depth of the slot are exactly the same, then the whole product will come out neat.

Depending on which edge is desirable, the strips of the vase (the edges of any other product) are fixed in different ways:

• curly bend;
• staple staples;
• fusing;
• bonding with transparent polymers.

Planters, flower pots and seedling containers

Colored plastic containers in the form of bottles and bottles of different sizes are suitable as containers for growing live plants. It is very easy to make a fragrant balcony from 3-liter cisterns - a cascade of ampelous petunias. Fragrant flowers hanging from cut containers will help to realize the dream of a beautiful corner of paradise.

Large bottles and tanks, cut in half, are hung with the bottom down and with the lid. It is recommended to lay large pebbles at the bottom for drainage. Excess water after watering will go to the plants in the lower rows. Plants are grown in the same containers without soil - hydroponically with the addition of fertilizers. Fresh greens and seedlings (in urban and suburban conditions) are also germinated in prepared plastic bottles.

Advice: Use the compact shape and the ability to hang the vertical gardening containers with automatic irrigation... In the absence of the owners, watering cans with water, immersed in the ground, will cope with the moisture of the plants.

Traps and feeders

Use plastic bottles to repel pests or attract birds to your area. For this, the tank is used as a feeder, and at the roots fruit trees place traps from bottles of chemicals. From a double plastic container, craftsmen construct traps for wasps, where they fly into sweet water and cannot get out.

Suburban area equipment

At the dacha "at hastily»It is easy to make crafts from plastic bottles in the form of an impromptu washbasin, hanging a full bottle upside down. Unscrew the lid a little, and a small stream of water will help wash and wash your hands. It is also worth making a bench and organizing lighting with beautiful owls or gnomes from their plastic. Any garden decor for inspiration - in interesting illustrations.

Multifunctional items for the home

Make an original cosmetic bag from 2 bottoms of plastic bottles, sewing the edges with a zipper. This box can be used as a multifunctional item - a piggy bank, a case for large beads, hairpins or jewelry.

It is convenient to knit from a similar ball, suspended somewhere nearby, pulling the thread from the ball inserted inside. Nail polish or lipstick collection is easier to find in a makeshift zippered jewelry box.

New Year's decor

Original all seasonal flower beds

The summer season is passing, and home-made plastic flowers, which are not inferior in beauty to the real ones, are replacing living flower beds. Their advantage is the ability to decorate the territory at any time. These flower gardens fade against the background of living plants, but in early spring and in late autumn only they attract rapturous glances.

Small plastic containers are needed for daisies. white(petals), yellow (middle) and green (leaves). You will also need an awl and a candle (for warming up), "liquid nails", scissors and a stiff wire in green insulation.

Cut the base of the white bottle to the center, marking out 16 segments - these are the petals. We bend the neat edges over the candle flame, we also make 2-3 chamomile corollas, which we connect in the center with an awl. Here a stem with leaves is fixed on a green wire, closing with a middle. We fill the center of the flower with a yellow basket with small cuts from 2 finely dissected circles with a fringe curved over the candle. We supplement the flower with green sepals from the bottom, collect all the parts and fix them together.

From the remaining pieces of green plastic, cut out leaves with a hole at the base (for stringing) and give the desired shape, warming up over a candle flame. We attach the leaves on the wire handle, they should slightly bend around it. It remains for the chamomile to make several "companions" and find a worthy place for the bouquet.

All seasonal flower beds include mosaic compositions from containers filled with earth. They make from the lids wall panels... "Butterfly" or "ladybug" - in different versions.

Crafts from plastic bottles for the playground

The incredibly beautiful bird with plastic plumage is a whole "meadow of fairy tales". This is a peacock or firebird, swans, pigeons, bullfinches and parrots. They are all made from empty PET bottles according to the general principle:

1. Design an aesthetic bird head with eyes and beak;
2. Build the torso and neck;
3. String on plastic plumage;
4. Equip with wings and tail;
5. Place on the legs or fasten to the selected surface.

Plastic swans can be fenced off with a blue "lake" of inverted plastic bottles. Outlandish birds will decorate the trees in the corner of the garden, which is reserved for children's games. You can choose themed décor, such as a desert island with palm trees and parrots.

The material is collected for a whole year, but it is easier to connect neighbors and acquaintances to the idea of ​​"ecological" cleaning. There are special containers for plastic in the yards - it's much easier to type.

Preparation for work - removing labels and glue residues from plastic bottles, it is important to rinse well and discard deformed material.

If vertical fences are being built, they need to be filled. Depending on the idea, sand, stone chips or dry soil are poured into PET bottles, burying 1/3 with the neck down.

For selected purposes, plastic of different elasticity is used. Heat treatment is required for filigree work (flowers). It is important not to overheat the slices cut into strips.

For fairy-tale characters, additional painting is sometimes required. For example, it is better to cover pink piglets for a playground with an aerosol from a spray can, securing it with transparent acrylic paint.

Plastic bottles are great stuff in the right hands. Using them as a basis, it is easy to teach children a lesson in environmental education and fill a house or lot with practical things. At creative approach the color, volume and shape of plastic bottles will themselves suggest new ideas for an exciting creative process.

Tags:,

Plastic bottles in everyone's life they have firmly taken their place as disposable containers and their use is only in the form of containers, but we can get much more benefit without throwing them away. For most people, a bottle is useless, but if you are smart, you can find many ways to make your life easier and save money with bottles. From a plastic bottle you can make almost everything, you need the bottles themselves and a little imagination.

Sprinkler for the garden.

One of the simplest ways is useful apply the bottle in the vegetable garden or garden- make of it garden sprinkler, it is nowhere easier to make it. We attach a plastic container to the garden hose and make several small holes, then we tightly fasten the hose to the neck. In this way, we made a sprinkler for the garden.

Advice.For convenience, use a square container or secure a round one with a weighty object.

Frequent case, wire charger lacking from socket to place where can I put mobile phone, everything can be fixed by making a clumsy holder for your mobile phone... It is necessary to cut the bottle diagonally, take the bottom and cut at the top round hole under the outlet. Now the phone will lie in the bottom with a socket.

Advice.It is better to cut the bottle as close to the top as possible, this will allow you to hold the phone more securely.

You lose every time stationery, you have to look for them, you need to make it easy to manufacture stand... In addition, the bottle will need a bolt and nut. You need to cut off the top and bottom after drilling a hole in the plug and the bottom and connect with a bolt with a nut. It will be convenient to use this since it turns out 2 departments. In the upper section pens and pencils will fit, and in the lower section there are paper clips, buttons, graters and you will not have to get pens because of little things.

Advice.Tighten the bolt and nut loosely, then the top will be able to scroll.

Empty canister with manual, it is not necessary to throw it away, it can be useful if you do not need it or has become unusable, it will turn out scoop... It is necessary to mark the canister with a marker as in the photo and cut it.

Advice.For convenience, make the nose of the scoop square.

Glass jar lamination.

We use glass jars for different purposes and you have to mark them in all ways, but the inscriptions do not hold well on the glass, and the glued papers quickly become unusable, and laminate there is no possibility. With the presence of an industrial hair dryer, this problem is solved forever, while the strength of the dishes will increase. If you break it, you won't have to pick up the pieces and cut your own hands. Having shown imagination, the jar can be well decorated. It is easy to do, you need one bottle, suitable in size and color, and a piece of paper with an inscription or a picture that we want to attach. However, there is a way to do without an industrial hair dryer.

Method one.

Cut off the top of the bottle and place it on the bottom with the cork up, then put the jar on the cork with the inscription put on gloves and start heating the industrial hair dryer. When the hair dryer heats up, you can begin to gently heat the jar in a circle, without lingering in one place. You need to take a stock, the plastic will settle both in width and in height. When the jar is tightly tightened with plastic, cut off the excess and reheat the angular parts, if all the parts are flat, the jar is ready.

Advice.Start heating the plastic from the bottom, gradually rising.

Method two.

Cut off the top of the bottle and put the jar with the glued inscription on the bottom. To heat the plastic in this case, we need a high pot of water and kitchen stove... The pot should not be full or water will splash onto the stove. When everything is ready and the water boils, we lower the bottle into boiling water and begin to turn it slowly, holding the neck of the glass jar with tongs.

Advice.By holding the jar at an angle, the effect will be achieved more quickly.

Are you bored balls of thread confused with each other and stuck in nodes, the way out is simple - from bottles of any size we make a device for holding the threads in one place... At the same time, the tangles will rub less, get confused and get stuck. You can make a holder with attachment to a chair or armchair. We cut the bottle closer to the neck, leaving the part that must be cut in the form of a rectangle to the bottom, after which we make a hole in the resulting tail to the size of the cap and put it on.

Advice.The device can be hung by making holes on opposite edges and threading through them.

With the onset of cold weather in every house, everyone turns on possible types heaters and at the same time indoor air becomes dry and we begin to experience discomfort. Headaches, skin problems, mucosal irritations and other inconveniences can be avoided by making a quiet, simple, convenient and reliable indoor humidifier. For this you will need:

• Duct tape
• Scissors or knife
• A strip of fabric, or lace
• Two liter bottle
• gauze cloth

Advice.Pouring into a container essential oils we get an air freshener.

Instructions

1. In the side of the bottle, we make a slot 5 × 10 centimeters, errors are permissible.
2. We hang the resulting bottle with strips or a cord on the straight upper pipe entering the battery with the hole up and tightly fix it with tape so that the bottle does not jump out and spin.
3. We smooth the gauze several times to get a rectangle 10 centimeters wide and a meter long.
4. Place the middle of the folded fabric in the hole, and wind the ends around the battery tube.
5. Pour water into the resulting container and moisten the wound gauze, this is the maintenance of the device.

Mosquito trap

From a two-liter bottle make a mosquito trap... The trap will attract small insects through fermentation processes, namely carbon dioxide. For manufacturing you will need:

• 1 gram baker's yeast
• two liter bottle
• dark fabric
• 50 grams of sugar
• 200 ml of water with a temperature not exceeding 40 degrees

We begin manufacturing with cutting in such a way that the neck, upside down, fits tightly into the bottle and lacks water. Now that the container is ready, pour out the sugar, yeast and fill it with forty-degree water, it should not be warmer or hotter. If the liquid is too hot, fermentation will not start due to the death of the yeast bacteria. Pour water slowly and mix the mixture. Now we insert the neck into the bottle in the manner of a funnel. In order for mosquitoes to come across, the trap must be covered thick cloth, not transmitting light or paper. Once in such a trap, mosquitoes will not get out. Insects will fall into such a trap for up to a week after which we will change the mixture.

Advice.After preparing the mixture, put it in a warm place.

From several one and a half liter bottles we make a simple and extremely durable broom... It is convenient to sweep the floor and fluffy surfaces with such a broom. The stiffness of the broom depends on the number of cut pieces.

Manufacturing.

To begin with, we make blanks. Cut off the neck and bottom, dissolve the middle into flaps to the middle, no wider than two centimeters. You will need 4 of these, and leave one more top with a neck. Now we put everything together, and cut off the top of the next bottle, put it on what happened and squeeze it. We take a strong wire and pass it through all the bottles around the edges. We put everything on the handle through the cork and fasten it with wire. For reliability, we drive a nail through the neck into the handle.

Advice.Use copper stranded wire.

If in nature we did not have mugs you can easily make it out of a bottle... To begin with, we cut off the top, then using a knife or scissors we cut out a square, retreating 2-3 centimeters from the upper cut. We cut it out exactly and with the expectation that the width of the remaining jumper will be the handle. Turn the top ring inside out and push in the bottom. Now we got a mug that can help us out in nature.

Advice.Without cutting out a large square, you can roll up the middle section and slide the cork ring over it.

Create self-watering flower pot just cut off the top of the bottle first, then the middle part, so that the top goes in without touching the bottom. After that, we carefully make a hole in the cork and thread a thread into it. The thread should protrude 5 centimeters from both sides of the cork. Now that everything is ready, pour in the water and insert the upper part that looks like a funnel. Now we fill up the soil, not forgetting to wet it. The plant will absorb the right amount of liquid, this will make it easier to care for the plants.

Advice.Fertilizers can be added to the tank.

Arriving in nature you forgot the cutlery nothing to notice them. To save the situation, a bottle, a knife, and a lighter are enough. Cut out one of the five parts of the bottom and a little of the upper part in one piece, then burn the edges with a lighter. You can eat and prepare food with this spoon.

Advice.Rinse the appliance after burning.

Not all refrigerators provide vegetable cells and you have to store vegetables in a variety of forms, while the products are beating, scratching and rolling all over the refrigerator. For convenience, use a 5 liter eggplant. Cut off the top and fill with vegetables or fruits. In this form, the food will not wrinkle and the free space in the refrigerator will become noticeably larger.

Advice.Store vegetables and fruits in separate containers.

During the cooking process, it is required separate egg white or yolk... But they are not easy to separate, the yolk is very fragile and if punctured, it will mix with the protein. You can cheat with a bottle. Split the egg into a plate, squeeze the bottle and bring it to the yolk. Unclenching, we will pull the yolk into it without damaging it. The method is suitable for cooking dishes, the recipe of which includes a lot of eggs, for example, the popular French meringue dessert "Merengue".

Advice.Rinse bottle before use.