As experts advise, in order to reduce fuel consumption, you just need to develop a so-called economical driving style. Simply put, this means that you need to handle the gas pedal carefully, that is gently press to accelerate and brake due to the engine which shuts off the fuel supply. This will really help reduce fuel consumption. But the percentage of savings will not rise above 10%.
Some gas stations offer to simply switch to cheaper types of fuel that contain a higher percentage of ethanol. But this can affect the operation of the engine, as well as the fuel system. In other this problem can only affect certain brands of cars.
V Lately among drivers, the method of using the so-called "super device" has become very popular. Its principle of operation is to break up the clumps of gasoline molecules due to magnetic resonance, and then the combustion of gasoline occurs with less waste. So, experts categorically do not advise using this method, since this is just pumping money.
In fact, significant savings can be additional installation in the car gas equipment. The cost of installing such a technical device can cost an average of $ 700 to $ 1,000, depending on the brand of car. But this method can be beneficial only with a high mileage of the car., because otherwise the installation of HBO will pay off for a very long time. Be sure to consider the type of engine, because not all engines function normally with gas.
The most daring way to save money is home gas filling. In appearance, it resembles a wall-mounted gas boiler, which is accessible at any time. Since the cost of natural gas for the population is approximately 5 rubles, and if we take into account that 1 cubic meter of gas is equal to 1 liter of gasoline, it turns out that such filling stations provide savings by 5-6 times.
But in all this there is a huge minus. home option gas refueling will cost about 5 thousand euros - this is the minimum, plus the installation of gas-balloon equipment, which is adapted to natural gas. The capacity of the compressor for pumping gas is not high, so refueling can take several hours. And to top it off, you must always carry an 80 liter gas bottle with you in the trunk.
To speed up the refueling of the car, the owner can arrange a receiver station. What does it mean? First, pump gas into stationary cylinders, and then refuel the car directly from them. This procedure will be shortened to 20 minutes.
But if the driver has a small car, then the installation of a home filling station is unprofitable. It can be more profitable for owners of gazelles or jeeps, in which the fuel consumption coefficient is very high and can be up to 20 liters per 100 kilometers.
Gas fuel has firmly entered the life of modern man. So, gas bottle is a rather primitive device, but it also has a number of specific nuances. Next, you will be able to read about what they are gas cylinders, but for now we will try to determine the purpose of the gas itself.
There is an erroneous opinion that gas "locked" in a cylinder and gas in a pipeline are one and the same. The fact is that centralized gas supply uses methane, which is a natural gaseous substance, it is also called swamp. But gas cylinders are already filled with a mixture of propane and butane, which is also officially called SPBT. A mixture of propane-butovy technical is a by-product obtained during oil refining. In the future, he will use the wording SPBT or simply “gas” for it.
Propane-butane mixture is absolutely universal. It is widely used in the petrochemical industry for the manufacture of polymers, as well as in mechanical engineering and metalworking - for welding work and cutting metal surfaces. In addition, SPBT can act as a gas engine fuel.
Complete diagram of connecting a gas cylinder to a stove
In everyday life, such a gas mixture is used to sell autonomous gasification Housing and communal services. It refuels gas tanks and various gas cylinders in which gas is burned by the forces of domestic boilers, stoves and other household appliances. gas equipment. Carbon dioxide and water act as combustion products, for this reason such combustion is considered as safe as possible for the ecology of living space.
In cross section, a gas standard cylinder is similar to the design of a transparent gas lighter. The gas mixture in a liquefied state acts as a liquid, and the free space above it is a steam cap, which enters the boiler or stove. The balance between these media is maintained due to the pressure inside a special container.
Connecting the cylinder to consumption devices
The device must be connected via a reducer. Inside a conventional gas cylinder, the pressure is not constant and depends on the ambient temperature. It can vary from 4 to 6 atm. The reducer is able to lower and equalize the pressure to the optimum operating level of the cooker.
A hose is connected to the reducer, and a plate is connected to it. The place of fixation is fixed with clamps, after which it is necessary to check the tightness of the connection with soap suds. Any foam will do. The fixation points must be covered with soapy water: if bubbles form on the surface, then the connection is leaky.
We eliminate the leak: tighten the nut even more at the junction of the fitting with the gearbox. If a leak is found in the sleeve area, then tighten the clamps. After adjustment, it is necessary to check again with soap suds to make sure there is no leakage. This test is always carried out when connecting gas bottle- it Golden Rule safe use.
Correct connection of gas cylinders on the street, figure 1
Correct connection of polymer-composite gas cylinders, figure 2
IMPORTANT! You should not act like some especially “experienced” gas masters: in no case do not check the tightness with lit paper. This results in small flames at the leaks. This is strictly prohibited by safety regulations. In addition, such flames are very small and in daylight can go unnoticed and lead to sad consequences.
Installation and operation of gas cylinders
The most important criterion for the safe operation of such devices is the control of possible leaks and overheating. Violation of sealing can be detected by a characteristic odor. The gas, in principle, has neither color nor smell, but a special marker is added to SPBT - a hydrocarbon-mercaptan. Due to this, a person can smell when the gas stove column is turned on or during a leak.
So, if you smell this smell, then we can conclude that the concentration of SPBT is 20 percent of the dangerous one. There is no reason to panic, that is, a reason to check the junction according to the above scheme.
Operation of gas cylinders, presented in the form of a table
When the gas cylinder is in the room itself, it should be placed at a distance of 1 meter from the stove, which in the active state is a heat source. Also, any other heating devices should not be placed nearby: heating radiators and autonomous heaters.
An acceptable option would be a "country" installation method - from the outer north side of the structure, which eliminates the possibility of overheating the balloon by the sun's rays. In such a situation, the sleeve must be passed through a hole in the wall, previously “treated” with a metal sleeve. The cylinder is placed in a special metal cabinet equipped with ventilation holes in the lower part of the walls. Since the gas is somewhat heavier than air, in the event of a leak, it will accumulate from below, where there will be ventilation holes, so a light wind can eliminate unwanted accumulation.
Why are the cylinders covered with frost?
Here you can also debunk one of the most common misconceptions. It is generally accepted that if such a device "freezes", then it becomes covered with frost. Some even argue that it is necessary to insulate such equipment with blankets, old coats and other improvised devices. So, the frost will disappear faster if the gas container is left as it is, without helping it to “thaw” with warm clothes.
The bottom of the gas cylinder, which is covered with frost
The appearance of frost can be explained by a number of physical processes that occur inside the structure when it is connected to furnaces or burners. At such moments, active fuel consumption is observed, therefore, large volumes gas liquid turns into a vaporous fraction. And such a phenomenon is always accompanied by a large consumption of heat, it is for this reason that the surface of the cylinder becomes much colder than the temperature in the surrounding space. Moisture in the air space begins to appear in the form of condensate on the walls of the installation, subsequently turning into frost. This is a completely natural phenomenon, with which nothing needs to be done.
Moreover, all attempts to use artificial "insulation" violate safety standards during operation, and also affect the deterioration of heat exchange between the device and environment and affect the conditions of gas supply. If your burner did not please with a grandiose flame, then after your “maneuvers” with a blanket, it may stop working altogether.
Do not insulate gas cylinders with anything!
In general, when connecting gas appliances with high power, you need to be aware that the gas cylinder has limitations in terms of recoil speed. This means that the liquid fuel is converted into the steam stage gradually. For example, a 50 liter tank can provide about 500 grams of gas in 60 minutes. This is equivalent to a power of 6-7 kW. In the cold season, this figure is halved if the equipment is located outside. In summer, the situation is reversed: the maximum flow rate increases.
In any case, it can be concluded that frost is evidence that the cylinder cannot cope with high fuel consumption. This can cause a temporary drop in gas pressure and equipment failure. If this happens, it is better to stop consumption and wait until a sufficient head of steam has formed.
Why is there a "splash" of water in the container?
This can be heard in winter. Know that this is not water, but the butane component of SPBT. At the slightest frost, butane ceases to be converted into a vaporous fraction. It is she who "splashes" in the form of a liquid inside.
Butane component of SPBT in a gas cylinder
In the warm season, this problem does not arise: almost the entire propane-butane mixture is used. In order to avoid this in cold weather, it is recommended, when filling the tank, to ask the refueller about the availability of a passport for the used SPBT. This document must contain information that the mixture contains at least 80 percent propane, which passes from liquid to vapor during cold weather. If you use such a dressing, then there should be no problems.
How much gas is enough?
Here you can use primitive mathematical rules. If we start from the power of the stove, where 4 burners work at once, then 8 kWh of energy is used in 60 minutes. If you burn 1 kg of gas, you can get 12.8 kWh of energy. The first result must be divided by the second figure, resulting in the amount of "liquid" fuel required for full-fledged work cooker for an hour. This figure is 0.625 kilograms of gas. Therefore, a 50 liter container with 21 kilograms of gas will be used to run the stove for 33.6 hours. If the power in kg of fuel burned is indicated in the passport of your equipment, then the calculations are greatly simplified.
In the future, everything depends on the intensity of use of the plate. If you often brew jellied meat, then the degree of consumption will be one, if you are content with only brewing morning coffee, then another. Based on practical experience, we can say that 12 liters of gas, which will be used by a small family on weekends in the country, will be enough for the whole summer. You will find more detailed information about autonomous gasification in this section.
How to fill a gas bottle?
Refuel such devices on the territory of special points, which can be located autonomously and enter the gas station. In the conditions of the latter, it is possible to refuel with gas motor fuel.
The most important nuance in this process is the fact that you need to refuel not by volume, but by weight. As a safety measure, gas containers should be filled to a maximum of 85 percent of the total volume, in order to avoid excessive pressure.
In order to follow safety precautions and its standards, such a device with any volume is marked with a number with a maximum allowable weight, corresponding to the same allowable 85 percent. The tanks are placed on the scales, including fuel injection. The process stops after reaching the required weight.
But even when refueling relative to the mass, overflows are not excluded, which is especially important for small-volume containers - by 5 or 12. They should be refueled by 2 and 6 kilograms, respectively. The high speed of refueling sometimes does not allow you to see the achievement of the limit rate. If this happened to you, be sure to ask for the excess gas to be drained. In the future, it is better to choose another place for refueling.
In general, the basic criterion for choosing a tanker is the availability of license documents for the use of fire and explosive objects. If the documents are present, then we can conclude that you are served by qualified specialists who annually undergo special certification.
In other cases, you take responsibility for the operation of the refilled container. And you risk not only your money, but also the safety of your home and life. In addition, an unlicensed gas station is a violation of the law and may entail not only administrative, but also criminal liability regarding the article on illegal entrepreneurial activity.
The information provided in the review does not claim to be accurate encyclopedic data and is largely dictated by our experience. But we are sure that it can help you save a lot of time and money.
In many country houses gas cylinders are used, which must be regularly refilled. Although they are used in production. Refilling is much cheaper than buying a new cylinder. They are used for heating and domestic purposes. When living outside the city limits, the question of where to fill the gas cylinder becomes natural. This is discussed in the article.
Pros and cons of gas cylinders
The self-contained tank is a convenient thing to use. Its advantages include:
- Mobility. It can be rearranged, transported.
- Unlimited storage period. It can be used later.
- Big choice. You can purchase a container of any size, purpose, made of various materials.
Of the minuses are:
- Fire hazard. If the tank is located in the area of a fire or a sudden change in temperature, this can lead to a threat to life and health, as well as damage to property.
- The presence of sediment in old tanks with prolonged use. They need to be cleaned for future use.
- Gas leakage if the equipment has been used for a long time. You need to change the jet regularly to prevent this.
- Danger from sudden overturning. There is a risk of a pressure surge and a sudden burst of flame. And it’s almost impossible to pay off everything on your own.
- Risk of substance inhalation. If the equipment is malfunctioning, then people living in the house can be poisoned by carbon monoxide.
Where to apply?
Household gas cylinders are sold at specialized points. Usually there is home delivery. Where to fill the gas cylinder if it is empty? In these specialized centers, the filling of containers is carried out. As a rule, these points are located at stationary automobile gas stations.
Other items
Where else is propane? There are several options:
- Factory. But this option is not very convenient, besides not cheap.
- Companies that have received the right from Gostekhnadzor. These include the exchange of cylinders.
Factories and companies must have special premises that meet the requirements, as well as the equipment that is needed for such work. Where to fill gas This work is performed by the same specialized points.
Where should you not go?
Although you can perform this procedure at almost every gas station, where there are not even special balloon points, you should not buy liquefied gas there. This is quite risky because:
- After this procedure, there is no check for gas leakage.
- There is no control of tankers, which is why the use of such gas equipment will be unsafe.
- Due to the format of the filling column, the balloon cannot be filled with high quality.
According to the norms, the filling volume should not exceed 85%. This creates a "vapor cap" in the cylinder, which protects against the risk of the cylinder exploding due to high temperatures. In automobile cylinders, in comparison with household ones, there is a cut-off valve to prevent gas overflow. Therefore, the equipment must be checked on the scales. Where is the best place to fill a gas cylinder? You can also apply to car gas stations, if only there is special equipment and a license.
Filling process
Refueling centers are called gas filling stations. They may have different equipment. Usually the procedure is performed in 3 ways:
- Pumped: A pump is used.
- Pump-compression: the gas is taken with the help of a pump and enters the cylinder under high pressure of the compressor.
- Pump-evaporator: in the gas supply system there is a heater-evaporator that provides increased pressure.
All refueling methods are safe if the rules and procedures are followed.
station requirements
If you are interested in where you can fill the gas cylinder, then you should check the station for the presence of:
- Exhaust and pump installations.
- Reservoirs for gas.
- Technical tools for transportation.
- Additional devices - dispensers, devices for measuring the density of a substance.
Where are household gas cylinders filled in cities? Usually they do this gas services who connect and maintain this equipment. They deliver containers with the substance according to a certain schedule. Gas equipment is also delivered to the villages, delivered by special vehicles.
The procedure is performed according to standard requirements. They must be observed, as there is a risk of explosion. For example, the procedure is not performed if there is one of the shortcomings:
- the equipment is faulty;
- there is no necessary pressure in the cylinder;
- there are valve or valve defects;
- rust is visible on the surface;
- peeling paint;
- there is damage.
Therefore, you need to check compliance with these regulations regarding where you can fill the gas cylinder. They should be labeled "compressed gas". A sticker is also attached, indicating an explosion hazard. Only in this case, everything complies with safety standards, so refueling in such a company can be performed.
Refueling rules
Before the procedure, the balloon is freed from condensate and remaining gas. Filling is carried out on the basis of the characteristics indicated in the data sheet, so that the equipment will work safely. During the procedure, there should be no fire, sparks, coals and other hazardous substances nearby. Work can be done in 2 ways:
- Exchange. A person gives away his reservoirs, and he is provided with filled ones. This saves time. But the disadvantage is the receipt of other equipment, which may not have quite high-quality parameters.
- own balloons. A person leaves their tanks for refueling, and after a while picks them up. Then only your equipment will be used. But you will have to spend money on shipping and wait a while.
After refueling, the equipment must be properly maintained. It should not be affected by precipitation, sunlight. Cylinders should be stored upright. Equipment should be checked regularly for proper operation. It is better to eliminate any defects immediately, without waiting for adverse consequences.
What does the price depend on?
It is important to know not only where to fill the gas cylinder, but also the price of these services. The cost depends on:
- service level;
- availability of transport services;
- electricity costs;
- gas prices.
In case of violation of refueling procedures, firms are held liable. If they do not comply with the rules and regulations, then for these cases it applies. Therefore, if you need to fill a gas cylinder (50 liters or another volume), you should contact specialized companies that work on the basis of a legally issued permit. Then the procedures for filling the cylinders are performed correctly, which is safe for the life and health of people.
Recently, a new offer has appeared on the market of gas-balloon and filling equipment - mobile (home) gas filling. In other words, you can fill up your car at home from the domestic gas network. As you know, domestic gas tariffs for the population are orders of magnitude lower than gas prices at gas stations. And this is even through the counter. If there is no meter and you pay at standard (albeit overpriced) rates - then everything is clear. Yes, it turns out that you will fill the car almost for nothing. By the way, in the West or in America such homemade gas stations are gaining more and more popularity, although there the difference in the price of gas in the kitchen and at the gas station is not at all big. We have another thing...
With savings, I think everyone understands - even according to the most conservative estimates, at least more than 10 times, provided that you honestly pay everything according to the domestic gas meter.
In addition to that, refueling a car with natural gas from a household network, brought to your house or apartment will allow:
Again, the main thing is to reduce the cost of refueling the car. The cost of methane is several times lower than the cost of gasoline. The more intensively the car is operated, the higher the economic effect.
Extend engine life. Methane gas, like propane-butane, does not wash off the oil film from the engine cylinder walls, which provides excellent lubrication of piston group parts. In addition, methane, unlike gasoline, does not contain various additives that oxidize the oil itself, which has a positive effect on the resource and stability of engine oil characteristics. Plus, this, by about a quarter, extends the life of spark plugs. Reducing the wear of engine parts increases the engine life by 1.5-2 times, and the service life of engine oil by 2-2.5 times.
The high octane number of natural gas (104-115) allows it to be used for any engines (ZAZ, LuAZ, VAZ, GAZ, Moskvich, UAZ, etc.), as well as in the engines of most foreign cars. This also applies to trucks.
Significantly reduce emissions of harmful combustion products into the atmosphere. When using gas as a car fuel, there are no emissions of harmful toxic compounds of lead and aromatic compounds, emissions of CO, CH, nitrogen oxides are reduced by several times, smoke from the exhaust pipe is reduced three times. Even if you are not an ardent admirer of the "green", cars with methane LPG installed are exempted from environmental control during technical inspection.
And the expediency of using various "devices" to reduce the fuel consumption of a car has already been considered earlier.
Further, there are two options for refueling a car with gas at home:
Purchase a ready-made factory mobile gas filling station. Unfortunately, the domestic industry does not produce such ones (it is understandable, no one will be given permission), and there are already quite a few foreign samples. For example, Neuman ESSER (Germany), Maschinenfabrik (Austria), Litvin (France) and many others are mass-produced. The only, but very significant disadvantage is the price. These gas stations are not cheap, especially for a person who wants to save on this, and therefore, definitely not an oligarch.
Do it yourself. The option, again, is ten times cheaper, but it requires desire, time and, most importantly, "straight" hands, besides, they must grow from the right place;).
Guide for self-production of a set of gas-cylinder equipment for refueling a car with household gas
At the beginning, it is necessary to clarify: there are gas equipment for compressed gas and equipment for liquefied gas. Compressed gas equipment uses ordinary natural gas - methane, which can be taken from an apartment household or industrial gas network. The only problem is how to fill this gas into a car at home.
In a conventional gas pipeline supplied to a home stove, column or boiler, the pressure of natural gas is about 0.05 atm., And in a gas cylinder high pressure up to 200 atm. Therefore, a compressor is needed that will raise the gas pressure to the required value. The design of such a compressor is somewhat different from that used in conventional home appliances.
A conventional single-circuit compressor is able to raise the pressure to a maximum of 20 -25 atm., And to fill a gas cylinder, you need to reach 200 atm. This is achieved by adding additional circuits to the system. It looks like a set of several compressors, each subsequent one, of which pressurizes the gas previously compressed by the previous one to a higher pressure.
In general, the high pressure compressor circuit looks like this.
Designations on the diagram: 1 Gas filter at the inlet. 2 Stage 1 inlet valve. 3 Stage 1 exhaust valve. 4 Cooling tube between 1st and 2nd stages. 5 Inlet valve stage 2. 6 Exhaust valve 2 stages. 7 Cooling tube between 2nd and 3rd stages. 8 3rd stage inlet valve. 9 Exhaust valve 3rd stage. 10 Cooling tubes at the last stage of gas release. 11 Pressure switch. 12 Active carbon / molecular filter. 13 Safety valve. 14 Pressure sensor. 15 Outlet fitting to hoses.
The principle of operation of the compressor for refueling cars with gas:
Gas from the domestic domestic gas pipeline through the inlet filter (1) is supplied through the inlet valve (2) to the primary circuit cylinder. Compression occurs and through the exhaust valve (3) through the pipeline through the cooling radiator (4) is fed to the cylinder of the next circuit. Further, the gas pre-compressed in the primary circuit is compressed to an even higher pressure. All processes are repeated in the third circuit. The number of circuits can be increased to five. There are three of them in the diagram above. But this does not change the principle.
Compressed to the required pressure, natural gas (about 200 atm.) Passes through the pressure switch (11), is cleaned in a molecular filter and fed through the safety valve into the tank of the fueled car or into the reserve high pressure tank. The refueling time will depend entirely on the productivity of the plant.
In order to speed up the refueling time of the car, you can use additional stationary cylinders. Then, in his spare time, the compressor pumps gas into these stationary cylinders. And when you need to quickly fill up your car, you distill methane directly from them. Thus, it is possible to reduce the refueling time to 10-15 minutes.
Description of a home-made device for filling a car with domestic gas.
As previously stated, this requires a high-pressure compressor (up to 200 kg/cm2). You can use compressors such as GP4, NG-2, AKG-2, but they require a powerful electric motor, which is not suitable for many. A good option is to use the AK 150C air compressor. It is used on modern armored vehicles and in aviation. This compressor is rather small-sized, lightweight, and requires a low-power electric motor of 1.5-3 kW, which allows it to be connected to an apartment or garage electrical network. The main question is where to get it. But believe me, this is not such a difficult task as it seems at first glance. It often happens that they can be written off, while using up no more than 10% of their resource. Whoever seeks - he will always find (sometimes for very little money or liquid barter :)).
The scheme of the filling device is shown in fig. 2
From the home household gas network through a rubber hose (possibly from a gas welding machine), gas is supplied through a valve to the gas filter (7). The pressure meter (2), connected through an adapter (3), serves to control the pressure in the gas network. The gas in the filter (7) is cleaned of impurities and fed to the compressor (10), where it rises to 150 kg/cm2. Then the gas enters the dehumidifier (18), the high pressure gas filter (19), the automatic pressure switch (20) of the ADU-2S type. After that, the gas is supplied to the filling valve.
When the pressure rises above 150 kg / cm2, the ADU 2 valve opens and the gas returns through the tube (23) to the compressor inlet. The pressure gauge of the NMP 100 type is used with measurement limits of 0-400 mm of water. Art.
The function of the gas filter can be performed by a new fine fuel filter for diesel engines. A valve (17) is used to drain the condensate from the water separator. A manometer (22) (0-250) kg/cm2 is installed to control the pressure at the compressor outlet.
Elements 18, 19, 20 (Fig. 2) are most preferably used from air system tank. In principle, you can do without the ADU-2 pressure automatic device, but then you need to constantly monitor the outlet pressure so that it is not exceeded.
On fig. 4 shows the layout of the holes and the main parameters of the compressor. The compressor does not have its own drive unit and lubrication system.
Figure 3 shows a variant of the compressor drive assembly.
It is attached to the compressor flange (1) with the help of tin, studs in flocks (8) through the gasket (10) housing (11). From below, a plate (12) is welded to the body for mounting the compressor with a lubrication unit (Fig. 5). A bearing (4) of type 205 is pressed into the housing (11) (Fig. 3). A bushing (7) from a slot is pressed into the bearing, which is fastened with a retaining ring (19). On the one hand, the splined shaft (6) of the compressor enters the sleeve, and on the other hand, the shaft (17) is pressed in, the key of which enters the splines of the sleeve (7). This is to avoid splines on the shaft (17). After pressing, the shaft (17) is carefully attached to the sleeve (7) by welding.
After that, the body (11) is closed with a cover (14) with an oil seal (13). The cover is fixed with bolts (5). A drive pulley (15) with a key (16) is pushed onto the other end of the shaft (17). The compressor lubrication unit is shown in fig. 2 and fig. 5. The tank (24) (Fig. 2) serves as the base, which can be made from a rectangular profile or welded from tin. A drive unit with a compressor is attached to the top of the tank. The hole (13) (fig. 3) must match the hole (11) (fig. 5) of the tank. A hole is cut out on top of the tank in a convenient place, to which the filler neck (3) and the cap (2) are welded (Fig. 5).
A hole is drilled in the lower part of the tank for the drain plug (14) (Fig. 2). A hole is drilled in the side wall of the tank for the oil pump (1) and the pump drive shaft (17). The oil pump is attached to the tank wall with studs. The hole (4) (Fig. 5) serves to supply oil to the pump. Shafts (6) and (17) are connected with plate (7) and bushing (8). The bearing (12) is fastened with a housing (15) with a cover (16) and an oil seal (13). The cover is attached to the body with bolts (14). A pulley (18) with a key is put on the shaft (17). The oil pump is used from a GAZ-51, 52, 69 car, but it should be borne in mind that the pumps differ in the length of the drive shaft.
To control the oil level, a viewing window (11) of an arbitrary design is used. The lubrication system works like this. The torque from the electric motor pulley through a belt drive is transmitted to the pulley (16) (Fig. 2), (18) (Fig. 5) and through the shaft (17), bushing (8) and plate (7) is transmitted to the shaft (6) pump drive (1). The oil enters through the hole (4) into the pump (1) (fig. 5), (8) (fig. 2), passes through the adapter (3), into which the automobile pressure sensor (4) is screwed and is fed through the tube to the inlet fitting (12) oil supply to the compressor. Fitting (12) in fig. 2 is conditionally deployed. It is screwed into the hole (3) (fig. 3), The diameter of the thread depends on the tube you have, which can be used from hydraulic system autotractor units.
Then the oil passes through the lubrication channels of the compressor (fig. 3, fig. 4), collects in the lower part and is thrown out through the oil drain hole fig. 4, fig. 11 (det. 11) then flows through the hole (13) (fig. 3) into the tank (24) (fig. 2) Part of the oil passes through the bearing (4) (fig. 3) and lubricates it. Detail (7) ( Fig. 11) can be made from a compressor drive gear, which must be purchased. To do this, grind the ring gear to the dimensions shown in Fig. 11 (det. 7). An automobile bulb can be connected to the pressure sensor (4) (Fig. 2). Instead of a sensor, you can connect a pressure gauge for control. In order to divert the gas that has broken through the piston rings into the body of the drive unit, there is a threaded hole at the top of the body (Fig. 11), (det. 11), section A-A, into which the fitting (13) is screwed (Fig. 2). A rubber tube is put on the fitting and is brought out above the roof of the garage, at home. Although the design of the filling device provides for the localization of possible gas emissions into the room, it is desirable to install it outside the room.
The design of the compressor allows you to pump gas of any pressure. But it must be remembered that when the compressor is operating at a very low pressure or the complete absence of gas at the inlet, with the main valve fully open, a vacuum may be created at the compressor inlet and the compressor, instead of gas, begins to draw air through leaks in the valve seals, etc. Therefore, before when filling gas into a cylinder, it is necessary to let the compressor run for several minutes into the atmosphere until the air is completely removed from the filling device.
Re-equipment of the car to run on natural gas.
On fig. 1 pictured scheme of gas equipment for natural gas.
First you need to make sure that it is appropriate to install HBO on your car.
Cylinders (5) containing natural gas are connected by high pressure pipes (3) through adapters (4) screwed into the cylinders instead of valves. Through the shut-off valve (6), gas is supplied to the flow valve (9) and enters the high pressure reducer (HP) (11), where the high gas pressure (200 atmospheres) is reduced to 10 atm. During this process, the gas cools rapidly and strongly, so the reducer can freeze during a fast gas intake, then the gas will stop flowing. To prevent freezing of the gas, a reducer heater (12) is used. Further, the gas is already through the low pressure pipeline (14), through solenoid valve(15) enters the low pressure reducer (18), where the gas pressure is again reduced and sent through the tee (20) to the car carburetor (22), in proportion to the engine load (depending on pressing the gas pedal). By transferring the voltage of switch P1 to the EM gas valve (15) or to the gasoline valve (23), it is possible to switch the type of fuel on the go. Gasoline enters the carburetor (22) through the fuel pump (24), valve (23). The start valve (19) is used to start the engine on gas.
On fig. 1 shows a simplified diagram of the control of EM valves. Valves 15, 19, 23, reducer-heater 12, low pressure pipes can be used from the set of equipment for liquefied gas. All this can be mounted in the engine compartment in their regular places. This can be done in a workshop for installing liquefied gas equipment. You can also purchase these units there, install, adjust, and check. You can do all this on your own, but you still need documents for registration gas installation by car, and they can only be issued by a licensed workshop. Yes and for correct adjustment gas equipment, on which both engine thrust and consumption are very dependent, it is desirable that a qualified craftsman would perform it on the appropriate equipment.
You don't have to buy a balloon. A standard car will not work, because it is designed for low pressure (16 atm) and the mileage will be very small. Therefore, it must be replaced with a high pressure cylinder (Fig. 7) 200 (150) atm and a high pressure reducer (11) (Fig. 1) must be added to reduce the pressure from 200 (150) atm to 10 atm. Aviation oxygen reducers that do not freeze well, or a reducer from a truck with a heater, are well suited for this.
Also, for this purpose, you can use a conventional oxygen reducer for gas welding. But it needs to be modified a bit. It is necessary to change the cover with a large thread diameter, at the top for a fitting and a safety valve with a fitting from the gearbox of a truck. The fact is that the oxygen reducer is not suitable for gas removal when the safety valve is triggered or when the membrane breaks. A rubber tube (10) (Fig. 1) is put on the safety valve fitting and the cover fitting (13) and is led out of the body.
In addition, for the oxygen reducer, it is necessary to purchase a liquid heater (12) (Fig. 1) with a bracket. In this way, you can reduce the cost of the system. It should be borne in mind that the above applies to the oxygen reducer type DKP-1-65. There is also a new type of gearbox EKO-25-2, which does not fit the cover from the gearbox of a truck.
The HP reducer is installed in the engine compartment of the vehicle. The liquid heater is installed in the rupture of the hose that goes to the stove. The copper pipe from the LPG kit that goes into the trunk must be replaced with a seamless high-pressure steel pipe from the truck's compressed gas equipment. Control over the operation of the HP reducer is carried out by the pressure gauge (16) (0-25 kg/cm2), which is installed in place of the reducer pressure sensor.
To determine the amount of filled gas and control the pressure in the cylinders, a high pressure gauge (1) (Fig. 1) (0-250 kg/cm2) is installed on the end cylinder. pressure from a home refueling device, or at a gas station - CNG filling station. For this, a filling fitting from a truck is used. To connect the cylinders to each other, connect the HP reducer, tees, only high-pressure seamless steel tubes (3) with an outer diameter of 10 mm and an inner diameter of 6 mm can be used.
To prevent damage from vibration and distortions, short parts of gas pipelines are bent in the form of rings with a diameter of 100 mm. In addition, the cylinders must be installed on a common frame in nests lined with rubber bands. The entire package must be pinned together to prevent cylinders from moving. Each brand of car has its own layout option.
On fig. 9 shows one of options. In addition, the design of a package of cylinders depends on the type of cylinders, their number, which ultimately determines the mileage.
The mileage depends on the amount of gas in the cylinders, the determination of which is difficult because at different temperatures air in the same volume includes a different amount of gas. For orientation, you can use a simplified conversion factor:
a) at a pressure in cylinders of 150 kg / cm2 - 1 liter of cylinder volume, equivalent to 0.3 liters of gasoline.
b) at a pressure in cylinders of 200 kg / cm2 - 1 liter of cylinder volume, equivalent to 0.4 liters of gasoline.
That is, if the average car consumption is 9 liters of gasoline per 100 km and the total volume of cylinders is 50 liters (for example), the mileage will be as follows:
a) at a pressure in cylinders of 150 kg/cm2; 50 * 0.3 = 15 liters of gasoline (15 * 100): 9 = 167 km
Now knowing this, you can choose the type and number of cylinders depending on the required mileage. You should not chase after a high mileage, because the weight increases, the volume of the cargo compartment decreases. It is better to have a basic set of cylinders for a run of 80-100 km and an additional one for long trips.
Specifically for passenger cars, our industry does not produce high-pressure cylinders. Therefore, it is necessary to use them from different fields of technology,
On fig. 7 shows the dimensions of the most common types of HP cylinders. Oxygen cylinders of non-standard reduced size may be suitable for our needs. Scuba tanks are great for scuba diving. Cylinders made of fiberglass, reinforced with steel wire winding, made of composite materials are produced. They are very light and strong and perfect for our needs, but scarce.
You can also use high-pressure aviation or tank cylinders. In extreme cases, a cylinder of the required size can be made from ordinary oxygen by cutting out the middle part. After that, the cylinder is welded by argon-arc welding, translucent with a gamma flaw detector, and subjected to a hydraulic test in a specialized organization. In artisanal conditions, it is strictly forbidden to do this.
After installing the valve cylinders, adapters, filling fitting are placed in a box (4) (fig. 9) made of soft tin, into which the fitting (3) and the service window (2) are soldered, which is installed on the seal. The design can be taken from cylinders for liquefied gas. A piece of rubber tube is put on the fitting and is led out of the body through the window for refueling the gas tank or another place.
On average, filling gas cylinders takes 1-1.5 hours. To reduce refueling time, two compressors can be paired. Truck owners can use 4 compressors. On fig. 10 shows the principal circuit diagram inclusion of a 3-phase electric motor in a single-phase network.
Voltage is supplied to the IM motor through circuit breaker Q1, magnetic starter MP. When the "start" button is pressed, the relay P1 is activated, which, with its contacts P1.2, supplies voltage to the MP starter coil and connects the starting capacitors Sp with contacts P1.1. In this case, the starter is activated and connects the motor and working capacitors Ср to the network. At the same time, the auxiliary contacts of the MP 1.1 starter are closed and the starter becomes self-locking. When the Start button is released, Sp is turned off. When the “Stop” button is pressed or when the motor thermal protection relay RT is activated, the circuit opens, the starter turns off, the engine turns off and the circuit returns to its original position. When connecting the motor windings with a triangle Ср=4800 (IHOM/U), where IHOM is the rated current of the motor, U is the mains voltage. Sp \u003d (2-3) Wed.
When storing the car in a garage, a tube is put on the fitting, which is brought out above the roof of the garage. With this design, you will be fully guaranteed against any gas leaks. Cylinders must be checked before use. operating pressure, volume, technical condition. The outer surface must be free of dents, cracks, deep scratches and corrosion. Near the neck of the VD is indicated:
- the date of the test and the date of the next test;
- type of heat treatment (N - normalization, W - hardening with tempering);
- operating pressure;
- trial hydraulic pressure (p225);
- actual weight, factory stamp,
To connect gas pipelines, special adapters are used (Fig. 8), which are screwed into the cylinder instead of a valve, lubricating the thread with red lead. Adapter tightening torque -45-50 kg/m (450-500) NM. This can be controlled with a special torque wrench, which can be borrowed from a car service station. When the valve or adapter is fully screwed in, 2-5 threads should remain on its threaded part. The size of the taper thread (fig. 8) depends on the types of cylinders.
High-pressure pipes have a gasketless nipple connection, which, when the union nut is tightened, abuts against the conical surface of the fitting and, when deformed, seals the junction. If you purchased old tubes, you need to cut off the end of the tube with the nipple and put on a new nipple, smearing it with red lead, and tighten the union nut. After carefully tightening all threaded connections, the filling valve opens, the filling device is connected and air is pumped in to half the working pressure, the connections are checked, and if there are no gaps, they are pumped up to full working pressure.
Air leaks must be eliminated after the pressure has been completely bled off. If there are no gaps, then the filling valve is opened and the air is completely released from the system and gas is pumped into the cylinder. After that, the flow valve is opened and gas is released to the HP reducer, its operation is checked.
To do this, using the fitting (13) (Fig. 1), set the gas pressure at the outlet to 10 kg / cm2, then purge the low-pressure system with gas until the air is completely removed, start the engine on gas and check the pressure at the outlet of the HP reducer. may fall a little. All work must be carried out outside the premises. After that, the operation of the safety valve of the gearbox is checked. To do this, smoothly tighten the fitting (13) (Fig. 1) and gradually increase the pressure at the outlet of the reducer until the valve operates. It should work at a pressure of 15-17 kg / cm2.
If the valve operates at a different pressure, loosen the locknut on the valve and adjust the response. After that, the tightness of the main valve is checked. To do this, the fitting (13) is completely unscrewed, while the gas must not enter the low pressure line. If the pressure slowly increases, then the valve seat is changed in the gearbox or handed over to the workshop. If everything is in order, make a test drive and check the low pressure reducer.
How to do this is well described in the instruction manual for liquefied gas equipment and there is no need to describe it. It should be borne in mind that when using a low pressure reducer from an liquefied gas jet, your car may slightly lose dynamism. To prevent this from happening, you can drill the jets in the gearbox by 1-2 tens, but then the mileage and efficiency will decrease. So the decision is yours.
Safety regulations for the operation of the vehicle and filling device.
You need to know that natural gas is lighter than air and rises, unlike liquefied gas, which spreads along the ground, fills all the cracks and cellars. Therefore, during operation, this feature must be taken into account.
Before each departure and return to the garage, after maintenance and repairs, a leak test must be carried out. gas system. Most available ways detection of gas leaks - this is odor control and washing with soapy water. If you smell gas while driving, you need to fix the problem. If you cannot eliminate the malfunction, it is necessary to release the gas from the cylinders into the atmosphere (in the absence of people nearby, open flames, other vehicles).
When the gearbox freezes and the engine starts in winter period to warm up, use hot water, the use of open fire is strictly prohibited! If the gas-balloon equipment catches fire, it is necessary to close the valves, turn off the filling system. To put out a fire, you need to have a carbon dioxide fire extinguisher on hand. In this case, it is necessary to water the cylinders with water in order to prevent an increase in pressure in them.
Once every three years it is necessary to check the high-pressure cylinders with a hydraulic test, once a year they must be submitted for inspection. It is strictly forbidden to attach structural elements to the surface of the cylinders by welding. When refueling a car, it is necessary to control the gas pressure at the inlet and outlet of the compressor, the temperature of the cylinders, and the pressure in the lubrication system. There must be no people in the car during refueling.
If gas leaks are detected, refueling must be carried out at following conditions: refuel only when the flow valve is closed, when refueling, do not stand near the refueling hose, do not tighten the nuts during refueling under pressure, do not knock metal objects on the parts of the refueling system. Disconnect the filling hose only after closing the filling valve. When the working pressure in the cylinders is reached, it is necessary to turn off the compressor engine, close the filling valve, close the valve at the compressor inlet.
In conclusion, I would like to say that the task was to give you a simplified, affordable and at the same time safe and workable design of the filling device, which can be assembled for a fairly a short time and receive moral and material pleasure from their work. At the same time, the article is educational in nature and the site is not responsible for possible consequences use of materials.
Gasoline prices are growing at such a pace that you do not have time to remember them, and more and more drivers are thinking about alternative types fuel. Alas, but high price electric vehicles does not yet allow mass transfer to them, the same applies to hydrogen fuel. Now the most effective way to save on refueling is to equip the car with gas-cylinder equipment () and use natural gas (methane) or liquefied gas (propane, butane) as fuel. Propane is obtained from oil refining, but methane is the same gas that we all use to cook food on gas stoves, it is supplied through pipes to most apartments and private houses. At the same time, if we compare prices for 1 cu. meter of methane at gas stations (about 15 rubles) and gas prices for the population (about 4 rubles), then a significant difference is visible. Therefore, many people have a reasonable question: is it possible to fill a car with LPG with ordinary household gas at home?
Indeed, such a possibility exists, but this does not mean that you can simply connect the hose from gas pipe to the car and fill it up. The fact is that in the cylinders installed on the car, the gas is under a pressure of 200 atmospheres, therefore, to pump it, you need a special compressor that can compress the gas to the required pressure and supply it to the cylinders. Such equipment exists, although it is mostly imported and it is not cheap - from 3,000 euros. But craftsmen have learned to adapt the AK-150S military compressor for these purposes, which is used on tanks, aircraft, infantry fighting vehicles and other military equipment. It will take from 4 to 10 hours to fully refuel the car with methane, depending on the type of compressor used, so this procedure is best done at night. By the way, the night the best time for refueling and for one more reason - fewer people use gas at this time, which means that the load that the compressor creates on the gas line will be less noticeable, because about 20 cubic meters of gas enters a 100-liter cylinder and in order to fill it, you need to pump out methane from 1 .3 km of a low-pressure network pipeline with a diameter of 140 mm. This can trigger the protection automatics at the gas distribution substation and the technical inspection system of the gas supply company will sooner or later reveal the cause of excessive gas consumption.
You don’t need to get any special permits for refueling with methane at home, but you shouldn’t meddle with gas workers with questions either - they will probably find something to dig into. It is clear that such a feint will not work in an apartment, this can only be done in a private house connected to a gas pipeline. And of course, for commercial purposes (i.e., to fill anyone who wants it for money), no one will allow you to open such a gas station at home. As an option - to cooperate with neighbors in the village, buy a compressor together and refuel in turn, then the costs will pay off very quickly. You just need to remember about safety. Speaking of costs - do not forget that the compressor consumes a lot of electricity, so the cost of refueling increases. However, some especially cunning fellow citizens even here manage to save money by winding and electric meter and gas, but that's a completely different topic. We invite you to watch a video on how home installations for filling household gas into a car work in Ukraine. By the way, gas prices for the population there are lower than in Russia ...