The cause of yellow plaque on the tile in the bathroom. Tile in the bathroom: than laundering a raid at home

Even a new ceramic tile after a few months of operation fits fastens, covered with ugly lime divorces, and the mold "blooms" in the seams. The cause of this kind of "microclimate" of the bathroom: high humidity in combination with poor ventilation. We will consider methods and means to be cleaned not only the surface itself, but also the seams between the tile with which there are a lot of problems.

Modern household chemicals helps to quickly wash the tile in the bathroom, but shopping products There is also back side»Operation: Sustainable chemical smell, strong allergens in the composition and, most often, considerable price. Therefore, we turn to simple, but tested by the people.

When working with caustic compositions and acids, always use household gloves. If you spray the tool, do not forget about the respirator, at worst, protect your mouth and nose with a handkerchief or groove. During the work, it is impossible to stay in a closed bathroom for a long time, especially if there is no fresh air inflow in it.

How to wash a smooth tile (tile)

1. Add a typical dishwashing gel to water (in any quantity, but with a minimum foam). Apply on the tile, leave at least 10 minutes, after the meat clean water.

2. Clean the tile and get rid of limescale It will help 9% vinegar (3 tbsp. spoons) diluted with water (1 liter) and meal of lemon halves. Hold the mixture on the surface of the tile for a few minutes, after the meat.

3. Suitable dining vinegar and for weak pollution: mix it with water (3 tbsp. Spoons per 1 liter), pour into the spoon and spray the walls. After a few minutes, wash the wet sponge, wipe the tile dry.

4. Medical or ethyl alcohol cleans well and disinfects the surface, giving shine. On 2 liters of water, take a quarter of a glass of alcohol, moisten a sponge in solution and gently wipe the blurred places.

5. To get rid of the "non-stop" of pollution use food lemonic acid (Sold in any grocery store). Fool the wet sponge into the crystals and carefully treat the tile surface with the substance.

Medical alcohol and table vinegar Use as less as possible. The components that are part of alcohol and vinegar contribute to the gradual destruction of the "grout" in the seams.

6. To return the cafée gloss, use ammonia (1 tbsp. Spoon alcohol on 2 liters of water). Hold the remedy on the surface of 10 minutes, then rinse with a damp sponge. Tile thoroughly wipe.

7. The melamine sponge shows well, which carefully cleans any surfaces and, not knowing, no additional means not required.

Melamine sponge do not need cleaning products

It is more convenient to wash the wall from top to bottom. But wipe - in the opposite direction. So well visible missed areas or divorces.

How to clean the matte tile

The surface of the matte ceramic tiles is more porous than that of glazed, and therefore use the means intended for cleaning the matte tiles, the maximum - "home" gentle formulations. The most common of them is the soap solution (effective during non-silic contaminants). As an option: Add to soapy foam The dishwashing detergent, but make sure that the composition does not have organic acids and fats, which negatively affect the susceptible structure of matte ceramics.

In order not to be scratching, use only soft sponges, and cleaning products should not contain abrasives. An exception - baking soda For point pollution. Neat circular motions stuff the soda into a dirty plot, after rinse with water.

For laundering matte tiles only soft sponges and means without abrasive substances are suitable

How to clean the seams between tiles

Do not use metal brushes for cleaning seams. The old toothbrush is best suited, but with a colorless (white) bristle - color can paint the surface.

1. And here will cope with 9% table vinegar. Mix it with water (equally), spray the composition on the seams. After the rummate and well dry the surface.

2. The oxygen bleach is also useful. Add water to it (in equal proportions), apply a mixture on the seams, leave for 10 minutes, then rinse with a soft sponge and wipe off the dryness with a rag.

3. Hydrogen peroxide will help effectively clean the seams between tiles in the bathroom not only from mold, but also from other contaminants, including lime bloom. Mix the substance with water (per 100 ml peroxide 200 ml of water) and process the grout to this non-slip solution.

4. If the seams are "running" and the mold layer is no longer cleaning with traditional methods, try to carefully rub the surface with sandpaper.

For drying seams and wipes dry tiles, buy napkins from microfiber: they are perfectly removed moisture and do not scratch the surface. Alternatively, use a terry towel.

Microfiber napkins are ideal for removing moisture from the grout between tiles

Prevention of mold appearance on tiles and seams

The following measures will help to avoid long-term and tedious cleaning:

Do not permanent high humidity In the bathroom: Keep track of the condition of hood and plumbing, more often ventilate the bathroom (especially after use).
Replace metal pipes On polypropylene - condensate does not accumulate on them.
Before finishing the walls, treat the surface with a special composition that prevents the appearance and reproduction of the fungus.
The joints, cracks, gaps, in which moisture accumulates in a small amount, treat the sealant.
Get rid of the habit of driving underwear in the bathroom.
In a timely manner, clean the shelves lime and mold, hooks, stands.

August 14, 2016
Specialization: finishing facades, interior decoration, construction of cottages, garages. Experience and gardener and gardener experience. There is also experience in repairing cars and motorcycles. Hobbies: the game is not a guitar and a lot more, to which there is not enough time :)

Rock on the surface of the bath is an inevitable phenomenon with which they have to face each mistress. It is usually not difficult to get rid of it, however, it is necessary to approle it competently, otherwise you risk getting rid of not only from sediments of salts and minerals, but also plumbing. Therefore, in this article, I will tell you how and what to wash the bath and other surfaces with the old ones, so as not to ruin the plumbing.

Where does Nizht come from

Immediately, I note that it is almost impossible to prevent the appearance of the plaque, since the main reason for its appearance is evaporation of water, which interacts with soap. Truth, water water Even by itself leaves the flare, since it contains a large number of mechanical particles and salts.

After water drying, all these minerals and other elements are deposited on the surface in the form of gray Nalea. If water is rich in iron, it can also paint the surface into a characteristic orange color . As a result, a snow-white bathroom for a very short term turns into an unsightly container "seroburomaline" color.

Of course, after each use, you can wipe the bath with a dry cloth. In this case, the flare you will not see soon. However, to keep track of all drops falling on the surface, it is impossible, so sooner or later to face the need to remove deposits will still have to.

There are currently on sale. There are many household chemicalswhich effectively cleanses the fall of both species. However, most of the compositions are made on the basis of acids, as a result of which they are very toxic and even capable of causeing a burn when entering the skin. Powder products are more eco-friendly, however, scratching the surface of plumbing, as a result of which it gradually loses its original attractive look.

Therefore, all sorts of "folk" funds are very relevant and in our time.

Methods for removing lime plates

First of all, consider how to clean the bath from a lime-type floor. To do this, you can take advantage of the following folk remedies:

Below I will tell you how to get rid of pollution by all these ways.

Method 1: Table Vinegar

The easiest way to clean the surface of plumbing is the use of a six-percent cutlery. It is possible to use it as follows:

pour undiluted vinegar into a tank with a pulverizer, for example, remaining from some cleaning agent;
then spray vinegar on the contaminated areas of the bath. For greater efficiency, on top you can "walk" with a brush, however, not very tough, so as not to scratch the coating;
after that, the surface must be left for half an hour or even an hour. At the same time, make sure that the surface does not have time to dry. As a rule, the composition has to be applied every 15 minutes;
after the specified time, you need to clean the surface with a brush;
if necessary, the procedure should be repeated;
at the end of the work, plumbing needs to rinse with water.

This method can be applied for tiles. The only thing before washing the tile in the bathroom from the plaque, wash it with soapy water to open access directly to lime.

If the flight accumulated in large numbers on the site near the drain hole, as it happens, plug the cork and pour a glass of vinegar in a bath, heated to a temperature of about 40 degrees. Vinegar will need to leave for the night, after which the pollution will certainly disappear.

Method 2: Lemon Acid

Lemon acid is a good alternative to vinegar. Its main advantage is the absence of unpleasant odor. Cleaning the surface with lemon acid is as follows:

dissolve a tablespoon of citric acid in a glass of water. Granules must be completely dissolved, otherwise you can scratch the bath surface;
using a sprayer or sponge, apply a solution into contaminated areas and wait 10-15 minutes;
after this time, plunge the sponge into the solution again and do it yourself with your hands the contaminated areas. As a result, the surface will be cleaned in your eyes;
In complete, the bath must be rinsed with water.

It must be said that citric acid perfectly removes the soapfile. Therefore, moistened in the solution with a sponge can be "walk" throughout the bath.

Method 3: Soda and washing powder

Another effective detergent can be made from the following components:

Used this means in the following way:

in hot water should be gradually pouring soda and powder;
now plunge the sponge into the solution and process them the contaminated area. The composition should be left on the surface for 10-15 minutes;
now pollution should be lined with the same sponge.

Choosing than laundering a tile in the bathroom from the fall, you can also stop on this lineup. He effectively copes with various species Pollution by different surfaces And even mold.

Method 4: Soda with vinegar

If you want to clean the surface of the bath from a limescale fast, efficiently and with minimal cost Forces, then use soda with vinegar. The instructions for the use of these means looks like this:

initially, the surface is soda with a solution of soda. For its manufacture, distribute three tablespoons of soda on a glass of water;
after that, apply not the surface of vinegar. The removal process will begin with chemical reactionwhich is accompanied by the formation of foam and hissing;
after half an hour, the treated surface must be washed with water;
if necessary, repeat the procedure again.

As a rule, after the first second time, the surface of the plumbing becomes perfect white.

Method 5: Summer Alcohol

The ammonia well cleans the surfaces from various contaminants to the "glitter". Therefore, is a favorite "grandmother" tool.

It is easy to work with it simple - moisten the rag in the ammonia and put it on a polluted area. After an hour, rinse the surface with cold water.

When working with the ammonic alcohol, provide high-quality air ventilation, as it has a sharp unpleasant.

Alternatively, the ammonia can use hydrogen peroxide. This composition destroys the collapse as a result of the separation of active oxygen in the process of chemical reaction.

Removal of yellow laid

So, with cleaning baths from lime deposits we figured out. Finally, I will tell you how and than laundering a yellow raid. To do this, you can use the following means:

Method 1: Bura and Lemon Juice

First of all, consider how to remove the yellow flare with the help of a bee of lemon juice, as this tool is checked for decades. It applies as follows:

prepare pasta out lemon juice and borants;
apply a paste on the yellow plot with a brush;
give paste to dry;
now wash the paste together with rust running water.

As a rule, rust leaves after the first application of the composition. However, if necessary, the procedure can be repeated.

Method 2: Homemade Pasta

To make a paste, you will need the following ingredients:

After mixing all the ingredients, they should be applied to rusty stain no more than 30 minutes. After this time, the paste must be washed with flowing water.

Method 3: Trinitrium phosphate and hydrogen peroxide

Trinatrium phosphate is an excellent degreasing agent. It can be purchased almost in any economic store. And if you add some hydrogen peroxide to it, it copes well with rust.

This composition is applied as follows:

four tablespoons of the trinodium phosphate are in line in three liters of water;
after that, pour into a solution with small portions of 50 g of hydrogen peroxide;
next, moisten the sponge in the resulting composition and rub a rusty spot;
when the stain becomes barely noticeable, apply to it a tool and leave for 10 minutes;
after the specified time, rinse the processed area large quantity water;
if necessary, repeat the procedure.

Method 4: Shanvlev

Simple enough and at the same time effective tool It is shanvlev. It needs to be diluted with water in proportion 1:10 and apply to a polluted area.

This means applies as follows:

shanvlev, apply a brush to a contaminated area;
then leave the composition for three hours;
after that, wipe the treated area with a sponge, moistened in warm water.

Method 5: hydrogen peroxide with ammonia alcohol

Finally, consider how to clean the bath with hydrogen peroxide with ammonia alcohol. This is done as follows:

in clean capacity, mix 150mg of the ammonia alcohol and 50mg hydrogen peroxide;
leave the solution for 10 minutes until the reaction is completed;
now you need to moisten a sponge in solution and apply to the yellowed area;
after 20 minutes, the remedy should be washed off with running water.

I must say that this method Commonly universal, so it can also be used to remove a lime-plane.

People often are interested in how to clean the mirror from the plaque. For these purposes, it is perfect for a dental powder that is frozen with a vet. In the same way, can be cleaned glass.

Here, in fact, all the ways of cleaning the bath from the plaque, which I wanted to tell you.

Output

Taking advantage of the above methods of cleaning the bath, you can remove any types of raids, and do not damage the surface. In addition, they provide some savings, as the price of all compositions is significantly lower than the cost. special Tools.

Additional information contains video in this article. If some points of the article caused your questions, ask them in the comments, and I will gladly answer you.

August 14, 2016.

If you want to express your gratitude, add clarification or objection to ask the author - add a comment or tell me thanks!

15297 0

We daily have to deal with mud in your house: wash the floors, dishes, wipe dust with a dust cloth ... But the bathroom, or rather, the facing is unlikely to make any mistress makes every day, and with the tile time with its appearance it does not make an eye at all. How to wash it, get rid of mold, disinfection - will tell this article.

Applied various methods How to clean the tile in the bathroom, both those who have already become folk and new types of modern cleaning products. Also, the separation goes to the types of tile contaminants, from here and cleaning different.

Safety above all!

When you take at home to clean the tile or remove the mold clusters, first of all, you should take care of personal protection against chemicals, as many of them can bring harm to health. To protect your hands, it is best to use dense latex gloves. And if necessary, apply protection for respiratory organs (respirator, gauze bandage).

After the end of the work, it is necessary to thoroughly wash your hands and face with warm water with soap. In order not to poison evaporation, Discover the doors in the bathroom, turn on exhaust ventilation - In general, ensure that you ventilate.

To prevent damage to your own property, do not use strong concentrated acids and alkali under undiluted. They can damage the facial layer of tiles, and it will be impossible to restore the appearance.

Home chemistry

Table vinegar. It is in every home, we usually use it in the kitchen. But it can well be applied in the bathroom for cleaning seams and tiles - both from the fall and from pathogens. To clean the seams, you can use the undiluted vinegar, and for the surface of the entire tile it is better to dissolve in the proportion of 1 to 10; If necessary, concentration can be enhanced. Clean the seams are conveniently an old toothbrush, and the rest of the surface you need to apply vinegar for 10-15 minutes, after which the rubbing with a rag, wash off with water.
Lemon acid. The means similar to its qualities with vinegar is only weaker. But it has such an important plus as a pleasant scent of citrus after the end of cleaning.
Chlorine, "White".It is known for ancient times with disinfecting properties and can wash the dirt and flare, even remove the spots of mold. It is worth knowing that the seams are bleached in the event that they are colored, or becomes lighter tint White. Therefore, before use, try to verify the undeveloped white slicer of the seam. To launder the lining in the bathroom, you need to apply chlorine and leave for 10 minutes, after which it was washed.
Summer. Used only in a divided form, as it has too sharp odor. 1-2 tablespoons are bred in 2-3 liters of water. It helps not only clean the tile, but also to return the gloss for the gloss! To do this, it is better to use a more concentrated solution of ammonic alcohol.

Soda. Also a proven cleaning agent, sometimes copes better than many specialized funds. It is possible to clean it like a raid, and not strongly rooted fungus. For use, it is best to dissolve it with water to the state of sour cream. It is possible to use it to use it with the addition of hydrogen peroxide - then the microbes together with the fungus and mold will be destroyed. It is worth only to know that it is not worth lying soda with special zeal, especially in glossy tiles, as the soda contains small abrasives. After applying soda, it is necessary to thoroughly wash and wipe the treated surface.
Bura. It is used to remove fungus and mold. Does not cause allergies. Divorce with water 1 to 10 and clean the brush. You do not need to wash after use.
Copper vigor. The fungus can be cleaned with a sipop, only it is toxic and it is worth working in well-ventilated rooms. Divorce 1 to 10 and applied to the affected areas with a brush, for several hours. After that, it is thoroughly clean and dried.

Modern chemicals

Today's industry fully satisfies our requirements in bathroom cleaning. The consistency of them are diverse: gels, dry agents; Sprayers of liquid solutions are used. At home, strong alkalis and acid are available. Domasetos, Sanoks, Sif, "toilet duckling" - all these mixes, in accordance with its specific purpose, allow you to cope with most stains in the bathroom.

Brown, black or bluish spots in the corners of the room or on the seams between the tiles, testify to the fungus, and you can clean them with the help of special means. When combating fungus, it is necessary to check the effectiveness of ventilation and get rid of the places of constant dampness. To secure the result, it is recommended to thoroughly dry the surface with a construction hairdryer.

To remove lime plates, the toilet detergent is suitable, cleaning gas plates And ovens. If this does not require the instruction, you should avoid drying chemicals, since it is difficult to remove the dried agent, while you can spoil the appearance of the facing. To prevent possible damage to the tile, it is desirable to try to treat the site first at the most imperceptible place, and after successful experience to do the entire surface.

External view The tile is best supported by its regular cleaning, it is relevant and for the prevention of mold.

It is necessary to distinguish stains and pollution, wash them with appropriate means. If you wash the ceramics to the tool from lime and soap plates, it will not protect against fungus and mold.

Clean and maintain the gloss can also be used to clean the glass and mirrors.

Melamine Sponge is a practically universal cleaning agent

Melamine sponge.

A new type of cleaning products and tools at the same time. They make such sponges by swelling the melamine resin, clean such a sponge can any surface and contamination. Allows simple and accessible to clean the facing. For this, it is enough just to moisten a sponge with water and wipe the surface, and without special effortsThe more tenderly wash, the better the effect will be. To launder especially complex stains, you can use detergents. After processing, rinse and wipe the tile with a dry cloth.

Steam generator.

Also means of prevention. It is capable of cleaning the mud that is washed with water, but it still makes disinfection of the surface of the tile.

Steam generator - a great remedy for cleaning and disinfection of a bathroom, toilet and tile surface

With unsuccessful attempts to clean the seams, perhaps better decision It will be to replace completely grout. And to prevent such situations when the fungus eats the entire seam, we need to wash the seams in time with the substances against mold and fungus.

Clean and comfort your home!

In the fight against a lime bloom in the bathroom, the most important thing is to choose the right tactics, otherwise it is possible to say goodbye not only with sediments of salts and minerals, of which there are actually plates, but also with plumbing. After all, covers that manufacturers are used today are different types.

What is better not to clean the baths?

Earlier special choice There were no baths - they were all out of cast iron with an enameled coating. Such baths and today are in great demand. but modern world Plumbers are more diverse: steel, acrylic appeared and even you can find baths from durable plastic.

It is important not only to know how to remove the lime bloom in the bathroom, but what to do it better - after all, each of the baths requires its care. The incorrectly chosen drug will spoil the coating and will lead the bath in an unsightly kind of several cleaning.

First, it is impossible to clean the bath with a metal scraper or brush - they scratch any coating, which leads to the formation of cracks;
Secondly, it is impossible to use acid-containing cleaning products, especially those that we use to clean the limestone in the toilet (by the way, we wrote separately about the toilet cleaning agents) - they energize the enamel, not to mention acrylic;
Thirdly, the enameled and cast-iron bath is cleaned 1 time per week, and acrylic less often - 1 time in 2 weeks.

If you follow these rules, you will not need to look for ways to clear a strongly contaminated bath from a limescale. Now let's understand in more detail, the better to remove the limestick in the bathroom of different species.

It is quite simple to understand here any powder contains abrasive substances. Cleaning powders can be used to remove lime plates from cast iron and enameled baths, and here for acrylic and metal surfaces It is better to choose a liquid means in the form of a gel - such a consistency allows you to evenly distribute the tool over the surface and does not create an aggressive action.

And now attention! Liquid means To remove a lime flush, you do not need to rub - they are applied to the surface, left at a certain time and simply wash off with water.

What to clean enamel and cast-iron bath?

Remove the limestone raid from the cast-iron and enamel bath is easy, provided that your bath is not restored, and the coating has been preserved factory. Selecting the product for cleaning iron and enameled baths, as well as for metal cranes and soul, read what is part of:

Inexpensive means do not contain anti-corrosion inhibitors - substances that do not damage the surface, especially if you brush metal cranes. Cleaning the bath and plumbing in the bathroom with a cheap tool, you will be satisfied with the visible result, but the fact that, together with the fallow, you removed the coating from the surface of the bath and cranes, will become noticeable with time. Inhibitors act exclusively on the lime flaka and do not damage the surface. Therefore, choosing a means for cleansing a limescale in the bathroom, look for a string in the line - Anticorrosive inhibitors.
If noticed in the composition of sulfur or nitric acid, Put in the direction of this tool - this is a "heavy" artillery for cranes and baths. Funds with these acids It is better to use to clean the toilet or for the launched crane and bath options - the so-called "disposable attack". For frequent cleaning, there will be enough tools based on surfactant , Which, falling into the water, split and act on problem areas.

Acrylic baths: care features

Acrylic baths appeared relatively recently and are very popular with consumers. The surface of the baths of this species is smooth and washes easily, so to clean the limestick with acrylic bathIt is enough to use a liquid universal means in which the aggressive elements are not contained: ammonia, acetone, chloric - these substances may damage acrylic.

If you regularly monitor the cleanliness of the bath - rinse after use with warm water and wipe the microfiber with a cloth, then with a thorough cleaning it will be enough to wash the bath with a cloth, pre-leaving the selected detergent on its surface.

Today it is not difficult to choose a remedy for removing a lime departure to choose for an acrylic bath - most of them are perfectly coping with their task.

For those who are looking for how to remove a strong limestone with an acrylic bath, we recommend using folk tips:

Fill the bath with cool water (20 - 25 degrees);
Pour into the water 0.5 liters of vinegar (7%) or pour a plate of citric acid;
Leave everything overnight or day;
Drain the water and rinse the bath with clean water, then wipe dry.

Diluted with water vinegar can be wiped with cranes and bath to remove the flare.
And you can also add a bit of vinegar into water for swimming - an easy acid medium will soften water and prevent the waterstop of the walls on the walls.

From a strong waterstock flooring, you can get rid of folk remedies:

Mix cleaning powder with water - make a crawler, add a tablespoon of whiteness and 2 tbsp. vinegar. Such a tool will help remove lime flask.
Help Clear lime collapse will help the ammonia alcohol, divorced in water, which is applied to the walls of the bath and wash off after a few minutes.
It will also help to cope with a water stone of lemon juice, which rubbed the bath and flush after 10 minutes.
Flip will go, if gratened the walls enamelled or cast-iron bath Vinegar with salt. For acrylic, this method is not suitable.

For disinfection of the bath, it is enough to fill the top bath with water to which you add 50 - 100 g of whiteness - it will help to disinfect and whiten the bath.

As you can see ways, how to clean the lime bloom in the bathroom, a lot. What to choose is better - ready tool or take advantage folk recipe, decide for yourself and share your advice with us.

Simple, not time-consuming and not costly laundering a ceramic (tile) tile to shine. The concentrated citric acid solution can cope with a resistant lime bloom on the surface of any tile in the bathroom.

An indisputable fact is that the tile (ceramic tile) is the best and perhaps the most popular finishing material to date. And it is quite justified. We will not list its advantages. But here are small nuances when using all the favorite ceramics still have. In particular, this concerns our tile content clean. Not depending on the type of surface of the tile (glossy or matte) the quality of its manufacture, and not looking at the old one or new ... Most of all this question concerns the bathroom.

Daily splashes, drops and water flows are left persistent, multi-layer lime flaka, which is simply not washed off.

What to wash ceramic tiles So that she is glitter?

Typically, the procedure for laundering the tile in the bathroom from the plaque is very time-consuming and ineffective. Laying a short timeYou will need strong chemical To remove a layer of deposited salts. Such funds are usually scary with caustic, poisonous and often very expensive.

We offer an easy way to wash the tile from a limescale or more than science. It does not require great physical effort, does not entail expensive financial investments. We will wash the ceramic tile with a concentrated solution of citric acid.

We need ordinary lemon acid (which is sold at any store), sprayer for water and brush or sponge.

Often, in lemon acid cleaning advice, it is recommended to rub the contaminated surface with acid crystals (not divoridated in water). We do not advise this. Everything can be done much easier, safer and more convenient. Our method will relieve you from the need to rub, or rub anything into the clean surface to exhaust. We propose to spray our tool with a sprayer.

For a start, dissolve acid crystals in warm water to a saturated solution - in proportions 1 to 2 (100 grams of acids per 200 grams of water)

Flip finished solution In the sprayer.

And then we simply wet (spray) on the surface of the tile.

For safety with a solution with a solution of an acid: Put the rubber gloves, do not close the door of the bathroom during operation, avoid entering the skin and mucous membrane.

For greater grip - it is desirable to confuse the solution on the surface with a brush or sponge.

After that, it is necessary to wait until the solution reacts (interacts) with a limescale.

As drying, white divorces are formed on our tile.

But you should not be afraid - this is a good sign. This means that our remedy has worked and coped with our pollution and the result is achieved.

Now you can wash off by water.

White divorces are washed with the soul and the same sponge or brush. If after time white flag It will again seem on the surface it is not scary. It is simply not to the end, the washed solution of acid adopted its task, and it is simply necessary to rinse the surface with water again.

After that, yours tile Blinder as new. And if you do not bother - repeat the procedure again and achieve the desired result.

Pros of this method:

The method is absolutely environmentally friendly.
A citric acid solution is not harmful (it is used even for cooking).
Ceramic (tile) tile does not deteriorate from the effects of citric acid solution. This is not an abrasive material, and it does not damage the surface of ceramics.
It is cheap and accessible to everyone.
You do not need to make great physical efforts, just spattered the surface with the prepared solution and wait for the result.
Wash the surface in this way do not have often. It remains clean for quite a long time.

Disadvantages:

Only one - you, for some reason, do not like citric acid (you do not like its smell, allergic to this product, etc. etc.).

We will be glad if our method helped you in a tireless fight for cleanliness!