If your washing machine is leaking, you need to install a leak protector. We will consider all the options, and also talk about what Aquastop is in a washing machine and what programs are already installed to prevent leakage.

Faced with such a nuisance, it is necessary to act quickly. If the leak is not fixed on time, you risk not only equipment breakdown, but also the repair of the premises - yours or the neighbors below.

There are many reasons that lead to a leak:

• the use of low-quality detergents;
• non-compliance with user instructions;
• manufacturing defects;
• damage to seals and pipes, etc.

The first thing to do when leaking is to stop the water and drain it from the tank. Only by shutting off the water supply valve and turning off the washer from the network, you can proceed to the inspection - to determine the location of the leak.

Reason 1. Hose

You need to conduct a thorough inspection of the water supply hose. As a tester, use the usual toilet paper: with its help you can find all the damage and leaks.

If it was the hose that was the cause, then the malfunction can be eliminated quickly and practically without cost:

1. If a break is found where the inlet hose connects to the machine body, replace the gasket. At the same time, you can check the filter mesh for blockage.
2. In case of mechanical damage, seal the puncture with a patch using waterproof glue. In this case, electrical tape will not interfere.

Important! Most the right way troubleshooting - not repairing the hose, but replacing it.

Reason 2. Powder receiver

When water starts to flow in the machine immediately after it arrives, the reason may be the dispenser - the compartment for washing powder. For example, undissolved grains of powder can get stuck in it or sediment from dirty water can form.

In such a situation, proceed as follows:

1. Pull out the dispenser and thoroughly clean all corners with an old toothbrush.
2. Put the dispenser in place.
3. Start the testing machine.

Water should not flow under high pressure, so if necessary, screw on the water supply valve.

Reason 3. Branch pipes

It is possible that the inlet valve pipes in your washer are damaged. In this situation, you will have to remove upper part machines and replace parts. If the problem lies in the pipes for collecting water, it is not necessary to change the part, it is enough to seal it well.

Important! The reason for the failure of nozzles is the austerity of manufacturers. Poor-quality products quickly lead to equipment failure.

Reason 4. Rubber cuff

Having found a water leak from the door, you can be sure that the rubber cuff designed to seal the door has been damaged.

Everything is very simple here: disassemble the door and remove the seal, seal it with a patch. With a large gap, it is recommended to replace the seal with a new cuff.

Reason 5. Drum

With frequent washing of shoes, clothes with metal products drum may be damaged. If you find this, contact a specialist who will replace the drum.

If you want to save money and try, read our instructions.

Leak protection options

Many budget washers and mid-range machines do not provide protection against water leakage. What can happen to a machine that lacks protection?

In such models, the flow of water comes from the water supply through a flexible hose for the washing machine. Often they do not have a bottom, or it is covered plastic panel. When the inlet hose breaks, water collects and then flows to the floor.

In order not to make a flood, experts advise turning off the valve after turning off the washer. You can also install another protective system on your own using inlet hoses with valves.

But more expensive cars attract many buyers with protection installed from the factory. You can safely purchase the latest models of cars from brands such as Asco, Ariston, Bosch, Zanussi, Siemens, Electrolux, AEG, Miele.

Partial leak protection

Let's understand how partial protection works.

Models providing such protection have a special pallet, inside of which a float with an electric switch is installed. When a leak occurs, water collects in the pan, when it reaches a certain limit, the float rises, affecting the switch.

The plus is that in the event of a leak, the washing machine automatically stops working, the drainage pump drains the water.

Important! You will know about the leak by the error code on the display. For example, E1 code will appear in the ElG washing machine, a in brand model.

If there is water in the pan of the washing machine, it is necessary to drain it, and then carefully inspect the equipment, finding the cause of the malfunction.

A washing machine with partial protection is a model in which operation is provided only when water flows into the appliance. In the event of a hose rupture, a flood is guaranteed anywhere. In such a situation, it is best for you to purchase inlet hoses with valves.

Hose types:

1. The hose, complete with a block with a peephole, is connected to the water supply. Inside the block is a plunger, which is held by a spring.
   When the hose breaks, water enters, the spring weakens, and the plunger prevents water from leaking. The peephole turns red, warning of danger.
   Spring-loaded hose protection guarantees quick response, so you can prevent flooding and damage to the washer.

Important! Such a hose has one significant drawback - after it is activated and notifies of a leak, it will have to be dismantled.

1. This hose, according to the principle of operation, is identical to the first type, the only difference is that several magnets are installed inside the block, turned to each other. Due to this, the plunger is held before the water flows into the protective block.
   This hose, like the previous one, must be replaced immediately after activation.
2. Hose with solenoid safety valve. As long as the washer's power cord is not connected to the mains, the plunger shuts off the water supply. When the machine is turned on, the valve opens.

Menalux protection is the installation of a special hose that guarantees reliability and prevents leakage.

Full protection against leaks - a guarantee of reliability and stable operation

In models equipped with full protection, the Aquastop system is provided with the following elements:

• pallet;
• float;
• hose with solenoid valve.

The principle of operation of the system is to operate when:

• tank leakage;
• rupture of pipes;
• high level of foam formation, its exit to the outside.

In addition, an emergency operation occurs if the main and safety valve do not work. You can turn off "Aquastop" by installing a valve that automatically stops the water supply.

Conclusion: how to protect the car from leakage

If you are concerned about the problem of water leakage, it is recommended to purchase more expensive models of washing machines, which provide for partial or full protection from overflow.

Only high quality machines positive feedback cope with washing clothes and serve you long years no major damage or leaks.

You were washing and suddenly noticed water on the floor. Perhaps your washer leaks constantly, but little by little. Or maybe there was a real disaster, and the machine suddenly flooded the entire floor. Both cases indicate a leak in the water circulation system.

Owners of modern washing machines equipped with protective mechanisms are more fortunate. If any hose or connection is damaged, the leakage protection is triggered. It blocks the water and prevents the flood. But if protective system worked, it means that there is a leak, and it must be found and fixed. Let's figure out how to do it right.

Why is the machine leaking?

Water leaks when the system is depressurized and clogged. Main causes of leaks:

• Blockage of the dispenser hopper.
• Damage to hoses and pipes for draining and filling water.
• Drain pump failure.
• Crack, breakdown of the tank.
• Manhole cuff damage.
• Deterioration of the tank seal.
• Loose connections between hoses and pipes.

Any of these faults can occur in washing machines of all brands. But each model has its own weak spots. Knowing their specifics, it is easier to find a leak. Therefore, masters with experience cope with the diagnosis much faster than non-specialists.

We save the car and the apartment: the first steps when a leak is detected

If you notice a puddle, stop the flood:

1. First of all, unplug the washer from the mains. Be careful! Do not step into spilled water - risk of electric shock. If you can reach the socket from a dry place, unplug it. Otherwise, turn off the electricity at the panel.
2. Shut off the water. For such cases between water pipe and a tap must be installed with the inlet hose of the washer. Overlap it. If the machine was connected incorrectly, and there is no separate tap to it, turn off the water throughout the apartment in the plumbing cabinet.
3. Remove the laundry from the drum. The machine did not have time to finish washing, and the tank is full of water? Drain it through the drain filter. It is located at the bottom of the case, on the front panel. Do not forget to substitute a basin under the drain so as not to increase the scale of the flood.

After that, you can remove the puddle from the floor and look for a malfunction.

We determine the place of the leak: first we inspect everything from the outside ...

Before sounding the alarm and calling the wizard, check everything around the washing machine. Maybe it's not her problem at all. Water, sewer or heating pipe next to the washer. If the "foreign" communications are intact, go to the typewriter:

1. Check the connection points for the inlet and drain hoses. The water is coming from there? Unscrew the hose and screw it on tightly again. Sometimes this does not help, and the leak occurs again. Then the gasket needs to be replaced. You can also treat the joint with sealant before screwing.
2. Now inspect the hoses themselves. They fray when kinked and improperly installed. Particularly vulnerable plastic drain hose. If damage is found, replace it with a new one. It's easy to do, you can do it yourself. The main thing is to buy a quality hose, best of all - the original one, from the manufacturer of the washer. But if the damage happened due to improper connection of the machine, it is still advisable to call the wizard as soon as possible and connect it correctly. Otherwise, the new hose will not last long.

Now is the time to call the master. And if you want to try your hand at repair, follow the further recommendations.

... Then we look for a leak near the hatch and under the top cover

Are the hoses okay? Then take a closer look at the machine itself. It is necessary to visually determine where the water is flowing from.

1. Carefully check the cuff of the hatch. Water can flow right from under it, along the front wall of the case - this is clearly visible. But when damaged inner part cuffs, a puddle will be under the machine. Therefore, even if a stream does not flow from the hatch, the cuff must still be carefully examined. Found damage? The best option- replace the damaged part with a new one. But if you really need to delay the repair time, try sealing the cuff and turning it so that the sealed place is at the top of the hatch. Remember that such gluing is a temporary measure, it will last only a couple of months.
2. Examine the dispenser hopper. washing powder does not always dissolve without residue and can clog its channels. characteristic feature such a blockage - water leaks from under the dispenser cover. If you notice them, remove the dispenser and thoroughly wash all its cavities and openings. Install the item in place.

The dispenser is clean, but smudges appear from under the lid on the next wash? So the problem is in the intake valve. It gives too much water pressure. Try to reduce the pressure a little. If this does not help, remove the top cover and inspect the inlet valve and pipes leading from it to the metering hopper.

These pipes often wear out and start to leak. Their damage is clearly visible. If the pipes are intact and their joints are tight, then the inlet valve has broken. Both the valve and pipes must be replaced.

At the end, we check the washer inside

Even if until now you have carried out independent diagnostics, it is better to entrust further searches to the master. Here you will need to disassemble the body of the washing machine. It remains to check only the tank and the drain pump. The tank has several weak points:

• Fill pipe. It is usually glued to the tank itself. If the bonding point is depressurized, you need to detach the part, clean it, dry it and glue it again.
• Stuffing box. It gradually wears out and stops retaining moisture. Then the smudges can be seen on the tank under the stuffing box. The seal must be replaced.
• The body, that is, the tank itself. It can be damaged by inept repair, strong impact, etc. Also, the walls of the tank wear out over time - steel rusts, plastic ones become brittle and crack. Unfortunately, a replacement is not possible here. You have to buy a new washer.
• Drain pipe. It is located between the tank body and the drain pump. When damage to the nozzle is visible, replace it. If there are no cracks, check the attachment points. Clamps often loosen here. They should be tightened, previously smeared with sealant.

After the tank, inspect the drain pump. Perhaps the sealing cuff has worn out in it. It is very difficult to replace it, so it is worth changing the entire pump at once.

Attention! Whatever the extent of the leak, its cause must be identified and repaired as soon as possible. Otherwise, "excess" moisture will quickly disable the electrical components of the washing machine and cause corrosion of steel elements.

Even if it flows “somewhere below”, the water will still evaporate inside the case, and the condensate will settle on all parts, including the very top ones. The consequence may be the breakdown of expensive components, such as an electronic module or engine. Therefore, do not postpone the call of the master - the sooner you make repairs, the cheaper it will cost you.

How to choose a washing machine?

The reason for writing this article was the frequent and recurring questions that users of washing machines usually ask our masters. And this is quite understandable, because the master knows everything about washing machines firsthand. We will give the interpretation of these questions and the answers given by professionals. Among all this, you can emphasize for yourself useful information, which will help you when choosing a washing machine.

For greater clarity, we have presented both types of automatic washing machines (hereinafter referred to as CM) - these are washing machines with frontal and vertical loading of laundry.
Both those and other CMs are approximately the same in all properties and qualities. Let's compare them.

CM front loading

Front loading washing machines They are more practical and usually slightly cheaper than vertical machines of the same group, and the cost of repairing the washing machine (if necessary) will be lower than that of top-loading machines, since vertical washing machines are a bit more difficult to maintain than front-loaded ones. The front SMs have a transparent viewing glass hatch, which more than once allowed many users to see and save their driver's license, money, plastic cards, passport and much more, which they accidentally forgot to remove from things before washing. Rubber compressor hatch (hatch cuff) of the frontal SM, does not break as often as it would seem to many. Damage to the cuff of the hatch occurs mainly due to careless handling. The fact that the drum of a front-loading washing machine has one mounting axis is in no way inferior in strength to a top-loading washing machine with two axles. For those who have little space in the apartment, a big plus of frontal washing machines is that the SM can be used as a nightstand, put some things on it. And in a top-loading CM, the top cover must always be ajar to avoid the appearance of mold fungus and therefore it will not work to use the CM as a bedside table.

Top loading washing machines Vertical CMs are usually more expensive than frontal CMs. This is due to the design features of vertical machines, because the process of assembling them is a little more complicated. The fact that in a vertical machine, drum bearings are located on both sides, does not give any advantages. Moreover, in such a design, it is more difficult to achieve coaxiality of the two axes of the drum. Due to the fact that the drum of vertical washing machines has flaps for loading laundry, one part of the drum becomes heavier and therefore it becomes necessary to balance it. Unfortunately, not all manufacturers perfectly balance the drum, which sometimes affects the increased vibration of the washing machine during its operation. It is worth mentioning a specific and unpleasant malfunction of vertical machines - this is the spontaneous opening of the drum flaps during operation, which sometimes leads to a fatal malfunction of the apparatus. Vertical CMs are good in that the working space and the area occupied by them are smaller (compared to full-size frontal machines), and the design of some vertical SMs allows, if necessary, to open the drum at any stage of the wash to remove or load the laundry, while not changing the course of the program.

CM top loading

In general, as we said, both types of washing machines are almost the same in all properties and qualities. Each type of washing machine load has its pros and cons, so choose the type of machine that suits you and is most convenient for you.

The world's first wall-mounted washing machine "Daewoo"

Frontal washing machines. In height and width, front-facing washing machines are almost the same, but the loading depth is divided into: full-size (60-65 cm), narrow (40-45 cm) and ultra-narrow (up to 32 cm). There are a number of washing machines that have a compact design, which allows such machines to be installed under special sinks. As a rule, ultra-narrow and compact models of washing machines have a maximum load of 3-3.5 kg of dry laundry. Vertical washing machines. All top-loading machines have almost standard sizes(except CM Asko 412 compact). SM must be selected for a specific location, for the planned load and for the preference of the owner. Functionality All automatic washing machines are the same. It must be borne in mind that the larger the one-time load, the more laundry it will wash over the entire time of its operation. Speaking of compact washing machines On November 21, 2012, specialists from the Russian office of the South Korean company Daewoo Electronics presented the world's first wall-mounted washing machine DWD-CV701PC. The weight of the washing machine is only 16 kg, the maximum load of laundry is 3 kg.

Do not confuse a tank with a drum! Drums - all washing machines (with the exception of some Asian brands) are made of stainless steel. But the material of the tank is different. Today, SMs have steel (stainless) and plastic tanks (they have different brand names, such as "Carboran" from Electrolux), and in the early days of washing machines, tanks were made of enameled steel. The general trend is that there are more and more cars with plastic tanks. Asian SM manufacturers don't make stainless tanks at all. Yes, and in Europe they are mainly made only by MIELE and ASKO, other companies too, but the share of such tanks in their products is small. Plastic tanks are good because the heated water during washing keeps the temperature longer, and therefore the energy consumption is reduced. plastic tanks well absorb noise, both inside and outside. The disadvantage of plastic tanks is fire resistance and impact resistance. In general, if nothing bad happens to the washing machine, then you will not understand why you need a stainless steel tank.

What is a silent washing machine?

A silent washing machine is distinguished not only by the presence of inscriptions and stickers on the body that speak of noiselessness. This class of washing machines has, first of all, sound insulation, i.e. the inside of the case is pasted over with thick soundproofing material. Along with this, special three-phase asynchronous motors drum drives, in which the noise level is an order of magnitude lower than that of standard collector motors. As you understand, you have to pay for such silent comfort, which inevitably affects the cost of the washing machine.

If you do not have the time or opportunity to dry your laundry naturally, then the washer-dryer the best solution For you. This SM combines all the functions of an automatic washing machine and has an additional unit for drying clothes with a stream of heated air. However, it should be borne in mind that such a washer-dryer can only dry half of the clothes from the maximum load of the drum, and drying can take about 2 hours (sometimes much more). But if possible, it is better to buy a separate dryer. By the way, it does not require a connection (only a power outlet). Such a machine can dry all the laundry washed in CM at a time. Modern dryers and washer-dryers, thanks to the electronic control system, finish drying the laundry on the signal of the residual moisture sensor, and not on the timer (as was the case in most washer-dryers of earlier years of production) - thus eliminating the risk of overdrying the laundry.

What spin speed is best?

Everything is simple and clear here, the higher the spin speed, the drier the laundry you get after washing, but also the higher the price of the washing machine. Whether you need increased speed and what residual moisture content of the laundry suits you, it's up to you. A typical washing machine has a speed of up to 1200 per minute. There are machines, such as ASKO, with a drum rotation speed of 1800 and even 2000 rpm. Keep in mind that for small-sized CM models (Candy, Electrolux. Zanussi, Euronova, Eurosoba) at the same spin speed, the laundry will be less dry. This is due to the small drum radius of compact models.

In description specifications Some washing machines, you can find the function of leakage protection. This is a very useful feature that emergency in the washing machine, help you avoid water leakage and prevent flooding. The leak protection system is called by different manufacturers in different ways: Aqua stop, Aqua safe, Aqua alarm. Leak protection is a complex technical devices provided by the manufacturer. This system is not installed in all brands and models of washing machines. Therefore, if you have the opportunity to purchase a washing machine with leakage protection, then you will not regret it.

What is the cost of a washing machine?

average cost a good washing machine as of 2012, approximately 17,000-20,000 rubles. There are of course washing machines and half the price. Are they worth buying? You need to decide based on the possibilities of your budget. But keep in mind that in general, the ratio of price and quality are directly dependent, the more expensive, the more reliable and better. Buying a cheap washing machine does not always help to save money, since the resource of such machines is less and you may have to repair it more often, or buy a new SM again. For some consumers, expensive and so-called elite equipment of such brands as: Miele, AEG, Kuppersbusch, Gaggenau, Neff - is an indispensable attribute emphasizing their status and they fundamentally do not buy cheap equipment. The cost of some washing machines of such brands can reach up to 250,000 rubles, and they already belong to a number of professional appliances. If an expensive washing machine won't break down (high-quality SMAs break less often), then it will seem to you that such machines are better than cheap ones. But are you ready to pay for the repair of an expensive washing machine as much as a new, inexpensive SM costs? It seems that everyone should find the answer to this question himself.

Which brand of washing machine should you choose?

Today, the situation in the household appliances market is changing, unfortunately not quite in better side. Manufacturers have become smarter and are doing everything to increase the sales of their equipment and accessories, so the resource of washing machines of most well-known brands has become lower. When choosing a washing machine, pay attention to the country of origin. Today, the so-called "clones" of European and Asian manufacturers are assembled at Russian factories. On the territory of Russia there are factories for the assembly of washing machines of such brands as: Ariston and Indesit (Lipetsk), Candy (Kirov), Whirpool and Vestel (Aleksandrov), Zanussi (St. Petersburg). These washing machines are inexpensive, but they are not of the highest quality.
In the table, we will give a hierarchy of the most famous brands by class steps:

Class step	Trademarks (their affiliation to concerns is indicated in brackets)
Top	Miele, Asko, Neff (Bosch), Gaggenau (Bosch), Kuppersbusch, AEG (Electrolux)
Top middle	Electrolux, Bosch, Siemens (Bosch), Brandt, Gorenje, Whirlpool
bottom middle	Zanussi (Electrolux), Candy, Ariston and Indesit (Indesit company), Ardo,Beko,Samsung,LG,Hansa
Bottom	Russian and Chinese "clones" of European and Asian manufacturers

This table will help you a little to orientate when choosing trademark washing machine.


We do not cooperate with trade organizations and will not engage in their advertising, but will give only a few valuable tips:
1. Buy equipment only in trusted, large and reliable stores;
2.Be vigilant! Always check the goods, at least for the presence of external damage and flaws, and also check the complete set of accessories supplied with the washing machine, check the availability of the warranty service book (it is even better to check the serial numbers of the warranty book with the number on the nameplate of the washing machine, they must match);
3. Be careful when buying a washing machine through distance selling stores, the so-called online stores. Take advantage of large online stores that have been on the market for a long time.
4. Do not purchase equipment from sellers who are mobile and do not have a permanent outlet;
5. Always keep sales receipts and cash receipts, and for the first 14 days, keep the packaging of the washing machine. According to the law of "protection of consumer rights" - this will help you exchange or return low-quality, defective, equipment that does not suit you within the period established by law.

Users of household appliances based on the use of water hear these phrases all the time: in specialized stores, many sellers quite often insert these words into their speech when explaining the merits of the home appliances they sell. What is called the Aquastop system, how is it used for active protection dishwasher, what it consists of and how to replace it yourself - we will try to answer all these questions in the article.

In world practice, any leakage protection is called Aqua-Stop or Aqua-Control. In principle, this is an ordinary water supply hose to household appliances, only enclosed in a special protective casing with a device that shuts off the water in case of unforeseen circumstances: a rupture of the hose, its leakage due to a crack, etc. Thus, the built-in protection system protects you from an unwanted flood. Its task is to immediately turn off the water supply to household appliances, dishwasher or laundry assistant to prevent water from dripping onto the floor.

Many homeowners do not even realize that the pressure in the plumbing system is quite high, and water hammer - a sudden increase in internal pressure - occurs frequently. Without reliable system hose protection is just not enough.

The standard Aquastop system consists of the following main parts:

• block of mechanical or electromagnetic valves;
• water inlet hose to the device;
• pallet;
• float;
• security wire;
• water release button.

Aquastop device: A - Solenoid valve, C - inlet hose B - control cable D - Leaks (water hoses)

All modern household appliances that use water are protected from unwanted leaks even during the manufacturing process. Each manufacturer wants users to buy only its model, therefore, in addition to the inlet hose, they supply their products with special pallets with electromechanical devices.

The whole system works smoothly and quite efficiently:

1. Solenoid or mechanical valves (1) are mounted in the water supply hose (2).
2. When the equipment is connected to the mains, then on safety valve voltage is applied, it opens, and the working valve is still closed.
3. If the user presses the start button and the machine starts the cycle, then working valve opens.
4. In the event of a leak, all water enters the sump (3), where its level is monitored float control(4). If the water level rises, the contacts open. The safety wire (5) is designed to cut off the power going to a similar valve, the power supply is interrupted - the valve shuts off the water supply.
5. After all faults have been eliminated, the reset button must be pressed, and the system is ready for operation again.

Each famous brand household appliances today use just such a leak protection system, because it is of a double type: Aquastop of the inlet hose - outdoor protection, and protects the technique itself internal system Aqua control.

Inlet hose protection

The industry produces special hoses with built-in mechanisms to shut off the water supply different ways. There are the following systems that are responsible for protecting against unwanted inlet hose leaks:

• mechanical;
• with the use of an absorbent;
• electromagnetic type.

The first option is now used very rarely, but you can find it on budget dishwashers. Bosch machines. The system consists of a valve and springs, designed for a certain water pressure - when a leak occurs, it drops, the spring works and the valve shuts off the water supply. Such a system is not able to recognize small leaks from a fistula, leakage of gaskets, which can cause a lot of harm.

A system with a mechanical type Aquastop recognizes only 147 leaks out of 1,000, and this is only no more than 85% of protection, which today is considered much lower than the norm.

At its core, such a system works like one hose inside another, made of corrugated plastic: if the inner layer is damaged, then the plastic one will be quite reliable protection.

mechanical type

When a leak occurs, the protection system immediately works - the red indicator on the body lights up, the water is turned off.

mechanical valve installed on drain device, after operation due to failure of the hose, it is unsuitable for further operation. Therefore, a new drain hose is installed, which is the main disadvantage of such leakage protection.

Application based protection system absorbent it is used much more often, its action is not difficult: moisture from the leak flows into a special reservoir with absorbent, which instantly swells, expanding at the same time, which blocks the access of water to the dishwasher with a valve.

With absorbent

The main disadvantage is the fact that it also disposable: the absorbent inside the body swells and hardens, tightly closing the valve, excluding the possibility of its reuse, including the hose. Absorbent systems come with a plunger or only with a spring, there are no others in world practice.

Electromechanical the protection system with Aquastop works in a similar way as the system with an absorbent, but its basis is solenoid valve. The body of such a device may have one or two valves. Water flows down the hose into the pan of the Bosch machine, the device with the absorbent begins to absorb it, swells - the valve blocks the access of water to the machine.

Experts say that Aqua-control, working with a solenoid valve, does not provide protection in only 8 cases out of 1000 leaks.

Electromechanical protection system

Possible problems

The main problem with Aquastop hoses is the impossibility of extending them or installing them in hard-to-reach places. Due to the dimensions of a fairly massive body, connecting to a tap can be very problematic. In addition, many users Bosch machines they assure that the case must be installed with the arrow down, so when installing, check your actions with the attached instructions.

If any leakage occurs, the machine gives an E15 error - if the Aqua-control system has worked, check the instructions and everything will become clear to you. But sometimes such a warning is not displayed on the display, but no water coming into the car. In this case, your actions should have the following sequence:

• close the water supply valve to the device;
• unscrew the hose equipped with the Aquastop system;
• look inside the hose - the valve should be visible immediately behind the nut;
• if there is no gap between it and the nut body, the system has worked and water will not pass through such a hose to the machine.

To be completely sure, you need to unscrew the lower front plate, shine a flashlight into the pan: if there is water, then the protection system has worked, it remains to find a leak.

Self installation

Replacing the old hose is not a difficult job - we turn off the water and dismantle the hose, and install a new one in its place. If a system with a solenoid valve was used, then you need to carefully connect the wiring with a plug to the sensor, which is located next to the filling inlet on the machine.

Any system is quite effective and protects your household appliances from various leaks and troubles ending in a flood. It is not in vain that experts advise installing Aquastop protection systems, they work simply - any user who does not have any technical knowledge can replace them.

A rare apartment owner does not know how much misfortune the flooding of the apartment brings due to an open tap in the kitchen or in the bathroom, as well as water leaks in the water supply and heating systems. A flood in an apartment entails colossal material losses and unpleasant proceedings with neighbors living on the floor below. The walls of the apartment flooded with water can cause failure concealed wiring and defeat electric shock. Developed and implemented mass production of flood protection kits will allow you to avoid and forget all the problems associated with it. Next, we will look at how water leakage protection works in an apartment, as well as provide an overview and comparison of the most popular systems today.

Principle of operation and constituent elements

The protection system kit consists of the following elements:

1. Control block.
2. Water leakage sensors.
3. Taps for automatic shutoff of the water supply in the water supply and heating system of the apartment.

Understanding how protection works is not difficult. Sensors are installed in places where leaks are most likely to occur. As a rule, they are installed under bathtubs and washbasins, washing machines and water heating appliances, as shown in the diagram below:

Upon contact with water, a signal is removed from them and fed to the control module (controller), which performs the functions of a dispatcher. Having received a signal about the presence of water in the controlled area of ​​the leakage protection system, the controller sends a command to the electric drive of the ball valve or to the electromagnetic quick-closing valve, which emergency shut off the water in the water supply or heating system of the apartment.

Overview of modern flood protection systems

The possibility of arranging an apartment with flood protection is not a prospect for the distant future. This is one of the real steps that you can take today to implement it in your home. high technology smart home systems. Today, the market is dominated by several complexes that protect the apartment from leaks. Deservedly in demand ready-made kits the following types:

• "Neptune"
• Hydrolok
• "Stop the flood "Rainbow"

Often, an ordinary consumer, faced with a choice of protection, finds himself in a difficult situation and simply does not know which one is best suited to ensure the safety of his apartment from leaks and prevent a flood. The analysis of the working technical capabilities and characteristics of the listed devices will make it possible to compare their advantages and disadvantages, on the basis of which to make a choice required device protection.

Neptune

A product of Russian development, which first appeared on the Russian market back in 2000. The Neptune brand, according to the Moscow Business Times, is the most popular water leakage control system for Russian market. The company's product range has a solution for any budget - from an affordable kit costing less than 10,000 rubles to an ultra-modern one controlled by a smartphone. Neptune water leakage protection can be installed not only on water pipes, but also on heating and water heated towel rails, which also pose a risk of water leakage.

The product line includes ready-made kits for an apartment, as well as individual components, which will allow you to assemble a complete set specifically for your tasks. In addition, Neptune leakage sensors work not only on wires, but also via radio, which allows you to install protection against water leaks at facilities with completed repairs, where it is no longer possible to hide the wires.

The warranty for Neptune water leakage control systems is up to 6 years for all elements of the system.

It is worth noting that the Neptune water leakage protection has been equipped with world-famous Bugatti ball valves, which are made in Italy, for many years. The peculiarity of these taps, in addition to a strong brand in the world of plumbing, premium sealing materials, and electric motor power, is that the electric drive has manual emergency control, that is, the tap can be opened / closed without electricity.

To choose the right Neptune leak protection kit, there are three main points to consider:

1. Are the renovations completed at your facility? If the repair is just starting, then you can choose any Neptune kit, since all control modules support wired sensors. At the stage of repairing a room, they are usually used, since they are cheaper than wireless sensors and you don’t need to change batteries from time to time. Bugatti ProW+ WiFi
2. The diameter of the pipes for water supply, heating or a water heated towel rail. Ready kits Neptune are equipped with ball valves of a certain diameter. For example, the most common faucet size for an apartment is ½ inch. Check with your facility or with your craftsman.
3. The budget allocated for the purchase of the Neptune water leakage control system. The set of options that the consumer will receive depends on the budget.

Neptune Aquacontrol- the most affordable leakage protection system, since the cost is less than 10,000 rubles per set for an apartment (control module, two taps and two sensors). This kit is completed with the Neptun Base module - this is a very simple and reliable control module that will shut off the water in case of a leak and once a month will automatically turn the taps against souring.

Neptune Bugatti Base- it's excellent value for money. As in the previous set, a simple Base module is used, however, ball valves are already Italian made Bugatti with a large margin of safety. The Neptun Base module does not have a backup power supply - if this function is important to you, then pay attention to the modules of the ProW series.

Neptune Bugatti ProW is a kit with extended functionality that works on wired sensors. Additional features of the ProW module:

• Protection of taps from souring (automatic turning of the tap 2 times a month).
• Supply voltage on taps –12 V DC
• Built-in backup power supply.
• Targeting - the ability to indicate leaks in 4 lines.
• The ability to connect warning systems, security systems and integration with a "smart home" (the presence of a low-current relay).
• Ball valve status indication (open/closed).
• Backup power status indication.
• Possibility of opening and closing the ball valve manually (button on the module).

Neptune Bugatti ProW+ similar to the ProW module, but has the ability to work not only with wired, but also with radio sensors - this perfect choice for those who have already completed the renovation of the house.

Neptune Bugatti ProW+ WiFi- This is the most modern and functional interesting control module. Here's what he can do:

• Security system control via smartphone. To do this, just install a free application and synchronize your mobile phone.
• Timely notification of an accident. In addition to the fact that the module emits sound and light notifications on the front panel, additional information about the occurrence of a leak is sent to the screen of your mobile phone. A very important function, especially if no one is at home at this time.
• Monitoring of hot and cold water. Now it is not at all necessary to manually take readings every month by opening the cabinet with counters, which is located in the bathroom or in the kitchen. It is enough to open the mobile application and view the readings in it. This is a very handy feature for those who rent an apartment.
• Backup power supply of the protection system. Even if the power supply to the apartment or house is turned off for a long time (up to 36 hours), the Neptun ProW + Wi-Fi module will work. The developers have introduced batteries into the design, which will be the source of backup power. By the way, the application will notify you in advance of the need to replace these batteries.
• Indication of the position of ball valves. You can not only remotely monitor the taps, but also, if desired, automatically control them (close and open). If, having gone on vacation, you forgot to play it safe and turn off the water, this can always be done through the application.
• Function of automatic turning of cranes. It is a self-cleaning mode of ball valves, which prevents the "souring" of valves. Automatic rotation is carried out every 15 days.
• The Neptun ProW+Wi-Fi control module can be connected to the " Smart House" and burglar alarm residential building. There is a special exit for this.

The table below compares the Neptune models.

How flood protection works using the example of the Neptune kit is shown in the video:

Summary:

1. The Neptune system has earned customer recognition over the years, as sales data show - it is the most popular water leakage protection in Russia (source: Moscow Business Times).
2. Each buyer can choose his system based on the budget and options. The most affordable kit costs less than 10,000 rubles.
3. The Neptune system is equipped with Italian Bugatti cranes.
4. There are very interesting solution Neptun ProW+ WiFi with smartphone control.

In preparing this material, our readers were kindly provided with a 15% discount on the entire range of the Neptune store. Website: systemneptun.rf. Promo code: self-electric.

Gidrolock

Products Russian company"Hydroresource". If we compare with the Neptune device, it can be noted that the principle of its operation is the same, the package includes water sensors, a controller and electric ball valves. The company has developed and put into production several models of leakage protection systems, basic option which serves "Gidroloсk Standard".

Additional options for Hydrolock water leakage protection models:

Gidrolock is equipped with three sensors, technical capabilities this device protection against water leaks provide for the connection of 20 wired and up to 100 wireless sensors. Time of the emergency termination of water to 30 seconds. The manufacturer guarantees 10 thousand working cycles and general guarantee operability of the protection complex is 3 years.

An overview of the Hydrolock kit is shown on the video:

Russian development from the Supersystem company. The principle of operation and equipment are the same as those of the two previous analogues. Thanks to the introduction of innovative materials into the design of taps, efforts to overcome friction are significantly reduced, emergency closing of taps when a leak is detected in the apartment occurs in 3 seconds from minimum cost electricity.

Compared to other systems, "Aquastorage" operates at an operating voltage of only 5 volts. The degree of automation of the control system does not require human intervention. It is completed with four sensors, both wired and wireless options are available. 4 year manufacturer's warranty.

Overview of the "Aquaguard" kit:

Stop flood "Rainbow"

A characteristic feature of this protection system is that all sensors are wireless and operate in the mode of supplying radio signals, the power of which allows them to remain operational at a distance of 20 meters from the controller in conditions apartment building. The product set includes 1 solenoid valve, 4 sensors. The control unit is designed to connect 9 sensors.

Compared to protection systems, Aquastop is just a mechanical device developed by Russian and Italian specialists. Prevents flooding of the room with water in the event of a rupture in the filling hose of the washing machine. Installed in front of the hose with a threaded connection, as shown in the diagram below:

In the event of a leak in the hose and a decrease in pressure in the system, Aquastop will shut off the water in a matter of seconds, which will stop further leakage. The principle of operation of the aquastop is demonstrated in the video:

Comparison of the cost of kits

Finally, we bring to your attention a comparison of the cost of the provided apartment flood protection systems:

0 ) Dislike( 0 )

Leak protection system	Estimated cost (c.u.)
"Neptune"	148-351
«Gidrolock»	219-383
	223-368
"Stop the flood "Rainbow"