How to glue the cabinet with self-adhesive film photo. DIY old cabinet restoration ideas

You will need

- pencil or pen;
- ruler or meter;
- scissors;
- sometimes a circular knife;
- soft cloth;
- hair dryer and wallpaper glue.

Instructions

Renewing your kitchen furniture with self-adhesive tape is significantly cheaper than buying a new one. The stained glass effect can be obtained using film with a transparent pattern. Decorate the bathroom mirror and tiles with ornate designs from the same self-adhesive. Decorate the children's room by sticking bright cheerful drawings on the furniture.

Prepare the surface for work. Clean it from grease, dirt and dust, wipe dry with a clean cloth. If necessary, degrease the base under film dishwashing liquid or (in difficult case) with an alkaline solution. Polished or varnished surfaces are ideal for wrapping.

Prime clean boards or plywood with polyester or primer varnish, you can use methyl wallpaper glue. Treat cracked and uneven surfaces with putty and sand with sandpaper. Then this base must be covered with an acrylic-based primer so that the self-adhesive film adheres well.

Slice film according to your size. On the back of the product there is a centimeter grid, which greatly facilitates the cutting work.

Separate paper base 5 cm film, attach the material to the surface and glue the free edge evenly. Pull the paper back smoothly and evenly with one hand, and smooth the self-adhesive with the other. film soft napkin or towel. Spread the material from the center outward to avoid bubbles. If they do form, pierce this place. fine needle and release the air from under the film.

If you need to stick film on the round corner, heat a piece of the product with an ordinary household hair dryer. Preheated film glue quickly and neatly, pulling slightly, and bend the edges. Cut and bend even corners.

Pape over large surfaces such as walls in the same way as with wallpaper. For overlapping panels, add a 1-1.5 cm allowance. film difficult to put end to end, work neatly, peeling off the paper little by little.

Place the glass on the glass moistened with the detergent solution. film without a paper backing and position it as desired. It is easier to work this way when pasting smooth surfaces. Press the material against the substrate and use a towel to smooth the surface towards all edges, removing water.

Sources:

Adhesive tape

All items have their own term. Likewise, furniture does not last forever. Shabby kitchen cabinet doors, tattered hallway corners and plain bookshelves. Bring them to life! But you say, "There is no money for restoration." There is a budget and at the same time reliable option - self-adhesive film. With its help, you can update any piece of furniture. Even a refrigerator.

You will need

Self-adhesive film,
Rubber spatula,
Scissors,
Ruler,
Pencil or ballpoint pen
Needle,
Rag,
Cleaning agent,
Primer.

Instructions

You have decided to change your interior, add colors to it, or maybe just give a neat look to your favorite wardrobe. Start with preparation. Together with the film, buy a special rubber spatula at the hardware store. It will make it easier for you to smooth out film on the surface. Then slice film into the desired pieces, but do not forget to leave allowances around the edges. Now prepare the surface for work. Clean it from the dirt, greasy stains... Eliminate unevenness. In some cases, it makes sense to remove the old coating and treat the surface with a primer.

Stage two - gluing the film. Peel back the backing paper two centimeters from the edge. Cut it off. Attach film to the surface (remember the allowances) and attach evenly. Press down firmly with a rubber trowel and work towards the edge. Do not make sudden movements, the film may lie unevenly. If bubbles form, pierce them with a needle and walk over the puncture site with a rubber spatula. Then tear off another 4-5 centimeters of the protective paper and go through the procedure. Do not hurry. Glue film gradually, helping yourself with a rubber spatula. When the main surface is pasted over, you can start processing the edges. Carefully fold over the remaining film, also smoothing it with a spatula. If necessary, make cuts to help the film lay more evenly.

The third stage is to consolidate the result. To make your renovated furniture last as long as possible, cover it with varnish. Try to apply the solution in a thin layer. Avoid smudges and unevenness, then your updated cabinet will serve you for a long time. You can also renovate the walls in the room with the self-adhesive film. For example, in the nursery. For such cases, there are special coatings that you can paint on. The wall, as well as the surface of the furniture, should be processed before starting work. The mechanism for gluing the film on the wall is the same as on the cabinet.

Kinds self-adhesive wallpaper

Glossy or matte washable patterned, these are the best self adhesive wallpaper for the kitchen
Self-adhesive cork wallpaper with excellent heat and sound insulation properties.
Wood-like wallpaper imitating the structure and color of wood.
Mirror film, this is a self-adhesive wallpaper for a bathroom or hallway
Imitation of textured plaster.
Self-adhesive photomurals, fabric-based

How to glue self-adhesive wallpaper

It is necessary to glue the self-adhesive film on a smooth surface. Best of all, such wallpaper adheres to laminated, wooden, paper, painted surfaces. If, nevertheless, there is a need to arrange a plastered wall, it should be pre-primed well. On other surfaces, self-adhesive wallpaper can be glued without preparation, which makes repairs much faster. Quite dense wallpaper does not even require preliminary leveling of the wall - the film is simply stretched and levels it itself.

It is important to glue self-adhesive wallpaper without air bubbles. Unlike paper, films are air-tight, so they will stay when the glue dries. It is most convenient to start from the bottom, gradually peeling off the protective paper and ironing the surface with a roller. In no case should the entire adhesive layer be exposed at once - there is a high probability of wallpaper sticking to each other and other unnecessary surfaces. If bubbles do appear, they need to be pierced with a very thin needle and carefully ironed with a roller.

For working on smooth surfaces that are not afraid of moisture ( ceramic tile, plastic, Oil paint) you can use soapy water. It should be sprayed on the wall, then apply the wallpaper, and the moisture allows you to move them along the surface, choosing the desired position. Then the water will dry and the wallpaper will stick tightly. Sometimes it becomes necessary to glue wallpaper onto curved surfaces. Vinyl can be stretched slightly by heating it with a hair dryer.

In this regard, I would like to talk about one of the fairly popular wall coverings, namely, self-adhesive wallpaper. They have traditionally been used in bathrooms and kitchens, however modern technologies helped to significantly expand the range of applications of this type of finishing material.

What materials are self-adhesive wallpapers made of?

Stores are ready to offer customers wallpaper made of the following materials:

· Pvc ... This name hides a rather familiar film, presented in various color schemes... Its use can be considered especially relevant in summer cottage conditions. This is the easiest way to refresh the surface of your furniture without investing a lot of money. Also PVC application films are justified in the kitchen and in the bathroom. Synthetic material is not afraid of changes in temperature and humidity. Perfect for wet cleaning.

· Satin ... They make of it fabric wallpaper... They are used for living rooms... Self-adhesive satin wallpaper has excellent performance characteristics(strength, moisture resistance). Often they become the basis for applying photo printing.

· Cork ... Appeared on the market finishing materials relatively recently and due to its significant cost, it is not so widespread. Suitable for the decoration of any room, environmentally friendly, creates inimitable comfort and charm.

· Chalk wallpaper ... Completely new, but at the same time, familiar from childhood material. Surely each of us remembers the blackboard that so attracted us to primary school... So, this type of self-adhesive wallpaper completely imitates its surface. Conveniently? Certainly! Plus, it is very fashionable to have at least one wall with such a coating in the house. It will be especially relevant in the nursery, hallway or kitchen.

How to glue self-adhesive wallpaper

There should not be any special difficulties when gluing such wallpapers, because many of us in childhood were fond of collecting various stickers, so the gluing technology is familiar. Nevertheless, it is worth paying attention to a number of features that can create significant difficulties if they are not taken into account:

1. The wall or other surface must be perfectly flat. As practice shows, the bulk of our houses needs leveling of the walls. This is an indispensable condition. Otherwise, the surface will turn out to be rough, and in the case of poor-quality plaster, the wallpaper may disappear altogether.

2. At the time of work, all unnecessary things should be removed from the wall. We are talking about sockets, switches, shelves.

3. The surface to be glued must be damp. In this case, the wallpaper will set better, and the likelihood of bubbles will decrease.

4. Pasting is performed from the side of the window with an overlap of 1 cm. This technique allows you to make the joints as invisible as possible.

Pay close attention to these tips and the results will not disappoint you. Self-adhesive wallpaper- an easy-to-use finishing material that attracts buyers with its functionality, durability and wide choice colors.

At the same time spending the minimum amount of funds?

Many people ask this question, because with the help of this material, you can easily transform the interior of an apartment.

Self-adhesive film has gained its popularity not very long ago.

She is for short term has gained popularity among those who want to make their home beautiful and comfortable without much hassle.

This film is produced for different types surfaces.

Despite this, they are all made using the scotch tape principle.

In what cases is it used

The only disadvantage of self-adhesive tape is that it can form bumps and bubbles on the surface. Therefore, such material should be glued very evenly.

Otherwise, furniture or doors may not look very attractive. In addition, there will be poor adhesion to the surface and the film will begin to spontaneously detach.

Before purchasing such a material, you should first determine on which surface it will be applied. The chosen colors and films depend on this.

For example, furniture is very often pasted over with only small, separate fragments. These can be pictures, or separate parts of a self-adhesive film.

With their help, you can easily add colors to old, long out of fashion furniture, and "revive" it.

As another option, such material is used to protect the surface. In this case, the transparencies... To decorate and protect window surfaces, it is best to use a special stained glass window with a mosaic ornament.

For pasting bedrooms, living rooms and a child's room, the film is perfect, which is available in the form of self-adhesive compositions. They fit perfectly with the usual wall covering and can add originality to any room.

Since one of the most important advantages of such a material is its resistance to moisture and ease of maintenance, the bathroom and kitchen can be pasted over with it not partially, but completely. You can select only those parts that are most frequently contaminated.

It is not difficult to remove dirt from the surface of the self-adhesive film. To do this, use a sponge with a drop of any detergent applied. Acetone or ethyl alcohol will do as well.

Do not rub the film too much or use strong cleaning powders. These can easily damage the surface of such a finishing material.

Pasting

To work with self-adhesive film, you must prepare the following materials from the list:

simple pencil
sharp scissors
hair dryer (special construction)
ruler
special spatula for felt

How to glue self-adhesive foil on furniture without bubbles?

Before starting work, you should put the surface in order.

To do this, you need to remove the glue and the coating that was before.

The wall or furniture must be thoroughly cleaned and then degreased with alcohol or gasoline.

After that, it should be well dried with a construction or regular hair dryer.

The most better mount for such a film is capable of providing a smooth coated surface.

If the coating is slightly rough or matte, it should be well smeared with a primer or polyester varnish. Methyl glue is also suitable for this purpose.

If the self-adhesive film will be applied to chipboard, wood or plywood, then before starting finishing works they should be well cleaned of dirt or dust. In addition, experts recommend treating these surfaces with a putty or primer mixture. This will help the adhesion of such materials better.

The surface should be slightly moistened. To do this, wipe it with a cloth soaked in water. Otherwise, the self-adhesive tape may not adhere to it.

Since such a coating is very often applied not in whole canvases, but in small fragments of the required shape, during such work they are guided by the centimeter markings on its reverse side.

Almost all film sold in stores is equipped with these designations. But if material was purchased that does not have such markup, it is best to do it yourself.

In this case, the self-adhesive tape is easily cut off. It is best to cut out fragments of this with scissors or special knife... During these manipulations, be sure to leave a small margin.

It should be from 1 to 2 cm. Basically, the correct cutting of the self-adhesive film depends on the direction in which the pattern is on its surface.

If such a finishing material looks like a tile, then it is best to do it at the seams. And if the pattern has a rapport, it is best to cut it from the side of the upper face layer.

Such a film does not create difficulties in gluing. But the best thing is not to rush too much during such work. In this case, the coating will lie flat and will not bulge.

You should know that applying this product to furniture made of wood, as well as glass or doors will be many times easier than pasting over the entire bathroom or kitchen.

Remaining stages

How to glue self-adhesive foil on patterned furniture?

You should take a pattern and separate it. upper layer from the substrate.

Do not immediately glue such a film tightly.

It is best to first apply this coating to the surface and find out if the shape and size fits well with the selected piece of furniture or walls.

This means that you first need to apply the first 5 cm of such a canvas, then the next 5 cm, etc.

At each of these steps, spread the film over the surface with gentle movements. In this case, you need to constantly monitor that there are no creases and bubbles.

To do this, iron it immediately using a dry cloth. In order to prevent bubbles from appearing on such a finishing material, you should proceed according to the following principle.

Smoothing should be done from the center of the self-adhesive tape to its edges. It is like applying wallpaper to a wall.

If suddenly the film is swollen in some places, you should immediately level its surface. This needs to be done until she can adhere to her completely.

To do this, the film is carefully torn off and re-glued to the same place. If such a coating is applied to the bathroom wall, it is imperative to first coat its surface with wallpaper glue. The film should be glued on while the mixture has not yet had time to dry.

Smooth the canvas with a dry cloth. The directions of movement should go from the center in different directions.

Necessary care

Such a film does not require too much maintenance. It is enough to follow the recommended rules:

If the canvas is dirty, it is easy to fix it with ethyl alcohol.
Do not use gasoline or similar substances to clean the surface.
Do not use abrasive substances.
If the glue comes out of the edges, then the composition that remains superfluous should be wiped off with a rag that is soaked in ethyl alcohol.

As for painting these products, such work is not recommended. The fact is that the funds will not fit well on the surface of the self-adhesive film.

How to install the film on glass and remove bubbles, you can watch the video:

Self-adhesive film is a convenient and widely used finishing material, which has a number of advantages:

It can be applied to different types surfaces.
This material is durable, practical, environmentally friendly, has an extensive color palette, making it perfect for any interior design. It is also able to update old, shabby furniture so that it looks like it’s fresh from the store.

Examples of using self-adhesive tape

How to cover furniture with foil yourself

So, pasting furniture with self-adhesive film is not the most difficult task, but you still need to know a number of features. Before purchasing the film, you need to measure the furniture to be pasted. And already in accordance with these dimensions, acquire it, not forgetting that the rolls have different widths.

The process of gluing furniture itself is as follows:

It is necessary to remove all handles and other unscrewed decorative elements from furniture.
Then, the surface must be thoroughly rinsed and degreased. To do this, you can use detergent or ethyl alcohol. This procedure will be sufficient if the surface is polished or varnished, without damage.
And if you are dealing with a surface made of plywood or boards, then it requires a preliminary priming with methyl wallpaper glue or polyester varnish. If cracks and damages are found in the furniture, they should be repaired with sandpaper, putty and covered with acrylic primer.
Next, a piece of film of the size you need is cut off. On her inside there is a special centimeter grid, along which it is easy to cut the film evenly.

How to properly stick the film without bubbles

When pasting, the film is separated from the paper by several centimeters, applied to the surface, after which it must be pulled off with one hand, and smoothed with the other using a clean, dry cloth. Getting rid of bubbles in this way. If, after pasting, they still remain, they can be removed by piercing with a needle.

Or, you can use another way to avoid bubbles. To do this, sprinkle the surface with a mild soapy solution before gluing. In this case, the film will slide, and it will be much easier to eliminate air bubbles.

After renovation works often there are finishing materials that are a pity to throw away. For example, wallpapers that are sold in large rolls, etc. How do I use them? You can glue them over cabinets, bedside tables, doors, and other furniture.

With this simple action, you will immediately kill two birds with one stone, use the remnants of the finishing material and decorate the old, well-worn furniture. To carry out such work, you do not need any special skills, but we will now tell you how to do this.

A bright accent in a calm kitchen

Wallpaper

You have probably heard more than once that wallpaper is used to decorate various interior items. How many master classes have you seen on TV from designers of all stripes, because each of them considers it their duty to give a second life to some household item.

This is done most often with high-quality vinyl wallpaper or non-woven wallpaper, since it is extremely difficult to work with paper options, and you have to sweat a lot to get at least a satisfactory result.

Therefore, if you still have wallpaper, before you get involved in pasting surrounding objects, make sure of the quality of the finishing material.

The choice of color and texture is also limited with us, since we work with residual material, but if you want to buy a new roll for this purpose, then start from overall design the room and their taste guidelines.

Decorating kitchen furniture with wallpaper

It is perfectly acceptable to paste over the furniture in the room with canvases with the same pattern as on the walls. Such an interior will look quite harmonious and holistic. If you need to use a different type of wallpaper, then do not forget about the general design concept of the room.

Application of simple design solutions, will make more harmonious interior... For example, if the room is finished in light colors, then for pasting cabinets it is good to use dark or bright options... If the walls in the room are pasted over with wallpaper with an ornament, then in order to avoid overloading the interior, the furniture is pasted over with plain canvases. It will look very cool interior decoration cabinet, made to match the walls of the room.

A good option for decorating cabinets is an imitation of other finishing materials, wood, brick, leather, stone. Such vinyl wallpaper is often used for decoration different rooms and they naturally remain. In addition, such canvases have significant relief and repetitive patterns, which will help hide defects on the surface of the furniture.

The classic option for decorating the wardrobe

V building stores you can find special photomurals designed for pasting doors and cabinets. Usually these are paper versions, which depict non-trivial plots, less often a banal imitation of a wooden covering.

In fact, the easiest way to cover a wardrobe under a tree is with self-adhesive film, which is just available in such colors. German and Dutch films are more expensive and of better quality, Chinese ones are cheaper, but this film often has edges that are not of the best quality.

Note that self-adhesive wallpaper can be monochromatic, stained glass, if this option suits you, use it.

If you are going to paste over Kitchen Cabinet or a bedside table in the corridor, it is desirable that the wallpaper is moisture resistant for holding wet cleaning... You need to think about this in advance. Self-adhesive film has moisture resistant qualities, like most vinyl wallpaper, but the paper is weak.

The use of green and white colors that blend into the interior

If you only have paper leftovers, in principle you can use them, but after pasting you will need to add gloss and protect the canvases from moisture.

We make pasting

We collect the necessary materials

Before starting work, you need to take care of the tools and material. Here's what comes in handy:

sandpaper (sandpaper), the corresponding attachment for a drill or grinder, for preparing the surface for pasting;
in some cases, a construction hairdryer, but not necessarily;
measuring instruments - ruler, tape measure, corner;
tools for markings and marks - pencil, pen, marker;
cutting tool - knife, scissors;
wood primer and putty for preparatory work;
tools for applying compounds - roller, brush, spatula;
rags for smoothing and removing glue;
PVA glue.

Using a grinder to sand surfaces

As you can see, the list is quite impressive. If you do not have any materials, buy them in addition. By the way, if the fittings of your furniture are worn out, then you can change it too. For example, a handle, a new cabinet handle will not be expensive, but it will add color to your newly-pasted furniture.

Preparatory work

Before wallpapering furniture, you need to take care of the surface on which you will apply the material. We need to make it suitable for such work, so we will perform the following manipulations:

Typical domestic kitchen cabinet after decoration

To make it easier to work with a wardrobe or bedside table, you need to disassemble it, remove all accessories from it.
The next step is to sand decorative surface, remove the entire layer of varnish from it. This can be done with a sandpaper, which is very laborious, it will be easier to put on a drill, grinder or screwdriver the appropriate nozzle and walk over the varnish.

You can also remove the varnish using construction hair dryer... For this, the surface is heated and the applied composition is scraped off with a spatula. But even in this case, sanding is indispensable.

If your furniture is made of solid wood and has not been processed with anything, then it is recommended to go through with a zero sandpaper to create some roughness.
In the next step, we remove all the dust from the skin, for which we use a damp cloth. We give the furniture some time to dry.
Having examined the dried surface for defects, we decide whether to putty it. If the cracks and grooves are not so large, and the wallpaper for pasting is embossed, you do not need to do this. If the defects are deep, you will have to level the surface with putty, maybe even in several layers.
As you probably already guessed, after the putty has dried, the putty places need to be processed, leveled with total surface... This is done in the same way with sandpaper.
Now the surface of the cabinet is almost ready, all that remains is to prime it for better adhesion to the wallpaper.

Carrying out preparatory work will provide 80% of success, even if you cannot glue the wallpaper beautifully the first time, you will already have a base for further experiments.

Pasting

Pasting of furniture also takes place in several stages:

Wallpapering furniture

First of all, it is worth making blanks from the remnants of wallpaper. For this, the item is carefully measured and the dimensions are transferred to the wallpaper. Some patterns are cut out in accordance with the dimensions of the cabinet or bedside table.
Next, the prepared surfaces are coated with glue. You can use wallpaper glue, but it is better to use construction PVA, it will glue materials better. It is necessary to apply the cut pieces to the surface of the cabinet carefully, try to immediately level the canvas. This is not so difficult to do, since the patterns are small in size.
It is recommended to stock up large quantity dry rags or rags to smooth the sheets and remove glue residues from them. A special pressure roller will help to press the pieces more tightly.
After pasting the cabinet or other furniture with wallpaper, it is necessary to give the glue some time to dry, and only then screw the fittings. Usually a few hours are enough, but in the case of large items, it may take a day.

As with standard wallpapering, try not to create indoors, there is some possibility that the sheets will not adhere well.

The manifestation of imagination in the interior of the kitchen

Actually, that's the whole technology of decorating pieces of furniture with wallpaper. Definitely, after these manipulations, your wardrobe will look better, certainly more interesting than if you painted it.

You can glue the cabinets yourself, as you can see, there is nothing complicated here, it is enough to put a little effort, patience and accuracy. In addition, the restoration of such items with your own hands will give you confidence in own forces and will confirm that you have design skills. Try it, perhaps the world does not yet know the name of a new, successful designer.

Using adhesive film for furniture is an inexpensive and easy way to give a second life. old furniture, doors, glass, walls and other surfaces.

The film may come in handy on rented apartment when you don't want to spend money on buying new furniture, and also if you want to show imagination and turn a boring wardrobe or chair into a small masterpiece.

Many are experimenting with country furniture, which, after decor, gains fresh look and can last for more than one year.

The surface will give a zest to the material with a shade natural wood or marbled, with geometric patterns or abstraction. Moreover, the choice of colors in stores is very large.

The advantages of self-adhesive film include:

price,
availability,
ease of use,
moisture resistance,
durability,
health safety,
the ability to wash with water.

But in order for the film to cope with its tasks, it is important to stick it correctly.

How to paste over furniture - types of films for pasting furniture

The choice of material should be approached responsibly, because in the markets and in the store you can find cheap plastic and polypropylene options, which are inconvenient to use and do not provide the desired result.

The best option is polyvinyl chloride, or PVC, which is traditionally used in everyday life and is recognized as safe and reliable.

It is necessary to make sure that the material has a protective layer, this is especially important if you have to work with kitchen furniture. High loads, exposure to food products, impacts from sharp products can quickly damage the material, and the film will not last more than a month.

Cheap material loses color very quickly. To prevent this from happening, buy options with a layer of ultraviolet stabilization, which will keep the furniture from exposure to sunlight.

For the kitchen and bathroom, choose moisture-resistant models, and if the furniture will be used near heating devices, the pasting is performed using a thermally stable polymer.

Also, self-adhesive tape can be used as a means of protection, for example, against moisture accumulation.

Those who appreciate natural shades should choose self adhesive wallpaper for furniture painted with wood, stone, fabric or ceramics. But it will look stylish only if the material is really High Quality, and not a cheap Chinese fake, not even remotely similar to the original.

For decoration of furniture in the hallway, as well as in rooms with low lighting, designers recommend using a glossy film, and for a bedroom or kitchen - matte.

Those who are confident in their taste may prefer not boring monochromatic options, but material with luxurious patterns with a polymer coating.

VIDEO INSTRUCTION

We glue the film on furniture step by step - application technology

Since the film is not afraid of high temperatures and moisture, is easy to clean and practical, it can be used in the following rooms:

Kitchen. You can paste over both furniture and other surfaces that are often amenable to contamination. It is especially convenient to use self-adhesive material in the kitchen in a private house.
Bathroom. Here, using this material, you can protect the walls from moisture, soapy foam.
Children's. It is easy to remove paint, markers and other contaminants from the film.

Consider the procedure for pasting various surfaces with film:

Surface preparation- the first and most important stage. The base for the film must be free of all dirt, and ideally also varnished. You can also prime uneven surfaces with wallpaper glue or varnish.
Cutting the material... Pieces of film should be with a margin. It will also be easier to cut if there is a scale on the back.
Separating from protective film ... On the reverse side, the manufacturer usually indicates recommendations for the use of the material, study them and adhere to. Apply the material to the base and, holding it with one hand, remove the protective layer, and smooth out the air bubbles with the other. Until the film has set, there is a little time to touch up the material and lay it smoother. After a few hours, it will completely seize, and it will no longer be possible to correct the result. To facilitate the bonding process, many wet the surface to make it easier to trim.

To ensure that the service life self-adhesive film for kitchen or living room was long, it is recommended to follow the following tips:

remove light stains from the surface using a warm solution with a mild detergent,
more serious pollution will help to wash off ethyl alcohol,
do not use acetone, gasoline and other aggressive liquids, as well as abrasive substances that leave scratches.

VIDEO ON TOPIC

to slow down the speed of gluing, sprinkle it with powder, it will make it easier to join the drawings,
if bubbles remain after gluing, pierce them with a thin needle,
when pasting metal or glass, wet the surface with water and detergent,

And if the film is bored and you need to remove it, use the following algorithm:

Wet the surface hot water and after a few minutes try to separate it with a sharp object - a spatula or knife. Try not to damage the base, because you have to stick a new film on it.
If hot water did not help, heat the surface with a hairdryer. You can use a regular hair dryer, but a more powerful industrial one.
In addition to the hair dryer, you can use the fan heater at maximum power. The material will soften and it will be easier to lag behind the surface.
If glue remains on the surface, gasoline, thinner or alcohol will help get rid of it.

Thus, universal and practical material self-adhesive film will help to change the design of the apartment with minimal cost and experiment with the implementation of design ideas.