Use of self-adhesive film for furniture set. How to cover a kitchen cabinet with self-adhesive foil

You will need

- pencil or pen;
- ruler or meter;
- scissors;
- sometimes a circular knife;
- soft cloth;
- hair dryer and wallpaper glue.

Instructions

Update kitchen furniture using self-adhesive tape - it is much cheaper than buying a new one. The stained glass effect can be obtained using film with a transparent pattern. Decorate the bathroom mirror and tiles with ornate designs from the same self-adhesive. Decorate the children's room by sticking bright cheerful drawings on the furniture.

Prepare the surface for work. Remove grease, dirt and dust from it, wipe it dry with a clean cloth. If necessary, degrease the base under film dishwashing liquid or (in difficult case) with an alkaline solution. Polished or varnished surfaces are ideal for wrapping.

Prime clean boards or plywood with polyester or primer varnish, you can use methyl wallpaper glue. Treat cracked and uneven surfaces with a putty and sand with sandpaper. Then this base must be covered with an acrylic-based primer so that the self-adhesive film adheres well.

Slice film according to your size. On the back of the product there is a centimeter grid, which greatly facilitates the cutting work.

Peel off the backing paper of the film by 5 cm, attach the material to the surface and glue the free edge evenly. Pull the paper smoothly and evenly with one hand, and smooth the self-adhesive with the other. film soft napkin or towel. Spread the material from the center to the edges to avoid bubbles. If they do form, pierce this place fine needle and release the air from under the film.

If you need to stick film on round corner, heat a piece of the product with an ordinary household hair dryer. Preheated film glue quickly and neatly, pulling slightly, and bend the edges. Cut and bend even corners.

Cover large surfaces such as walls in the same way as with wallpaper. For overlapping panels, add an allowance of 1-1.5 cm. Self-adhesive film difficult to put end to end, work neatly, peeling off the paper little by little.

Place the glass on the glass moistened with the detergent solution. film without a paper backing and position it as desired. It is easier to work this way when pasting smooth surfaces. Press the material against the base and use a towel to smooth the surface towards all edges, removing water.

Sources:

Adhesive tape

All items have their own term. Likewise, furniture does not last forever. Shabby kitchen cupboards, tattered corners of the hallway, and plain bookshelves. Bring them to life! But you say, "No money for restoration." There is a budget and at the same time reliable option - self-adhesive film. With its help, you can update any piece of furniture. Even a refrigerator.

You will need

Self-adhesive film,
Rubber spatula,
Scissors,
Ruler,
Pencil or ballpoint pen
Needle,
Rag,
Cleaning agent,
Primer.

Instructions

You have decided to change your interior, add colors to it, or maybe just give a neat look to your favorite wardrobe. Start with preparation. Buy together with the film at hardware store special rubber spatula. It will make it easier for you to smooth film on a surface. Then cut film into the desired pieces, but do not forget to leave allowances around the edges. Now prepare the surface for work. Clean it from the dirt greasy stains... Eliminate unevenness. In some cases, it makes sense to remove the old coating and treat the surface with a primer.

Stage two - gluing the film. Peel back the backing paper two centimeters from the edge. Cut it off. Attach film to the surface (remember the allowances) and attach evenly. Press the rubber trowel firmly to the surface and work towards the edge. Do not make any sudden movements, the film may lie unevenly. If you have bubbles, pierce them with a needle and walk over the puncture site with a rubber spatula. Next, tear off another 4-5 centimeters of the protective paper and go through the procedure. Do not hurry. Glue film gradually, helping yourself with a rubber spatula. When the main surface is pasted over, you can start processing the edges. Carefully fold over the remaining film, also smoothing it with a spatula. If necessary, make cuts to help the film lay more evenly.

The third stage is to consolidate the result. To make your renovated furniture last as long as possible, cover it with varnish. Try to apply the solution in a thin layer. Avoid smudges and irregularities, then your renewed cabinet will serve you for a long time. You can also update the walls in the room with the self-adhesive film. For example, in the nursery. For such cases, there are special coatings that you can paint on. The wall, as well as the surface of the furniture, should be processed before starting work. The mechanism for gluing the film on the wall is the same as on the cabinet.

Views self-adhesive wallpaper

Glossy or matte washable patterned, these are the best self-adhesive wallpaper for the kitchen
Self-adhesive cork wallpaper with excellent heat and sound insulation qualities.
Wood-effect wallpaper imitating the structure and color of wood.
Mirror film, this is a self-adhesive wallpaper for a bathroom or hallway
Imitation of textured plaster.
Self-adhesive wallpaper, fabric-based

How to glue self-adhesive wallpaper

It is necessary to glue the self-adhesive film on a smooth surface. Best of all, such wallpaper adheres to laminated, wooden, paper, painted surfaces. If, nevertheless, there is a need to arrange a plastered wall, it should be pre-primed well. On the other surfaces, self-adhesive wallpaper can be glued without preparation, which makes repairs much faster. Quite dense wallpaper does not even require preliminary leveling of the wall - the film is simply stretched and levels it itself.

It is important to glue self-adhesive wallpaper without air bubbles. Unlike paper, films are air-tight, so they will stay when the glue dries. It is most convenient to start from the bottom, gradually peeling off the protective paper and ironing the surface with a roller. In no case should the entire adhesive layer be exposed at once - there is a high probability of wallpaper sticking to each other and to other unnecessary surfaces. If bubbles do appear, they need to be pierced with a very thin needle and carefully ironed with a roller.

For working on smooth surfaces that are not afraid of moisture ( ceramic tile, plastic, oil paint) you can use soapy water. It should be sprayed on the wall, then apply the wallpaper, and the moisture allows you to move them along the surface, choosing the desired position. Then the water will dry and the wallpaper will stick tightly. Sometimes it becomes necessary to glue wallpaper to curved surfaces. Vinyl can be stretched slightly by heating it with a hair dryer.

In this regard, I would like to talk about one of the fairly popular wall coverings, namely, self-adhesive wallpaper. They have traditionally been used in bathrooms and kitchens, however modern technologies helped to significantly expand the range of applications of this type of finishing material.

What materials are self-adhesive wallpapers made of?

Stores are ready to offer customers wallpaper from the following materials:

· Pvc ... This name hides a film that has become quite familiar, presented in various colors. Its application can be considered especially relevant in summer cottage conditions. This is the easiest way to refresh the surface of your furniture without spending a lot of money. Also pVC application films are justified in the kitchen and in the bathroom. Synthetic material is not afraid of changes in temperature and humidity. Perfect for wet cleaning.

· Satin ... Make of it fabric wallpaper... They are used for living rooms... Self-adhesive satin wallpaper has excellent performance characteristics (strength, moisture resistance). Often they become the basis for applying photo printing.

· Bung ... Appeared on the market of finishing materials relatively recently and, due to its significant cost, is not so widespread. Suitable for the decoration of any room, environmentally friendly, creates unique comfort and charm.

· Chalk wallpaper ... A completely new, but at the same time, material familiar from childhood. Surely each of us remembers the chalkboard that so attracted us to primary school... So, this type of self-adhesive wallpaper completely imitates its surface. Conveniently? Of course! Plus, it is very fashionable to have at least one wall with such a coating in the house. It will be especially relevant in the nursery, hallway or kitchen.

How to glue self-adhesive wallpaper

There should not be any special difficulties when gluing such wallpapers, because many of us in childhood were fond of collecting various stickers, so the gluing technology is familiar. However, it is worth paying attention to a number of features that can create significant difficulties if not taken into account:

1. The wall or other surface must be perfectly flat. As practice shows, the bulk of our houses needs leveling of the walls. This is an indispensable condition. Otherwise, the surface will turn out to be rough, and in the case of poor-quality plaster, the wallpaper may completely disappear.

2. At the time of work, all unnecessary things should be removed from the wall. We are talking about sockets, switches, shelves.

3. The surface to be glued must be damp. In this case, the wallpaper will grip better, and the likelihood of bubbles will decrease.

4. Pasting is performed from the side of the window with an overlap of 1 cm. This technique allows you to make the joints as invisible as possible.

Consider these tips with due attention and the result will not disappoint you. Self-adhesive wallpaper - an easy-to-use finishing material that attracts customers with its functionality, durability and a wide range of colors.

Imagine a situation - it wasn't long before the planned renovation, but the furniture located in the house got wet or, conversely, dried out. Another option is to move to a rented apartment that has a very poor environment that negatively affects the people living in the room.

The best solution to the problem in this case would be a self-adhesive film for furniture, which will quickly improve the situation without resorting to significant costs. This material is available in a variety of options, providing the ideal selection of a specific modification for each specific case.

If you want to subject your furniture to a quick and high-quality restoration using film, then you should seriously approach the choice required material... In particular, it is worth checking carefully what substance it is made of, because there are often cheap polypropylene and polyethylene models on the market, with which it is fundamentally impossible to paste over a large object.

The best option would be polyvinyl chloride (PVC), traditionally used in many spheres of human activity, from which high-quality self-adhesive film is made.

You also need to pay attention to the presence of an additional protective layer. For example, pasting a kitchen table will require extremely high strength, since this piece of furniture is constantly exposed to high load, exposure to aggressive external environment and blows with sharp objects.

If you ignore this requirement, then the self-adhesive film will not last even one month - soon only individual flaps will remain of it.

In addition, high-strength material should also be glued to the table in the nursery - it will protect furniture from spilled paints, ink from disassembled pens, as well as other contaminants that are almost impossible to remove from wood-based panels.

Using cheap self-adhesive film, many people are surprised to find that after a while it loses its original brightness of colors - they have to re-glue the material on furniture, risking damage to it and spending additional money.

In order to avoid such a problem, it is necessary to choose a model with an additional layer of ultraviolet stabilization - such a film is shown in the photo above. In addition, this type of protection can be useful when using a transparent layer that is glued to various objects - it prevents the exposure of harmful hard sunlight to furniture and household appliances.

The most expensive modifications are distinguished by the presence of other layers - in particular, for the kitchen and bathroom will do moisture resistant self-adhesive film. In the immediate vicinity of the heating devices presented kitchen stove, boiler, water heater, pasting is done using a thermally stable polymer.

As in the previous case, such a self-adhesive film can also be used as an individual protective device - in the photo above you can see the option to protect the tree from the accumulation of excess moisture.

Aesthetic properties

Depending on what goals you want to achieve, the self-adhesive film that is optimal for this application can be of different types. Therefore, before gluing this material, create a small repair project in the form of a sketch.

You will do the most right thing if you take the original photo of the room and apply a drawing to it using a graphic editor.

Those who are not very good at using specialized software, it is worth using the self-adhesive film itself, which can be easily applied to paper.

In order to visually create more space in the room, you should glue a mirror layer on some furniture. Such a solution will bring an original element to the design of the premises, and will also help improve the psychological comfort of the residents small apartments... In this case, pasting is usually done using a matte material - an overly bright self-adhesive film can overshadow all other parts of the room, distracting too much attention.

In the photo, you can also see that even reflective material can have different color tones - you can also choose any of them that best suits the overall design concept.

Lovers of natural materials can be recommended to choose a self-adhesive film, stylized as:

a rock;
ceramics;
wood;
the cloth.

However, it is worth gluing it to furniture only if the product is of a sufficiently high quality. Often on the market there are goods produced by Chinese enterprises that have an unaesthetic appearance... To stick such a film means to spoil the appearance of the room with a cheap imitation, which does not even remotely resemble the original.

You will do the right thing if you choose a self-adhesive base from a well-known manufacturer - in this case, you can get a result similar to the one shown in the photo.

In addition, glossy self-adhesive film is widely represented on the market, which has a rather original appearance. The scope of its application is rooms with a low level of illumination and not intended for permanent residence of people. In particular, gloss can be used to decorate furniture in the hallway or corridor.

For the kitchen, bedroom, hallway, office, it is better to choose a matte version. In addition, the self-adhesive film with good light reflectance is suitable for original design ceiling.

If you want to give free rein to your artistic imagination, then you can glue not a plain material, but real works of art made in the form of a polymer coating.

An example would be original kitchen, which is presented in the photo - it is not difficult to buy such an option, and its price will not be much higher than that of a traditional self-adhesive film. In this case, it is necessary to comply with the same condition as when choosing a product for natural material - only high quality will allow you to achieve the beauty of the image.

Method of work

The beauty of a self-adhesive film is that in order to properly stick such a finishing agent, you do not need to invite professional worker... It is enough just to perform a simple preparation, which is quite within the power of any person.

The main condition is to glue the film only in good lighting conditions, otherwise you may not notice minor defects, which will be impossible to eliminate later.

First of all, it is necessary that the furniture is smooth and does not have external defects in the form of bumps, large cracks, frozen drops of paint, burrs and other things. Therefore, before applying the self-adhesive surface, it is worth polishing the object with which you plan to work. This can be done using manual tools, and using a special electric machine with brushes.

The final stage will be degreasing the surface - this is necessary condition, without which the self-adhesive base can shrink, forming numerous folds and depressions.

In addition, it is allowed to glue the material only on perfectly clean furniture - otherwise, dirt will cause rapid peeling. decorative coating... After completing all the preparation processes, you can proceed to cutting the film itself.

You just need to cut out the required piece, having previously outlined its shape and dimensions. Don't worry if you don't have a large enough lineup - many manufacturers pre-line the back of their products into squares with specified side widths. It remains only to glue the film by removing the protective coating from the sticky part - gently attach it to the object being processed, starting from the top. As you go down, gradually smooth it out to release excess air from under it, which is the cause of the formation of serious defects.

Currently, in stores you can find an endless number of all kinds of wardrobes, dressers, shelves, hanging shelves, multifunctional boxes for clothes and personal belongings. But if you decide not to dive into a long search, but to follow the thread of your imagination, then with the help of the following master classes you will learn how to update old wardrobe with your own hands beyond recognition.

After reading the article, you shouldn't have any questions about how to paint lacquered, chipboard or wooden cabinet what paint to paint and make it suit your own style, and you will also learn some of the intricacies of this work.

Painting - This is the most reliable and thorough method.
Wallpaper, self-adhesive film and decoupage - when choosing this method, remember that it is not durable!
Cloth upholstery and carnation decor - also

Most best method for updating any chipboard or wooden cabinet, of course, painting is not as expensive as it seems at first glance and is quite simple to perform.

Painting a wooden cabinet made of chipboard

Paint selection

For wood and chipboard processing, you can use alkyd or acrylic,
spray paint or regular wood paint,
for deeper staining - varnishes, but most often preference is given acrylic paintm.

They are non-toxic, dry when room temperature, which in our case and when painting home furniture is very convenient, in stores they are presented in a wide range, you can colorizedb, i.e. dilute with white paint, achieving desired color... In addition, there is a choice of acrylic paints with a mother-of-pearl effect or, for example, metallic.

Spray acrylic paint adheres better than conventional paint to the surface, creating a smooth and evenly painted texture. It is easy to work with both a professional and a beginner.

Varnishes are mainly used to give furniture an antique, but well-groomed, noble and rich. In this case, the surface is painted over several times after each layer has completely dried.

Varnishes are also needed to set the color and protect the surface from scratches and minor damage.

You will need varnish even if you decide to paint the chest of drawers in an antique or Provence style.

Selection of brushes and roller

After choosing a paint, special attention should be paid to brushes and rollers. Why not save on painting supplies if you decide to update your chest of drawers with your own hands?

When the right technology old surface treatment and good staining the cabinet will maintain its appearance for several years.

Using bad brushes will not prevent freshly painted furniture from sticking to hairs or lint, which is almost impossible to fix imperceptibly.

If your task is to paint a large smooth surface, then for work both roller and aerosols will do.

ATTENTION: During work, do not leave brushes dry, it is better to put them in a jar of water, otherwise they will quickly become unusable

Technologists and painting technique

Do not forget about other important painting tools and materials, such as sandpaper or sander, primer, putty, thinner and varnish. All this is necessary to comply with the correct staining technology.

Equipment:

Different sandpaper grit is needed for pre-rubbing the old paint layer and sanding the surface.

A primer is needed for sealing small cracks on the surface of wood or chipboard.

Putty (you can take a car) and a spatula are useful if you have deep scratches, chips.

A solvent or white spirit is needed to degrease the surface before painting for better impregnation.

The varnish has a protective function and gives the furniture a shine.

In general, preparing the cabinet for painting consists of 5 short, but very important stages.

First, carefully remove the old paint and use a medium-grain sandpaper (or typewriter) align the work surface.

All dust must be brushed off, but without using wet rags, sponges etc. Otherwise, the old paint will only be absorbed better, and the new one will not lie well.

After processing with the finest grain degrease with white spirit (with acetone) and apply a primer for better adhesion to the paint.

If there are large chips, then we pre-fill them with putty and rub until smooth. After that we apply one or two layers of primer.

When you know all the stages of preparation, it's time to move on to the main stage and figure out how to paint a wooden chest of drawers and chipboard.

Master - class No. 1. Painting under a stencil

Everything is mixed in this cabinet - romanticism, Chinese motives, and even something from Gzhel. Everyone sees something of his own in him. We will study the painting technique.

Materials and tools

Prepared cabinet;

white paint;

solvent;

spray paint in blue;

gold paint;

stencil;

brushes.

Step by step guide

Step 1.

We remove all accessories, locks, handles, etc. from the cabinet. Using the familiar technology, we will prepare a wooden cabinet for painting.

We spread newspapers or a large piece of polyethylene on the work surface (on the floor) so as not to spoil other furniture.

Step 2.

We take white enamel and a solvent. In a small plastic jar we dilute paint and solvent according to the instructions on the paint can.

The paint consumption is also written on the can, it is better to use this information and dilute immediately required amount... If you mix a little paint, you may get a different color a second time.

We make the background of the picture - apply the first coat of paint... Leave it to dry completely.

Step 3.

If the color is saturated and you like it, then take a stencil and put it on the cabinet... Gently glue on the front side and side walls so that there are no bubbles.

Shake the spray paint well and spray it over the stencil... For an even color, one layer of blue paint will be enough, so we do everything the first time.

Step 4.

While the blue paint dries we paint the accessoriesremoved from the cabinet, in gold leaf. After the parts are dry, we screw them into place.

We remove the stencil from the cabinet and place it in the most prominent place in the room - because now it deserves special attention!

You can decorate the cabinet with a stencil, for example, flowers.

Master class No. 2. Renovation of the chipboard cabinet

This cabinet looked very cheap as it was made from chipboard and was conceived. But we have updated it with a beautiful ornament for a children's room, now it can fit into the interior, even hi-tech or modern.

Materials and tools

Prepared cabinet;

white paint;

pencil;

building level;

sponge brush;

masking tape;

additionally: protective paint (enamel).

Decor process

Step 1.

We will prepare furniture by cleaning surfaces from roughness, chips, cracks with putty and primer.

After use special means need to give dry the surfaces completely.

We take masking tape and stick it on the front side of the chest of drawers according to your individual idea.

We make combinations of triangles at the top and bottom edges, rhombuses in the middle, rectangles at the top and bottom. Cut off the strips and make shapes from them, as shown in the photo.

We make a rhombus by cutting out strips of equal length and placing them perpendicular to each other.

To make rectangles, first glue the tape evenly, parallel to the cut of the chest of drawers, and using building level and a pencil, mark equal intervals. Cut through one.

TIP: Pay attention to the placement of the fittings (handles, locks) and the gaps between the drawers - it is better to be symmetrical than even.

Step 2.

Step 5.

The final stage is the application of protective enamel. It will extend the service life of the chipboard cabinet and protect it from small mechanical influences such as moisture and dust.

And now the stylish wardrobe is ready for active use!

Color options can also be the same as in the photo below.

Master class No. 3. Painting a polished cabinet

Someone cannot believe that such a candy can be made from an old polished cabinet in vintage style, and without loss of functionality. And here's how to do it.

Materials and tools.

Old polished wardrobe;

vintage paint (regular acrylic matte);

white spirit or acetone;

brushes;

sandpaper or sander;

gold handles for boxes.

Painting process

Step 1.

Despite the fact that we are creating a vintage effect, there is no real shabby chest of drawers. Therefore, we carefully prepare it for painting.

To do this, remove all the old hardware and grinder we process the entire surface of the chest of drawers. First, we use coarse sandpaper, then fine-grained.

It is not necessary to putty and prime, except for severe chips on the surface. We degrease the surface with white spirit or acetone, let it dry.

TIP: Since the paint will be applied in several layers, it is very important that it absorbs well into the wood.

Step 2.

We cover with the first layer of paint. Very thin, you can not try too hard and leave unpainted areas.

Rub the first layer with fine-grained emery paper. We clean it from dust, but do not use wet rags, sponges, etc. in the process. We erase only with a dry cotton lint-free cloth.

Next, we apply the second layer of paint, also rubbing it in. Leave to dry and rub a little again.

We repeat this until the color becomes even, but a little rough. For this we used matte paint with a vintage effect. After a few days, it is completely absorbed and dries out and begins to turn yellow (pay attention to the instructions on the can so that you do not have to repaint it all over again). To avoid this, you can try this staining method on a small and inconspicuous area. Proceed with the full coloring when you are satisfied with the result.

If you bought new pens, check if they match the color and screw into place. The antique white chest of drawers is matched with golden brass carved handles with patterns.

Check the chest of drawers for compliance with your requirements - it is still comfortable, beautiful, and here's the paradox - modern. Vintage is in fashion now!

Wallpaper or film

When using a film or any other paper covering to renovate the cabinet, remember that we use the cabinet every day. And usually such a coating does not last long, but it is very simple to perform.

Cloth cover

This is the most painstaking way of updating the cabinet, when the fabric is stretched over the entire plane. The method is rather outdated. But maybe someone will like it.

Spot painting for a polished cafe

Spot painting is perfect for a polished cabinet. In this case, it is not necessary to remove the varnish and sand the surface. The technique is simple:

Using a marker, a drawing is applied

The marker is used to paint with dots. Details - here.

Cabinet renovation ideas

Self-adhesive film is an excellent material in finishing, allowing inexpensive, quick and beautiful renovation of furniture that has lost its attractiveness. How to properly glue a self-adhesive film on furniture, the nuances of work, which type is better and how to use it correctly, we will discuss in this publication.
Not everyone, for material reasons, can afford to replace the old furnishings with a new headset.

Living on rented apartment while waiting for the acquisition of new housing, spending money on the purchase of a new one is impractical.
Contemplation every day of the old environment often spoils the mood, therefore, pasting with self-adhesive film would be an ideal and inexpensive option to transform its appearance. Self-adhesive perfect solution for decorating country furniture.
Manufacturers today produce self-adhesive in a large assortment of types, sizes, textures, characteristics, textures that will satisfy any wishes.
Self-adhesive is used to transform the appearance of not only furniture, but also window sills, countertops, doors, windows, platbands, glass, and other interior items.
A large assortment will allow you to choose the right material for all rooms in the apartment. Your task is to choose the right one.

Selection of films for furniture

The defining composition of the film is the type of the main polymer component, the plasticizer that makes it elastic, pigments, and other additives, depending on the type of material.

If we consider how to properly glue a self-adhesive film on furniture, then you need to get acquainted with its main types. There are several types of film, they can be classified according to the following criteria.

Film type according to the composition of the components

Polyvinyl chloride (PVC);

Polyester;

Propylene.

By type of outer surface

The surface of the film determines its use for furniture of different directions, rooms, achieving the desired effect in conjunction with the overall design as a whole.

Glossy most appropriate in rooms without daylight, dimly lit rooms located on the north side.

Matton the contrary, it will well complement the design of light and spacious rooms.

Transparent used to protect against scratches, cuts, glass surfaces.

Holographic looks spectacular in any room, creating the effect of "play of light". Shades change depending on the angle of illumination, as well as its visually perceived volume.

Mirrored irreplaceable in small rooms, visually enlarging them. When the right combination colors, arrangement of interior items, you can achieve harmony and originality in the construction of the overall design.

By structure
Single layer films are made from a combination of ingredients - various plasticizers, resins, pigments, stabilizers.

Double layer - the name itself suggests the presence of two layers. The bottom (base) is made of paper or fabric. The top layer consists of a specific combination of polyvinyl chloride resins, where the pattern is applied.

Manufacturing is carried out according to different methods. When gluing, the film is detached from the base and glued to the surface. How to properly glue the self-adhesive film on furniture is described below.

By decoration

A huge assortment of this material has won great consumer demand. Consumers are offered an extensive selection of products for furniture decoration of various premises. A wide variety of colors, types of film allows you to choose exactly your finishing option.

It is presented in the form:

imitation of wood of different species;

natural stone;

ceramic tiles, mosaics;

leather, fabric, velor, tapestry, cork, and other materials;

under gold, silver;

children's motives from fairy tales, cartoons.

There are many more options to list. Dress furniture furnishings in new clothes, PVC film will help you to give it an updated design, since it is recommended to glue it on furniture.

The main advantages of self-adhesive film

After getting acquainted with the types of film, we will move on to the question of how to properly glue the self-adhesive film on furniture, outline the sequence of work.

How to stick a self-adhesive film on furniture

Preparatory stage:
The base before gluing must be flat, smooth, without roughness, cracks. Fill the cracks with putty, sand it. Otherwise, the film will repeat all the flaws in the base and will not adhere well.
The surface must be cleaned of any kind of contamination.
Remove the handles - screw them back on after finishing work. Glass, decorative overlays, also temporarily dismantle the moldings.
Degrease the prepared base with any dish detergent. Wooden base cover with acrylic varnish.
Cutting material
Before buying self-adhesive, draw a sketch with the dimensions of the elements to be glued. This will help you choose the right size for the width of the material (rolls are sold in different widths), so that there are as few joints as possible. Ideally, on small areas, there should be no joints at all.
After purchasing the material, cut it out correctly according to the details on the back side - there is a marking grid in multiples of 1 centimeter, which is very convenient. Cut out each piece and proceed to the main step.

Pasting furniture with self-adhesive film

If the pasting element is small, for example, the door from the kitchen cabinet, then here you can glue it on dry, and if you need to glue the cabinet with self-adhesive film, then better foundation moisten with water, soapy water solution.
Then the self-adhesive will not immediately stick firmly, it will be mobile, so you can even out any distortion. This happens if you are gluing for the first time.
How to properly glue a self-adhesive film on furniture is not such a complicated process - the main thing is accuracy, accuracy in measurements, and lack of haste.
The canvases should be glued from above. If these are doors, then they can be removed. Separate the self-adhesive from the protective backing by 8 - 10 centimeters and apply it tightly to the top of the glued element. Fix by smoothing this area from the center to the edges with a cloth, pressing well.
The bottom hangs down with the backing. Little by little separate upper layer from the backing, smooth the piece to be glued well. So small areas go down, removing the protective layer, and sticking well, expel bubbles.
Evaluate your work, and if you see bubbles on the surface, then pierce them with a thin needle, squeeze out the air, press this area. If suddenly a wrinkle appears when smoothing, then warm this place with a hairdryer and smooth it again.

Let the film dry out if water was used and get used to its new habitat, after which you return the fittings and glass to their place.

How to remove self-adhesive film from furniture

If the self-adhesive has been glued for a long time and has become untidy, you have damaged it, then it is better to remove it and stick a new one.
During the next repair, the previous self-adhesive design does not harmonize with the rest of the interior items, then remove it and replace it with a new one.
We examined how to stick the film on furniture, and the principle of removal is based on heating adhesive compositionwhich will then easily detach from the surface.
Remove the self-adhesive with a hairdryer
Use a hair dryer - for small areas, a hair dryer is suitable, and if the area is large, use an industrial one. Start heating the film and at the same time pull it slowly and gently so as not to tear.
Glue residues may remain on the substrate. Remove it with gasoline, thinner, alcohol, white spirit or others. It all depends on the base material. To avoid damaging the base, try applying the compound to an inconspicuous area. If everything is ok, then use it.
Correct care
Self-adhesive film care is reduced to wiping it with a damp sponge. If stains are greasy, wash with liquid detergent.
Do not use powder-type products to avoid scratching it. Solvents can damage the film; it is better to wipe the dirt with a swab with alcohol.
Pasting furniture is available to everyone - this is a simple, but also an exciting process. We got to know how to properly glue the self-adhesive film on the furniture, it remains to choose the right one and start transforming your apartment.

Self-adhesive tape is a versatile tool that can be used to hide scratches and various other defects. It has a very attractive appearance, a wide range of colors, excellent durability and an affordable price. However, in order for everything to work out as it should, you need to know how to properly glue the self-adhesive film on different types surfaces.
General information about the material
With the help of the film, you can not only disguise various defects on furniture that appeared during operation, but also refresh its appearance with minimal financial costs. In the presence of material and ordinary office scissors, the pasting process will take no more than one hour.
Many people choose film for the following benefits:
the film is sold in rolls, so it is very easy to work with it;
the material is quite durable, thanks to which it perfectly protects furniture from any mechanical damage;
the material has a fairly low cost;
no special tools are required to work with the film;
the material perfectly protects furniture from dirt, grease and any kind of other stains;
very easy to clean.

Considering all the listed advantages, we can say with confidence that this material is one of the most versatile, with which you can quickly and cheaply update interior items, as well as make them fresher and more interesting. However, in order for the final result to meet all your expectations, you need to know how to properly glue the self-adhesive film on furniture.
Material features
The high performance characteristics of the film are due to its features. It consists of three layers, each of which is designed to perform a specific task.
The first layer is the front one. It can be made from polymeric materials, foil or paper. This layer performs exclusively protective functions and prevents damage to furniture by mechanical stress.
The second is the decorative layer. It gives interior items a more aesthetic and attractive appearance. The film can imitate various types of surfaces, so each person can choose the perfect solution for their interior, which will be in perfect harmony with all decorative items.
The last layer is protective. It is removed before the film is adhered to the surface.
So, we already know about the advantages of raw materials and about its features, however, before answering the question of how to glue the self-adhesive film, it is necessary to understand the main varieties of this material.
Varieties of film
There are two main types of self-adhesive films, which differ in composition and production technology:
Single-layer - made of polymeric materials and special additives that increase the strength and durability of the material.
Two-layer - the film consists of two layers, among which the first is the main one, and the second performs decorative functions. It is much cheaper than a single-layer one, but it has worse performance characteristics.

So, how to glue self-adhesive tape with your own hands? This does not require any tools or special skills, so anyone can cope with everything. And in more detail about the pasting process will be discussed later.
Applying self-adhesive films to furniture
Many have a home old furniture, which is quite worn out and needs to be replaced, but there is simply no money to buy new furniture. Therefore, each person is interested in the question of how to glue a self-adhesive film on furniture. The first step is to prepare a set necessary toolswhich includes the following:
stationery scissors;
a piece of soft matter;
roller;
acetone;
primer;
sanding paper.

When the inventory is ready, you can start preparing the surface for film application. To do this, the furniture must be primed, which will significantly increase the quality of adhesion of the material to the furniture. It is also worth tightening all the bolts so that the furniture does not crack or wobble.
After the primer mixture has completely dried, you can start applying the film. This is where the answer to the question of how to glue the self-adhesive film begins. The first step is to take measurements from the furniture, on the basis of which the film is cut into pieces.
When applying the material to furniture, a protective layer is removed from one end by about 10 centimeters, after which the film is carefully and slowly applied to the furniture. So that after gluing there are no folds left and air bubbles, the material is smoothed with a roller or soft cloth.
How to glue the self-adhesive tape in an easier way? To do this, you need a soapy water solution to moisten your work surface. Then the protective layer is completely removed from the film, and it is applied to the furniture, after which it is smoothed with a piece of cloth.
Film application on walls and doors
An equally common question that interests many people is: "How to glue the self-adhesive film on the wall?" The process of applying material to these types of surfaces has much in common with the one described above, but there are some differences.
To get started, you need to prepare the following tools:
ruler;
stationery knife;
simple pencil;
spatula with felt;
hot air gun.

If you have everything you need at hand, you can start applying the material. The first step is to prepare the wall for pasting. For this, the old coating and glue are removed from it. Further, the wall or door is treated with gasoline or alcohol and left for a day to dry completely. This is necessary to degrease the surface. To achieve better adhesion, the wall can be primed.
When the surface is fully prepared, you can start pasting with film. It is applied in separate parts, so the material is first cut into certain pieces. In this case, you should leave a small margin. When applying the material to a wall or door, you must be extremely careful so that it lies perfectly flat on the surface. To avoid air bubbles under the film, the material is thoroughly smoothed with a roller.
Sticking film on glass
How to glue a self-adhesive film on glass? Very simple. First of all, the glass should be thoroughly washed from dirt and wiped dry so that no streaks remain on it. After that, the surface must be degreased with isopropyl alcohol. Further, the dimensions are taken from the glass, according to which the necessary piece is cut out of the film. In this case, you should take a small margin, which is necessary to eliminate possible errors.
Before applying the material to the glass surface, the latter is pre-moistened with soapy water. The protective layer is completely removed from the film, and the material is applied to the glass, during which the film is smoothed with a squeegee. Smoothing should start from the center, gradually moving towards the edges of the glass. The excess film is cut off.
Common mistakes
So, you already know how to glue the self-adhesive film on the door. However, in order for the result to completely satisfy you, the following mistakes should be avoided:
the film should be applied to a perfectly clean surface;
when cutting the material, it is always necessary to take a small margin so that the film is enough for pasting the shield;
in order for the pattern to match, the film should be cut exclusively at the seams;
so that after applying the film to any surface no defects are visible, it should be thoroughly prepared in advance.

Conclusion
In this article, you learned about all the nuances of applying self-adhesive tape to various types of surfaces. However, in order not to spoil the material, you should strictly adhere to the technology of its application, which is indicated by the manufacturer on the package.